Drain Pump - 120V 60Hz WPW10730972 | Official Whirlpool Part | Fast Shipping | PartSelect
Quick Question!

Have you ever purchased from PartSelect.com before?

Drain Pump - 120V 60Hz – Part Number: WPW10730972
Drain Pump - 120V 60Hz – Part Number: WPW10730972 Drain Pump - 120V 60Hz – Part Number: WPW10730972 Drain Pump - 120V 60Hz – Part Number: WPW10730972 https://partselectcom.azureedge.net/Schematics/Maytag/IAZWUPHM.gif

Drain Pump - 120V 60Hz

36 Reviews
Your Price
$108.37

Get this part fast. Average delivery time via standard shipping: 1.8 days.

PartSelect Number PS11757304

Manufacturer Part Number WPW10730972

Manufactured by Whirlpool

This is a manufacturer-approved replacement drain pump for your washing machine. To complete this repair you will need a 1/4 inch nut driver, 5/16ths nut driver, a flat blade screwdriver, and a pair of pliers. Make sure to disconnect power to the washer before beginning this repair.

This part works with the following brands: Maytag, Whirlpool, Kenmore, Inglis, Amana

This part works with the following products: Washer, Washer Dryer Combo

This part fixes the following symptoms: Will not drain | Pumps but will not spin | Noisy | Leaking

Videos For installing this part.

