This bake element is found on the bottom of the oven. his bake element is for ranges.
The bake element is at the bottom of the oven and supplies the heat for baking.
Unplug the range or shut off the house circuit breaker for the range before installing this part. Wear work gloves to protect your hands.
How Buying OEM Parts Can Save You Time and Money
Troubleshooting
This part fixes the following symptoms:
Element will not heat | Little to no heat when baking | Oven not heating evenly
This part works with the following products:
Range.
This part works with the following products:
Jenn-Air, Whirlpool, Maytag, Amana.
Part# WPW10310274 replaces these:
AP6019234, 74010883, 7406P439-60, W10310274
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
11 questions answered by our experts.
< Prev
1
2
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Gary
August 16, 2017
I just ordered a new baking element for my Maytag oven. The old one had broken in two. I knew to expect both rear terminals to be attached to wires coming from the two holes in the rear of the oven. However only one terminal was connected to a wire. I was very careful when i pulled the old element out so as to not "lose" the wires through to the back of the unit. I also felt way back into the hole and could not find any wire. Is there any possibility that this element has electricity to only one terminal??
Hello Gary,
Thank you for your question.
Your oven element would require two wires to complete the circuit. You may need to remove the back panel on your unit to see if you can locate the second wire. It is possible the terminal connection may have come off as the broken element was being removed. The wire can fall quite far down as the only thing securing them in place is the terminal connection itself.
I hope this helps!
9 people found this helpful.
Was this helpful?
Thank you for voting!
Dan
October 19, 2017
Oven on bake only heats to about 200 degrees, does that mean i need to replace the bake element ?
For model number JES9705BAS
Hi Dan,
Thank you for your question. It could be your bake element. I could also suggest testing your over temperature probe as well. You can test both of your parts with a multi meter. Good luck with your repair.
2 people found this helpful.
Was this helpful?
Thank you for voting!
Laura
March 27, 2019
Our Jenn-Air electric smooth top downdraft slide-in range is 12 -years-old, and it seems like the heating element is no longer working, as it only heats to 198. When I called the dealer from whom we purchased it, a customer care rep. said there are no longer parts for this range. When looking it up on your site, it seems as though we found the heating element. The model number: (p) jes9900bas serial number: (s) 12724095jp
For model number JES9900BAS
Hello Laura, thank you for inquiring. For your model the Bake Element is part PS11752540 and the Broil Element is part PS11744519.
2 people found this helpful.
Was this helpful?
Thank you for voting!
Tom
November 24, 2019
On preheat cycle only top element is heating and then when temperature is reaching (to fast) only top element is working causing top cooking burning. This cause can to due to baking under element?
For model number JES9900CCW00
Hello Tom, Thank you for the question. If the bottom element is not turning on during or after the pre-heat, it will need to be replaced. You can verify it is defective by checking for continuity with a multi meter. Hope this helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Tom
November 24, 2019
What is the resistance value of bake element?
For model number JES9900CCW00
Hello Tom, Thank you for the question. A bake or broil oven element's resistance may be in the area of 20 to 40 ohms. Hope this helps!
Was this helpful?
Thank you for voting!
Tom Bamrounsavath
November 25, 2019
Hi, my oven element seem ok 20 homs. But during preheat cycle it’s seem not working only broil element works the oven element not become red but lukewarm... what is the trouble? relay on electronic board? best regards,
For model number JES9900CCW00
Hi Tom, please read our guide here: https://www.partselect.com/Repair/Range-Stove-Oven/No-Heat-When-Baking/. Thank you for your question and good luck with your repair!
Was this helpful?
Thank you for voting!
Pam
May 9, 2022
Oven element does not adequately heat nor hold heat. Has bright red spot in one portion of element. Has one side that looks like it is degrading. Have no idea how old appliance is, but maybe original to house built in 1992.
