Part Location Diagram of W11122012 Whirlpool SWITCH-INF
See part 6 in the diagram
Part Location Diagram of W11122012 Whirlpool SWITCH-INF
Customer Service Representative

Get in touch, we're here to help!

Daily 8am - 9pm EST

customerservice@partselect.com

SWITCH-INF W11122012

Rated by 2 customers 

Easy 

1- 2 hours 

Ratings submitted by customers like you who bought this part.

$ 149.73
  In Stock

Get this part fast! Average delivery time for in-stock parts via standard shipping: 1.8 days.

PartSelect Number PS12347325
Manufacturer Part Number W11122012
Manufactured by Whirlpool
Troubleshooting
This part works with the following products:
Cooktop, Range.
This part works with the following products:
Amana, Caloric.
Part# W11122012 replaces these:
0307455, 0312934, 10027901, 10027906, 312934, W10894488, WPY0307455, Y0307455, Y0312934
Back to Top
Customer Repair Stories
 Average Repair Rating: 2.6 / 5.0, 2 reviews. What's this?
Sort by:
  • 1
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Replacement of burner control switch
1. Open the circuit breaker feeding the range. Turn all range control switches ON to establish that there is no power. Remove all knobs.
2. Get under the range and remove the 2 hex-head screws securing the flex conduit to the bottom panel. Then remove the 20 hex-head screws securing the panel to the range. Lower the panel and place aside, and then after checking for no voltage disconnect the red and black incoming wires by pulling on the spade connectors. Make sure you mark which wire went where.
3. From below apply pressure to the range frame to free the top surface gasket from collected food debris, then from above lift our the range and place upside down on a towel. Support the range with wooden blocks so that the unit is not resting on the knob shafts.
4. The control switches are all mounted on a common bracket with two screws for each switch. The first task is to remove two screws on each side holding the bracket to the frame, and then two wire harnesses on each side. Then gently move the bracket and rotate it sidewards so you have access to the screws holding down the switches.
5. Remove the defective switch leaving all the wires still connected.
6. Install the new switch and transfer the wires from the defective switch.
7. You're done, now restore everything in reverse, just make sure all wires move freely and not pinched.
Read less
  • Farouk from Sudbury, MA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    More than 2 hours
  • Tools:
    Nutdriver, Pliers, Screw drivers
10 of 12 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
2 controls were damaged and not working correctly. One would not properly shut off.
1. Turned off the 240V branch circuit to the cooktop.
2. Removed and inverted the cooktop.
3. Removed the bottom panel, used 1/4-inch nut driver to remove the sheet metal screws.
4. Confirmed the circuit was de-energized. Voltmeter set to AC, measure across the L1, L2 connections, should be 0 VAC or very close.
5. Make a diagram of the existing connections to the controls to be replaced, note all control markings (L1, L2, H1, H2, PL) as the replacement controls have connectors in different locations.
6. Remove the AC Mains plate, 2 sheet metal screws.
7. Make a diagram of the primary AC distribution blocks.
8. Remove the AC Mains input leads, Red and Black.
9. Remove the AC distribution to the controls from the primary AC distribution blocks. Needed to free up the control panel.
10. Remove the 4 sheet metal screws holding the control panel.
11. Rotate the control panel to access the screws holding the controls. Caution on the wires to the heating elements, watch for pinching.
12. Remove one control with the wires attached.
13. Install the replacement control. Secure the screws.
14. Transfer the wires, matching the connection marking (L1, L2, H1, H2, PL) exactly.
15. Do the same (12, 13, 14) with the next control.
16. Re-install the control panel. Check all wires for clearance.
17. Re-connect the control wiring to the AC primary distribution blocks.
18. Re-connect the AC mains wiring to the primary AC distribution blocks.
19. Re-install the AC mains plate.
20. Visually check all the connections. Shake out any debris.
21. Replace the bottom cover, installing all screws.
22. Remove the gasket strip from the mounting lip, clean the surface, install new gasket (weather stripping).
23. Re-mount the cook top.
24. Energize the 240VAC branch circuit.
25. Test the controls. Correct any errors.
26. Done! Go have some hot tea! (or a beer)
Read less
  • Edward from Sunnyvale, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Pliers, Screw drivers
7 of 8 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • 1
Back to Top
Questions and Answers

Ask our experts a question about this part and we'll get back to you as soon as possible!

1 question answered by our experts.
Sort by:
  • 1
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Lanny
January 21, 2023
Burner on back right heats on high no matter what level it is set on.
For model number AK2T30E
PartSelect logo
Hello Lanny, Thank you for the question. This is normally an indication the Switch that controls the Burner is faulty and may need to be replaced. We hope this is helpful!

Was this helpful?
Thank you for voting!
  • 1
Back to Top
Model Cross Reference
This part works with the following models:
PartSelect Number: PS12347325
Manufacturer Part Number: W11122012
Brand
Model Number
Description
Amana
AK2H30
Cooktop
Amana
AK2H300E
Cooktop
Amana
AK2H300W
Cooktop
Amana
AK2H30E1
Cooktop
Amana
AK2H30E1-P1131546NE
Cooktop - ELECTRIC COOKTOP
Amana
AK2H30HR
Cooktop
Amana
AK2H30HRW
Cooktop
Amana
AK2H30W1
Cooktop
Amana
AK2H30W1-P1131546NW
Cooktop - ELECTRIC COOKTOP
Amana
AK2H35
Cooktop
Amana
AK2H35-P1131547N
Cooktop - ELECTRIC COOKTOP
Amana
AK2H35E1
Cooktop
Amana
AK2H35E1-P1131547NE
Cooktop - ELECTRIC COOKTOP
Amana
AK2H35HR
Cooktop - Electric
Amana
AK2H35HRW
Cooktop
Amana
AK2H35W1
Cooktop
Amana
AK2H35W1-P1131547NW
Cooktop - ELECTRIC COOKTOP
Amana
AK2T30E
Cooktop
Amana
AK2T30E-P1172101S
Range - Amana Range/Stove/Oven Model AK2T30E-P1172101S (AK2T30EP1172101S, AK2T30E P1172101S) Parts
Amana
AK2T30W
Cooktop
Amana
AK2T30W-P1172102S
Range - Amana Range/Stove/Oven Model AK2T30W-P1172102S (AK2T30WP1172102S, AK2T30W P1172102S) Parts
Amana
AK2T35E
Cooktop
Amana
AK2T35E-P1172103S
Range - Amana Range/Stove/Oven Model AK2T35E-P1172103S (AK2T35EP1172103S, AK2T35E P1172103S) Parts
Amana
AK2T35W
Cooktop
Amana
AK2T35W-P1172104S
Range - Amana Range/Stove/Oven Model AK2T35W-P1172104S (AK2T35WP1172104S, AK2T35W P1172104S) Parts
Amana
AK3H30HRW
Cooktop
Amana
AKH30HR
Cooktop
Amana
AKH35HR
Cooktop
Amana
CAKH30HR
Cooktop
Amana
FST130-2D
Cooktop
Back to Top
Customer Service Representative

Get in touch, we're here to help!

Daily 8am - 9pm EST

Contact Customer Service
SWITCH-INF
$ 149.73
  In Stock
✖
Stock Status
 In Stock

Item is in stock and will ship today if your order is placed before 4:00 PM Eastern Standard Time.

If your order is placed after 4:00 PM EST, the in stock items will ship on the next business day.

 On Order

Item is not in stock and usually ships 3-5 business days from the time you place your order.

 Special Order

Item is not in stock and usually ships 10-15 business days from the time you place your order.

 NLA - No Longer Available

This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.