We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
7 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
James
February 24, 2018
I am needing the timer part where you select the cycle. Is Partselect number ps11759041 and manufacturer part number we04x24551 the right part?
For model number GTD45EASJ2WS
Hello James,
Thanks for your question. Yes, part number PS11759041 is the timer which is used for your cycles.
I hope this helps.
9 people found this helpful.
Was this helpful?
Thank you for voting!
Kerry
April 18, 2018
I just bought this dryer used and the dial won't move from where i set it on the cycle, i.E. More dry, less dry, etc. So it runs indefinitely even after the clothes are very dry. It gets hot and dries the clothes without a problem. I think one time out of about 8 it did seem to work on delicate cycle only. Would this most likely be a faulty timer, thermostat, or sensor? Thank you!
For model number GTD45GASJ0WS
Hi Kerry, Thank you for the question. This does sound like an issue with the timer switch,Part Number: PS11759041. The switch is not repairable so it will need to be replaced. Hope this helps!
6 people found this helpful.
Was this helpful?
Thank you for voting!
Dee
November 17, 2019
Which timer/selector switch do I need to replace factory part tmd1gm29?
For model number GTD45EASJ2WS
Hi Dee, the replacement is PS11759041. Thank you for your question and good luck with your repair!
3 people found this helpful.
Was this helpful?
Thank you for voting!
Anthony
February 27, 2020
Does the timer (part # ps11759041) come with the knob or do I have to buy it separate?
For model number GTD45EASJ2WS
Hello Anthony, Thank you for the question. The Timer Knob, PartSelect Number PS11736611 is sold separate from the Timer Switch. We hope this helps.
Ok the dryer was check out by the place i am get it from it's not get hot and the man told me i was not get eney power to the timer
For model number GTD45EASJ2WS
Hello Charles, Thank you for the question. I suggest checking the Dryer Board, PartSelect Number PS11772028 and the wiring tot he timer to make sure everything is secure. You may need to replace the timer as well. Hope this helps!
2 people found this helpful.
Was this helpful?
Thank you for voting!
Kathy
May 20, 2019
I have a 2 year old GE dryer and i have noticed the the heat cycle will not advance i can be drying clothes all day if i did not shut it off by opening up the door. Thanks kathy
For model number GTD45EASJ2WS
Hi Kathy, thank you for your question. Looking at your model information there are a few parts that you should take out and test to see which one is giving you the issue. The first parts to check in this case would be all of your thermostats and thermal fuses. You can test those parts with a multi meter and they should be reading 0 ohms to be working correctly. If those parts are fine, you should then go on to testing your heating element as well. You can also test that with a multi meter and it should be reading between 0 - 50 ohms. Something else you should also check would be your filter and ducts. Make sure there is absolutely no blockage that would restrict air flow in your appliance. I hope that helps. Good luck with your repair.
2 people found this helpful.
Was this helpful?
Thank you for voting!
Belinda
August 15, 2022
does a GE WE04X24551 REPLACEMENT TIMER WORK ON THIS MODEL
For model number gtd45easj1ws
Hello Belinda, Thank you for your inquiry. We have researched the model number you have provided and confirm that this part will fit your model. We hope this helps and if you need help placing an order, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you!
Was this helpful?
Thank you for voting!
< Prev
1
Next >
Customer Repair Stories
Average Repair Rating: 3.2 / 5.0, 4 reviews.
What's this?
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
unable to set timer, knob stripped
Timer was extremely difficult to turn, causing the knob to strip. Unplugged power to dryer. Pulled knob off, pulled dryer out to get at the back side, removed the small bolts that hold the back on, pulled back off and let it hang by the ground wire, looked at switch away and saw it was attached by a nut and a torque screw,and two hooks, removed screw and nut, looked at new switch,I put a little oil on the shaft to free it up,and aligned it the same as the old one, took the old one off by sliding it up to clear the hooks and let it hang by the wires, installed new switch with nut and torque screw and hooks. Then looked at the wires on the old switch and transferred each wire one at a time to the same terminal on the new switch. Screw the back on to the dryer, plug power in, move dryer back in place put knob on.
Two surprises: (a) after removing two screws, instrument console required a hard whack to slide it back so it would come off; and (b) the timer was held in place by a torx (T-15) screw. The photo I took of the wiring was essential for installing the new timer.
Knob broke so we were using vise grips to turn with. The stem broke off so we had to replace the timer.
Took pics of the wiring after taking off back top plate. Found PartSelect on line. Put in part and ordered, quick,easy and simple. They did everything as stated. Put all wires back on and closed up. Tickled pink with PartSelect and will definitely use them again.
DRYER TIMER KNOB WOULD NOT MOVE....CRACKED THE KNOW
REMOVED BACK COVER REMOVED THE SCREW HOLDING THE COMPONENT TO THE FRONT TOOK PHOTO OF HOW THE COLOR WIRES CONNECT REMOVED THE WIRE (TOOK THE LONGEST, HAD TO USE NEEDLE NOSE PLIERS TO BREAK THE TAB FEMALE TAB LOCKS. RE-WIRED THE NEW CONTROL PUT PLATE BACK ON DRY NOW RUNS AS INTENDED
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Fred D - December 4, 2022
Verified Purchase
Exactly what I needed
I saved a lot of money fixing my dryer myself. The replacement part was the exact correct part and fit easily.
★★★★★
★★★★★
Larry N - September 22, 2022
Verified Purchase
Dryer selection switch and timer
Everything was awesome!
The arrival of the part was quick! Installation was fast and easy!!
The dryer is performing fabulous! Thanks
★★★★★
★★★★★
Gesenhia L - September 11, 2022
Verified Purchase
Part as described
My appliance is back in working order.
★★★★★
★★★★★
Donald R B - August 29, 2022
Verified Purchase
Part Pin out
replacement Part pin out was incorrect to OEM , part was ordered by match to part number , and model- no instructions for missing pins - lucky machine wiring diagram - noted to delete hook up of the 3 missing pins tape off but no instructions with part .
★★★★★
★★★★★
Donald R B - August 21, 2022
Verified Purchase
Not easy
Part was to be match to OEM was not same pin out , used dryer wiring diagram to adapt
★★★★★
★★★★★
Frankie R - July 29, 2022
Verified Purchase
GE Dryer Timer
The part was an original replacement part, exactly like the OE part on the dryer.
The replacement was simple; with only one challenge. The wire connectors have a
pin the latches into holes on the male prongs on the switch. It was a little difficult
to unlatch the pins to remove the wires from the original connector.
★★★★★
★★★★★
KIMBERLY N - April 11, 2022
Verified Purchase
Right part a plus
Fits great, no issues. Ladiy at store had all info on what I needed. Very knowledgeable. Thanks
★★★★★
★★★★★
Michael M - September 26, 2021
Verified Purchase
Good part..
Had to you tube video on install.needed t8 screwdriver to install just followed the wires from previous part..seems to be working
