This igniter has a short wire harness. The wire length is approximately 6 inches long.
How Buying OEM Parts Can Save You Time and Money
Part Videos
Replacing your Frigidaire Range Broiler Igniter
Troubleshooting
This part fixes the following symptoms:
Gas igniter glows | but will not light | Will Not Start
This part works with the following products:
Range.
This part works with the following products:
Frigidaire, Kenmore, Crosley, Electrolux.
Part# 5304506545 replaces these:
AP6036346, 316489404, 7316489404
Customer Reviews
Average Rating:
★★★★★
★★★★★
1 Review
4.0
Filter By Rating:
5 Stars
0
4 Stars
1
3 Stars
0
2 Stars
0
1 Star
0
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Edward M - March 28, 2018
Verified Purchase
Fast easy and correct
The igniter arrived sooner than I thought . installed easy and was the correct part.thank you for your excellent service.
< Prev
1
Next >
Customer Repair Stories
Average Repair Rating: 4.4 / 5.0, 1 reviews.
What's this?
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
replace bad oven ignitor
Oven ignitor is on the bottom gas unit. Ignitor is in oven and plug is in warmer oven on left wall at very back of warmer oven. It has duel function to light both upper and lower gas burners (in oven). Wires of new plug that I received were shorter than existing wires and would not reach the plug from ignitors center mount location to
... Read moreplug at far back of warming unit on left wall. Even if the wires would have been long enough, I couldn't figure out how to "release" the existing plug. Easy solution: Cut old wires at junction of old ignitor (leaving wires as long as possible). Cut new wired as close to new male plug as possible (leaving wires as long as possible on new ignitor). Strip ends of old and new wires and wire nut with porcelin wire nuts (hardest part of job was locating porcelin wire nuts)! After placing wires out of the way of burner and ignitor, reassemble stove parts. AVOID touching new element as oil from hands will decrease the life of the element. Good Luck..
Read less
Mike from PROVO, UT
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
9 of 10 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
Next >
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
5 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Jeremy
September 30, 2017
This part, is it the one that's below the floor of the oven? The one that heats up and will allow the gas tube in the floor of the oven to actually be lit? Mine is currently glowing but after 90+ seconds still won't light the gas and as such i don't get any heat in my oven. The other part that it recommended(316489403) looks like it'd be replacing one in the top of the oven for a broiler lighting. Is that correct? Just want to make sure i order the right part.
For model number 790.77433902
Hi Jeremy,
Thank you for your inquiry. Yes this bake element is under the bottom panel in the oven. I hope this helps. Thank you and have a great day!
5 people found this helpful.
Was this helpful?
Thank you for voting!
Dorothy
May 29, 2023
My gas range left front burner is blocked, can not ignitiate, have no fire. It might blocked by wax. How can I reopen it and have fire? Replace head would be useful? Do you have the spare parts available?
For model number FGGF3036TFE
Hi Dorothy, thank you for reaching out. According to our research, you can clean the burner head by using a straight pin or paper clip. Remove any blocking material. If it does not help replace the left front burner, part number PS2364157, to fix this issue. We hope this solves your issue!
Broiler glows but does not ignite. Would this part be the cause?
For model number 790.74332310
Hello Jeffrey, Thank you for the question. We suggest testing the Igniter. With a multimeter set to OHMS, connect to both igniter leads. On a good igniter, there should be between 40 & 400 OHMS. A bad igniter will show no resistance or continuity. We hope this helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Tammy
December 22, 2023
So my broiler would glow but would not ignite and I changed the broiler igniter and it still will not come on what is the next thing that I need to check?
For model number LGGF3043KFS
Hi Tammy, thank you for reaching out. As you have already replaced the broiler igniter, we would recommend checking the oven safety valve, part number PS5136194. It controls the gas flow to the bake and broil burners in the oven. You may need to replace it to fix the issue. We hope this solves your problem!
I have replaced both control board and broiler igniter but the broiler still doesn't light. oven works fine. any suggestions?
For model number LGGF3042KFP
Hi Bob, thank you for the question. Based on our understanding, we would recommend checking the broil burner, part number PS2581761. You may need to replace it to fix the issue. We hope this sorts out your problem!