Questions & Answers
Sort by:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Installation Instructions Provided by PartSelect customers like you.
Average Repair Rating: 3.9 / 5.0, 31 reviews
What's this?
Sort by:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Andrew from St.Louis, MO
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Socket set
Parts Used:
WPW10730972
F 21 error
Removed the front panel unplugged
The washer drained water out, lift the washer up to un screw the drain pump. Then unhooked the hoses from pump put the other pump in.
338 of 373 people found this instruction helpful.
Was this instruction helpful to you?
Kurt from Caliente, NV
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers
Parts Used:
WPW10730972
water pump failed
Pump started making noises like ball bearings grinding. took the lower front cover off pulled the strainer out of the pump housing and found $2.55 in nickles dimes and quarters. Some 223 bullets and about 20 bobby pins. Together they had destroyed the impeller, so ordering a new one and installing it did the trick. Easy installation about 15mins.
79 of 84 people found this instruction helpful.
Was this instruction helpful to you?
Shawn from Clyde, NC
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers, Wrench set
Parts Used:
WPW10730972
Replaced Drain Pump on Whirlpool HE Duet Sport Washer
This do it yourself repair saved me the cost of a repair man's service call plus time to put it in. 1. First of all, make sure the unit is unplugged. On this type of front loading washer you will need to remove the bottom panel, which is secured by 3 nut screws. 2. Once the panel is removed you will need to use pliers to unscrew the drain plug and allow for excess water to drain out before removing the drain pump (get a pan or something that will fit underneath the drain). This is the area in which all the loose stuff, like coins and everything else falling out of pockets, gets trapped. The trap works well and needs to be checked periodically or if left unchecked it will probably be the cause of burning up the drain pump. 3. Once the water is drained you will need to use pliers to unsecure the two hoses attached to the drain pump. The pliers will pinch the wire clamps open and you can remove the hose easily. 4. The dryer is stacked on top of my washer and in order to get to the two screws holding the drain pump I needed to put a block of wood under the washer to give myself room to get a wrench to the screws. Once the dryer and washer were unloaded and nothing on top I was able to lift the washer and slide a block of wood underneath. 5. The pump has a power supply on the right hand side (a small white box with a wire attached) Remove the wire by gently pulling on the end of it. It is a plug type end. 6. Using a wrench (or socket driver) I took out the two screws (about an 1.5"). The drain pump slides to the right and out it comes. It is also secured by two rubber seals which are easy to remove as well as to install. 7. Now all you do is work backwards, installing the new drain pump by sliding the seals in place and wrenching the screws back in to hold the drain pump, followed by putting the two hoses back on with the pliers and placing the wire back into the power supply box on the drain. I would recommend anyone being able to do this on their own or at least with another person to help with a bit of lifting. The only way I knew to replace this part was because it was making all the noise, so it doesn't take much rocket science :)
68 of 71 people found this instruction helpful.
Was this instruction helpful to you?
Amy from Phoenix, AZ
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Socket set
Parts Used:
WPW10730972
water wasnt draining from tub/digital error msg
Took drain pump out and determined coins and practice ammunition are not good for drain pump rhesevior. Drain pump burnt up and froze. Part was easy to slide out and slide back in hooking up two hoses to it. Five minute fix!! Now we know where those rouge items went. Lol
37 of 42 people found this instruction helpful.
Was this instruction helpful to you?
Hong from Flushing, NY
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers, Screw drivers
Parts Used:
WPW10730972
Water leak under machine caused by cracked drain pump
Turn of the electrical power to the machine. I took off the cover on the machine below the door. You had to use phillips screwdriver to get the three screws out. In order to replace the pump I had to lift the washing machine about three inches up slightly over to one side (needed a strong person to lift as there was a dryer on top of it). The old pump has to be removed with a nutdriver as there are two nuts holding the pump in place under the machine ( I had to run out to the hardware store to buy a smaller one to fit under the machine as the big wrench was to big to fit under the machine). I unplugged the electrical connection to the pump. I unclamped the hoses attached to the pump using a plier, make sure you have something to hold water that will drain from the hose. I then push/pull the old pump to the right out of its place, it is attached to the metal at the bottom of the machine. I put in the new pump and tighten the screws on the bottom (this is the tricky part as you cannot see - a mirror may help). I also reattached the hoses and electrical connection. I turned on the machine to rinse to make sure there were no leaks before putting back the cover. Before throwing out the old pump, you can shake it and look in the opening of the old pump for any valuables left in pockets that may have washed out. I found a 18k bracelet, 25 cents and a small screw which may have caused the hole in the pump . Good luck :)
23 of 30 people found this instruction helpful.
Was this instruction helpful to you?
Dr. Merdad from Los Angeles, CA
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Socket set
Parts Used:
WPW10730972
draining problem
Open the bottom screws (hex-screw driver. remove riongs with pliers. use pan to remove excess water remained in pipes. pull to the right and remove. easier than it seems,
18 of 21 people found this instruction helpful.
Was this instruction helpful to you?
rick from ironton, OH
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers, Wrench (Adjustable)
Parts Used:
WPW10730972
I purchased the machine from a Scratch and Dent Place
The water pump housing was leaking due to some pre-existing damage and leaking on the floor. The repairman wanted 60.00 just to show up. I purchased a replacement pump from PartsSelect.com and installed it myself by taking off the bottom front panel (two screws on the bottom and unclamping the two hoses from the pump and the two screws holding the pump to the frame and then unsnapping the wiring coupler from the old pump. I pulled the old pump out through the front of the machine. I then installed the new pump and replaced the front cover. I saved myself a lot of money and everything went smoothly! The machine works great.
17 of 22 people found this instruction helpful.
Was this instruction helpful to you?
Tammy from Maryville, TN
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers
Parts Used:
WPW10730972
Would not drain
Removed bottom panel, removed hoses and pump. Reinstalled in reverse order.
12 of 18 people found this instruction helpful.
Was this instruction helpful to you?
max from dewitt, IA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Socket set
Parts Used:
WPW10730972
pump was not pumping
unhooked two water lines & electrical plugin unbolted old pump and installed new pump. took about 15 minutes.
10 of 15 people found this instruction helpful.
Was this instruction helpful to you?
Mary from Rehoboth, MA
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers, Wrench set
Parts Used:
WPW10730972
Leak in the pump housing from cracked plastic
Removed the old pump and installed the new one. Most difficulty came from the fact that the dryer is on top of the washer and the washer is inside a plastic pan that has a 2 inch lip which made it difficult to remover the front panel.
9 of 12 people found this instruction helpful.
Was this instruction helpful to you?
Customer Reviews
Average Rating:
36 Reviews
4.7
out of 5
Filter By Rating:
  • 5 Stars
    29
  • 4 Stars
    5
  • 3 Stars
    0
  • 2 Stars
    1
  • 1 Stars
    1
Sort by:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".

Model Cross Reference

This part works with the following models:

PartSelect Number: PS11757304
Manufacturer Part Number: WPW10730972
Brand
Model Number
Description
Kenmore
11041932510
Washer - COMMERCIAL WASHER
Kenmore
11041942710
Washer - WASHER
Kenmore
11046462500
Washer
Kenmore
11046462501
Washer
Kenmore
11046472500
Washer
Kenmore
11046472501
Washer
Kenmore
11047511700
Washer
Kenmore
11047511701
Washer
Kenmore
11047511702
Washer
Kenmore
11047512600
Washer
Kenmore
11047512601
Washer
Kenmore
11047512602
Washer
Kenmore
11047512603
Washer
Kenmore
11047512604
Washer
Kenmore
11047512605
Washer
Kenmore
11047531700
Washer
Kenmore
11047531701
Washer
Kenmore
11047531702
Washer
Kenmore
11047532600
Washer
Kenmore
11047532601
Washer
Kenmore
11047532602
Washer
Kenmore
11047532603
Washer
Kenmore
11047532604
Washer
Kenmore
11047532605
Washer
Kenmore
11047542600
Washer
Kenmore
11047542601
Washer
Kenmore
11047542602
Washer
Kenmore
11047542603
Washer
Kenmore
11047542604
Washer
Kenmore
11047542605
Washer