Quick Question!

Have you ever purchased from PartSelect.com before?

See part 2 in the diagram

Motor Clip

Your Price

Get this part fast. Average delivery time via standard shipping: 1.8 days.

PartSelect Number PS11757442
Manufacturer Part Number WPY015825
Manufactured by Whirlpool

This part works with the following brands: Maytag, Whirlpool, Kenmore, Crosley, International, Jenn-Air, KitchenAid, Roper, Amana.

This part works with the following products: Dryer, Air Conditioner, Washer Dryer Combo, Dishwasher, Washer.

Questions & Answers

Ask our experts a question on this part and we'll respond as soon as we can.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 2.3 / 5.0, 3 reviews What's this?
1-3 of 3

24 of 29 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 1- 2 hours
Tools: Nutdriver, Pliers, Screw drivers
Customer: Jeffrey from Bend, OR

Rumble noise and groaning on startup.

I found that I replaced more parts than I needed to fix fhis problem. The source of the rumble was the blower wheel connection to the motor, allowing the wheel to wobble (plastic wheel flat spot worn off over time, no firm lock to the motor shaft). But the dryer should be good for another 10 years!

Disconnect dryer from electrical outlet and exhaust.

Remove the back access plate to release the belt from the pulley. Remove the two screws at the bottom front of the dryer, rotate the front to release it at the top. Remove the wires from the door status switch. Remove the 4 nuts holding the drum support frame and pull straight out. Remove the drum. Remove the two bolts holding the thermostat cover (silver odd shaped metal plate at the front of the dryer). Remove the dryer blower cover plate by removing the 6 bolts holding it to the blower housing. Remember to remove the bolt holding the plate to the bottom of the dryer. Release the door status wire from the clips on the left side of the dryer and set the blower housing plate to the right, out of your way without removing the wires. Remove the blower wheel by removing the Circlip at the front of the shaft and then removing the shaft compression clip. Pull out the blower wheel and then remove the rear Circlip from the motor shaft. The back of the blower housing can be removed by removing the 4 bolts holding it to the motor support frame to make access easier but this may not be necessary. Release the 5 wires attached to the motor. Release the front and back motor clips. I used a large straightblade scerwdriver to press down and out on the end of the clips. Lift out the motor. Remove the rear pulley from the motor using an allen wrench and transfer it to the new motor. Set the new motor in the support frame, ensuring the lips of the vibration isolation rings are pointed down to slip over the frame and are not facing up towards the clips ( makes clip instalaltion much easier). Hook up the wires, following the color coding on the motor controller you are attaching to. Reinstall the blower back housing if removed, rear circlip, blower wheel, front circlip, shaft compression clip, blower housing front cover (Including the bolt to the dryer bottom) , reroute the door switch wire up the left side, reinstall the thermostat cover, reinstall the drum and belt, reinstall the drum front support frame (ensure the felt seals for the drum and the blower cover are properly aligned and seated correctly), hook up the door status wire when your set the front cover and install the 2 screws, reinstall the belt through the pulley and idler wheel (make sure the belt smooth side is against the drum) through the back access panel and reinstall the panel.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

3 of 4 people found this instruction helpful

Parts Used:
Level of Difficulty: A Bit Difficult
Time to do repair: More than 2 hours
Tools: Nutdriver, Pliers, Screw drivers, Socket set
Customer: Mark from Bethpage, TN

Dryer made screetching, chirping noise then would stop running alltogether.

Turned off breaker, then unplugged it anyway. I need some room to attack this old dog! Pulled out of its hole beside the washer and went to work. Opps, don't forget the flexible vent, I broke it off about a foot from the dryer. Four screws on back, lower right to remove acccess panel. Next two screws under front panel, pull bottom out about a foot and it unclips at top. Read the 5 repair stories about replacing the motor as I took everything apart, all were helpful. Had to put motor in a vise to loosen set screw on pulley, lucky I had a 3/16 allen socket, that was the only hard part, unless you count getting screws out from under the freezer where I kicked them. Be careful. Still ended up with belt in v-groove on back part of drum (where it does NOT go) so had to reach in from front and pull it out about 4 or 5 inches. Things a quiet now and I am a hero around here. Thanks for the good help fellows.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 3 people found this instruction helpful

Parts Used:
  • Motor Clip
Level of Difficulty: A Bit Difficult
Time to do repair: 30 - 60 mins
Customer: susan from Socorro, NM

Both motor clips broken - >40 year old dryer!!

Removed the back - Saw the broken clips on the base of the dryer (the wires to the motor were pulling out because the motor was slipping).

Guessed that the parts were motor clips (no pix in the web site!)

Got the parts in post - they were identical except needed some rubber grips inside to hold tight (Used pieces of bike tire inner tube cut to fit for this.) Attached clips. Works fine!!

(Son is an engineer - he found the problem. Husband is a retired doctor - he couldn't!! but together they
supplied the muscle)
Sue (67 years old)

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1-3 of 3

Model Cross Reference

This part works with the following models:

PartSelect Number: PS11757442
Manufacturer Part Number: WPY015825
Brand Model Number Description
Kenmore1060359089Air Conditioner
Kenmore10663400Air Conditioner
Kenmore10663420Air Conditioner
Kenmore10663600Air Conditioner
Kenmore10663601Air Conditioner
Kenmore10663620Air Conditioner
Kenmore10663621Air Conditioner
Kenmore10663720Air Conditioner
Kenmore10663721Air Conditioner
Kenmore10663760Air Conditioner
Kenmore10664070Air Conditioner
Kenmore10664190Air Conditioner
Kenmore10664210Air Conditioner
Kenmore10664760Air Conditioner
Kenmore10665210Air Conditioner
Kenmore10665760Air Conditioner
Kenmore10665770Air Conditioner
Kenmore10666770Air Conditioner
Kenmore10667070Air Conditioner
Kenmore10667910Air Conditioner
Kenmore10667920Air Conditioner
Kenmore10667930Air Conditioner
Kenmore10667960Air Conditioner
Kenmore10668900Air Conditioner
Kenmore10668910Air Conditioner
Kenmore10668920Air Conditioner
Kenmore10668960Air Conditioner
Kenmore10669900Air Conditioner
Kenmore10669901Air Conditioner
Kenmore10669930Air Conditioner