Refrigerator Freezer Gasket 5304505782

Hello Joyce, Thank you for contacting us. I have researched the model you have provided and have found the part you are looking for is Part Number: PS976757. Hope this helps, good luck with this repair!

Hello Tina, thank you for your question. We have researched your model and found that both the freezer and the refrigerator require only one gasket, part number PS11766245. You need to order only one gasket. If you need help placing an order, customer service is open 7 days a week. Thanks again for your great question.

Hello Mo, thank you for your question! To replace the gasket, you first need to remove the door of the refrigerator. To remove the door, first, remove the plastic top hinge cover. Hold the door in place while removing the top hinge from the cabinet. Remove the two bolts from the top hinge. Lift the door upwards and pull it up and away from the cabinet until the bottom hinge pin is mounted on the front of the cabinet. Now that the door is on a suitable work surface, you can now exchange that gasket, which is actually mounted to the door and held in place by the inner door panel. It’s kind of sandwiched between that inner door panel and the older door frame. You will need to loosen all the screws around the perimeter of that door. They do not need to be removed; you can just loosen them about a quarter of an inch, and that will allow you to pull the gasket out from beneath the inner door panel. You will note that there is a channel around that inner door panel, and the gasket actually has a bulbous edge on it that will fit up into that channel to hold it properly in place. So just loosen all of those screws all the way around the perimeter of the door. So once you have those screws loosened, you can just pull that gasket out from beneath the inner door liner, and you’ll see a little rib around the edge of that gasket and where it fits into this channel on the inner door panel. So just pull it all the way around and remove it. And once you have all the screws loosened, you can now pull that gasket out from beneath the inner door liner; that’s when you’ll note that little rib around the edge of the gasket and the channel on the edge of the door panel. So just peel that out, all the way around. And use some caution so that you don’t damage that inner door panel. And then you can discard the old gasket, and just lay that new gasket around the door. And because of the type of packaging that gasket arrives in, you will need to either heat it with your clothes dryer, a hair dryer, or soak it in a bathtub in hot water, and that will make it pliable and allow you to work out any of the kinks that may have occurred during shipping. So once you’ve got that softened up and in good shape, you can then begin to install it on the door. Now, we recommend starting in one of the corners and just inspecting that edge of the older door panel first, to make sure that there’s no crud built up there that needs to be removed first. Just start by hooking that corner into position, and work that little rib in under the edge of the inner door panel, and just fit that rib in under that inner door panel, and make sure it’s nice and flush on the outside, and then while holding it in place. Just tighten up that screw a little bit. And then work your way along the door, fitting it in as you go, and then just periodically tighten up on the loose screws to hold it in place. And continue to do that around the door, taking care in the corners to make sure that we have it nice and square and even. And once you have got the gasket fitted in around the door, you can tighten up the screws. So just carefully lift that door, line it up with the bottom hinge, and set it into position. Set the top hinge into the socket and install two bolts. You won’t tighten these bolts yet; you will just put them in all the way, and then you will line up the door before we tighten them up. We hope this helps, good luck with this repair!

Hi Reg, thank you for contacting us. The door gasket you mentioned is approximately 65.16" x 31.50". We hope this helps.

Hello Tony, Thank you for your inquiry. We have researched the model number that you have provided and the door gasket is part# PS11766245. You could also have an issue with the door switch which you can test with a multimeter. If you are unfamiliar with how a multimeter functions, we have videos available to assist you. We hope this helps and if you need help placing an order, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you!

Hello Paul, thank you for your question. Yes, the Gasket PS11766245 you had chosen is compatible with your model. If you need help placing an order, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you.

Hi Doug, thank you for contacting us. Yes, the mentioned part is the compatible gasket for your model. Please submit a new question if you have any follow-ups!

Hi Sandra, thank you for your question! The freezer door gasket for your model is part number PS11704172. Glad to be of assistance!

Hello Donna, Thank you for your inquiry. We have researched the model number you have provided and confirm that this part will fit your model. All of the prices on our Canadian site are in Canadian dollars. We hope this helps and if you need help placing an order for a part, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you!

Hi Andy, thank you for the question. According to our research, the problem appears to be with the Door Gasket, part number PS11750673. The door gasket creates a seal around the door to prevent warm air from entering the freezer, we would recommend checking it. If you require assistance placing an order, please contact customer service. We hope that helps!