For model number JES9750CAS01
Hi Pam,
Thank you for your question. If the broil or bake element shows signs that they are degrading, they will need to be replaced. The part number listed under your model number for the broil element is PS11744519. The part number listed for the bake element is PS11752540. If you need help placing an order for these parts, customer service is open 7 days a week and anyone will be happy to assist you. Please feel free to give us a call. We look forward to hearing from you!
Hello Mary, thank you for reaching out. You can easily remove and install the bake element by using the following steps:
1. Unplug the range.
2. Disconnect the wires.
3. Remove the oven rack.
4. The bake element is present at the bottom of the oven.
5. Remove the 2 screws holding the bake element to the stove.
6. Remove the old bake element and install the new one.
7. Align the new bake element to the screws and tighten them.
We hope this helps, good luck with this repair!
Was this helpful?
Thank you for voting!
Charles
March 15, 2023
Instructions on how to replace the Bake Element.
For model number JES9800CAS02
Hello Charles, thank you for reaching out. You can easily remove and install the bake element by using the following steps:
1. Unplug the range.
2. Disconnect the wires.
3. Remove the oven rack.
4. The bake element is present at the bottom of the oven.
5. Remove the 2 screws holding the bake element to the stove.
6. Remove the old bake element and install the new one.
7. Align the new bake element to the screws and tighten them.
We hope this helps, good luck with this repair!
Was this helpful?
Thank you for voting!
Mark
November 15, 2019
My oven preheats to the correct temp while in the bake mode but does not maintain this temp throughout the cooking process. I will check the temp in the oven and realize that it feels cooler and then i'd put the oven into a preheat mode and in fact find the temp is 75-100 degrees below the set point.
For model number JDS9860BDB
Hi Mark, test the bake element PS11752540 and bake thermostat PS1570174. More than likely one of these part is the cause of the problem. Thank you for your question and good luck with your repair!
Average Repair Rating: 4.4 / 5.0, 11 reviews.
What's this?
< Prev
1
2
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
bake element non operational
No instructions with part, so I had to look up on internet. This took more time than installing it. Think basic instructions should come with the expensive part.
Charles from Sneads Ferry, NC
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
1 personfound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The electric element in the oven broke
Shut off breaker, assure zero energy. Using phillips screwdriver remove old element, unplug wires from element. Reconnect wires to new element, secure screws. Assure all tools removed and people are clear before re-energizing power to range. I was not happy with the packaging, the new element came in a box with no protective packing material!
richard from hamilton, NJ
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Socket set
2 of 2 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven would not heat past 200
First be sure to unplug stove or turn off from breaker switch. I Removed racks from oven . Using screwdriver I loosened the back plate in the oven that held the wires connected to heating element , being careful not to let wires fall through holes . Gently pull element tip apart from wire. Snap end of new element to wires, screw plates back to tighten Turn oven on and check to assure heating properly. Very simple
Desmona from GONZALES, LA
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
3 of 3 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Burned out lower oven element replacement
SHUT OFF POWER AT BREAKER BOX! Remove oven door, use nut driver to remove two screws holding old element to back of oven. Pull forward to get wires into oven, remove wire clips from old part and re-attach to new element using pliers. Re-attach to back of oven, replace door. Turn on power and heat oven to burn off coating on new element. Not at all difficult, except for wire clips are at angle to wire, making re-attachment a bit difficult to do. DO NOT LOSE WIRES INTO BACK AS THEY WOULD BE VERY DIFFICULT TO RESCUE IN A JENN-AIR SLIDE IN UNIT LIKE OURS.
Lynn from MENOMONIE, WI
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers
2 of 3 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Lower range burner element burned out
Should have been under the 'very easy' category, unscrew 2 screws, pull out old element, disconnect wires, reconnect new wires and screw back in. Unfortunately the right wire disconnected while pulling out the element, so I had to pull the the stove out, disconnecting vents in the process, then remove the back to be able to feed the wire back in thru the element hole . While back here I noticed that the reason the wire came off is that the way it was routed behind the stove cover was such that there was virtually no slack to be able to pull the element out in the first place. I'll bet that at the factory, the element was installed first, THEN the wires were connected. Whoever was on the line that day made extra sure of no slack in back, and that made the job take 5-6 times longer than it should have. As for the part replacement, it was a perfect match to the original part so it was super easy once the wire got back in the oven...
