This part is able to sense the water level in the tub. When the water reaches the desired level, this switch stops the water from flowing in the tub and the washing program begins.
How Buying OEM Parts Can Save You Time and Money
Troubleshooting
This part fixes the following symptoms:
Will Not Start
This part works with the following products:
Washer.
Part# WPW10415587 replaces these:
AP6021127, W10156252, W10415587
Customer Reviews
Average Rating:
★★★★★
★★★★★
3 Reviews
4.0
Filter By Rating:
5 Stars
2
4 Stars
0
3 Stars
0
2 Stars
1
1 Star
0
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Gregory H - March 7, 2021
Verified Purchase
Simple. ANYONE can do this. Expensive part. But saved money on service call.
GE Profile generating F35 error code. Simple fix. Remove top/white plate by taking out 3 sheet metal screws. Slide panel BACK and out. Old part is located in top right back (as you face the front). Detach part by turning one quarter turn clockwise to pull out. Remove tube and electronic plug. Reattach wire clip and tube to new part. (I know. It's tight. Hardest part of process.) Reverse process to reattach; point tube connection to back (9 oclock), insert clip in hole, turn counter clockwise (6 o'clock) to snap/secure. DONE.
★★★★★
★★★★★
Robert F - May 23, 2019
Verified Purchase
pressure switch
the part didn't work we went with all the review that a F35 code was a faulty switch so we wasted $157.00 so either the part was faulty or it's something else
★★★★★
★★★★★
Timothy M - March 15, 2018
Verified Purchase
Water level sensor success
Part was perfect. It took 8 minutes to replace, fixing error code SUDS and F35
< Prev
1
Next >
Customer Repair Stories
Average Repair Rating: 4.8 / 5.0, 8 reviews.
What's this?
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
suds mesdsage apperared with f-35 error alert
Peace of cake! 3 screws at top of washer to gain access. Unplug sensor, but first have to rotate sensor 90 degrees to release from bracket. unplug black tiny hose and plug wire from sensor. Install new in reverse order. works great and saved a lot of cash doing it myself. Grateful for the info for the tips from other's w
... Read moreith same problem! Mark from Vermont Happy Camper:)))))))))
.
Read less
mark from MOUNT HOLLY, VT
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Screw drivers
4 of 4 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Getting “sud” or “F35” errors intermittently
Removed 3 screws from back of top panel, slid top off, twisted APS sensor 90 degrees, popped out of mount, removed hose and elect. connector, replaced with new APS sensor and reinstalled. Ran diag test, passed with no issues.
Dan from STOCKBRIDGE, MI
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
4 of 4 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Annalog Pressure Switch Failure (F35 error)
Replacing the switch was extremely simple - just attached the hose, snapped in the electrical piece and snapped the part onto the side of the washer!
Becky from Pollock Pines, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
7 of 8 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Suds and F35 error
Starting getting these errors...but we had also been washing about 300 towels a week from our gym for about 3 months. I contacted an ex-sears repairman friend of ours for advise. He first recommended checking the pump filter basket. It was easy to get to by taking off the front panel. It did have about three hand wipes and other debris in
... Read more it. Removing these items did cause the errors to occur less often, but they still did continue. We had our repair friend come over and go through the diagnostics checks as per the instruction sheet that was on the inside of the washer. It came down to being the pressure sensor. After replacing the sensor, the washer has worked flawlessly.
Read less
JOHN from BODFISH, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
6 of 8 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Receiving F35 error message after "sud"
After researching the issue on the internet, I found that this was a consistent problem with my washing machine model. Located Part Select, phoned them with the model of the machine and told them what I wanted. Part was received within 2 days. Flipped circuit breaker leading to washer off. Took top off of machine, located the pressure
... Read more switch, had to twist to remove where it was attached to side of machine. Removed plug with wires, plugged into new switch & replaced to previous location. Machine runs like a brand new one (the longest time was trying to figure out how to get the switch unattached from the side of the machine). Disappointed with Whirlpool; couldn't say enough good things about Part Select!
Read less
stephanie from haopkinsville, KY
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
10 of 16 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
f35 error code
removed 3 screws from back, then pulled hose of piece and disconnected wire clip. reassembled. have tu turn bottom of the piece torward you to remove from machine. this part is located on the back right side, black on my machine 1x2x2/4 inches in size, this is looking down into the wash machine from the front.
Nathan from Cincinnati, OH
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
6 of 8 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Had F35 and SUDS messages
Tried all the Internet fixes and nothing worked. Bough the part put it in and BINGO! problem fixed. This is a class-action suit waiting to happen -- will never buy Whirlpool again. The stink problem persists despite cleaning and more cleaning.
William from Gambrills, MD
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers, Screw drivers
10 of 12 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
sud code then F35 error code
Simply removed 3 screws from the back of the washer, twisted the part to the side to remove it from the slot it fit in. Removed the hose, them removed the wiring plug. Plugged in the wiring to the new switch, put the hose back, slid the switch in to the proper slot, twisted it into place, replaced screws and cut the washer on! BINGO!! Bee
... Read moren working like a dream.
Read less
Tim from Winton, NC
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
22 of 26 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
Next >
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
2 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Doug
November 29, 2018
I installed your new part & the problem persists i talk to one of agents he told me to contact Maytag but they don't have anyone to talk too. So i'm wondering what to do with this part if it is defective or if something else is wrong
For model number 5038193156
Hello Doug, thank you for your question. We would recommend checking the pressure hose to be sure it isn't kinked or clogged. Unplug the unit and wait about 5 minutes then plug the unit back in. The error code might reset. If it doesn't please call us and we can discuss the options. The part could be defective. I hope this helps!
Was this helpful?
Thank you for voting!
Allison
August 18, 2023
My front loader starts up but keeps having the suds error come up.
For model number MHWE500VP00
Hello Allison, thank you for asking. According to or research, the sud error indicates that the washer detected too many suds during the cycle, and your load may not be thoroughly rinsed, or water may not be entirely removed. You may want to select a rinse/spin cycle for further rinsing. If the issue still occurs, you may need to check the drain hose, part number PS11747970, to fix the issue. We hope this helps!