Andrew from SAINT PAUL, MN
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers
6 of 7 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
My old element finally went out
Easy peasy...1. Take 2 screws out to remove the back cover. 2. Unplug the 2 wires from the element. 3. Remove the 2 screw holding the element from inside the oven and take out the old element. Repeat the steps above in reverse order.
Ricky from JASPER, TX
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
6 of 6 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Bake element failed
Removed 2 screws holding element to stove then gently pulled element forward to exposed lead connections and disconnected leads to element then reconnected leads to new element and gently pushed element ends back into the openings in the back of the stove and replaced screws to hold element to stove
Christopher from Daphne, AL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
18 of 21 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Bake element blew up
took the old one out (two phillips head screws)and put the new one in. done. took about 5-6 minutes.
Kevin from Norfolk, VA
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
4 of 7 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
needed new element. Old one burnt in two
unscrewed and unplugged the old one and plugged in and screwed in the new one. EASY!
Elaine from Orfordville, WI
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers
26 of 35 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
bake element needed replacement
replacement was very easy, took 5 min
svetlana from chicago, IL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
4 of 7 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
2
Next >
Customer Reviews
Average Rating:
★★★★★
★★★★★
42 Reviews
4.9
Filter By Rating:
5 Stars
37
4 Stars
4
3 Stars
1
2 Stars
0
1 Star
0
< Prev
1
2
3
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Patrick M - June 12, 2023
Verified Purchase
easy repair for average dyier
receiving the part took awhile ,other than that everything was good
★★★★★
★★★★★
Ben J - May 6, 2023
Verified Purchase
Easy replacement took 5 min
Fast delivery and easy to fix
★★★★★
★★★★★
Harold W - April 12, 2023
Verified Purchase
Went well...
The oven bake element arrived in perfect condition. Took only a few minutes to install. Is working well. Oven temperature is right on the mark as set.
★★★★★
★★★★★
James R - March 28, 2023
Verified Purchase
As advertised
It was in good condition. Received on time, worked as intended.
★★★★★
★★★★★
Mary M - January 9, 2023
Verified Purchase
Excellent service
The part arrived very quickly; unfortunately, it had a defect. I contacted customer service and they immediately sent me a replacement, which took me only about 2 minutes to install. Great service and I would shop there again because they stand behind the products they sell.
★★★★★
★★★★★
Dwight B - January 1, 2023
Verified Purchase
Bake element
This part fit my oven and it came fast
★★★★★
★★★★★
Beverly K - May 10, 2022
Verified Purchase
Part was easy to install (within 15 minutes).
I used clamps to hold the two element wires within the oven until I could reconnect the new element.
★★★★★
★★★★★
Karin E - December 2, 2021
Verified Purchase
right part
it was the right part, and my stove was back working in time for Thanksgiving
★★★★★
★★★★★
Denis A - November 19, 2021
Verified Purchase
Fast delivery, works good.
Very satisfied.
★★★★★
★★★★★
John L - September 7, 2021
Verified Purchase
Great Service
Part arrived quickly and in good condition. Thank you.
< Prev
1
2
3
Next >
Model Cross Reference
This part works with the following models:
PartSelect Number: PS11752540
Manufacturer Part Number: WPW10310274
With the Fix app, you can quickly and easily find information on your appliance, along with videos and articles to help you fix it.
"Like magic. I took a picture of the model number on my refrigerator, and the app identified it right away … Very convenient. I'm impressed." ★★★★★ - Clever Jeff
★★★★★
You added 1 item to your cart
✖
$
Qty:
Total item(s) in cart:
Order Subtotal
$
*Taxes and shipping will be applied during checkout
Your Subscriptions
