Whirlpool/Whirlpool_Thumb/MFQAB0Y8.gif
See part 20 in the diagram

Get in touch, we're here to help!

Open until 12am EST

customerservice@partselect.com

Water Level Switch

$80.44   In Stock

Get this part fast. Average delivery time via standard shipping: 1.8 days.

PartSelect Number PS11752436
Manufacturer Part Number WPW10304342
Manufactured by Whirlpool
Troubleshooting
This part works with the following products:
Washer.
This part works with the following products:
Whirlpool, Maytag.
Part# WPW10304342 replaces these:
AP6019132, W10304342
Questions and Answers

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

Customer Repair Stories
 Average Repair Rating: 3.3 / 5.0, 1 reviews. What's this?
    Sort by:
    Sorry, we couldn't find any existing installation instruction that matched.
    FO8 and EO3 fault codes. See your manual.
    To replace the water level switch is easy, remove the three screws in the rear, slide top back a couple of inches, lift cover off. Rear upper right corner is the switch. Remove small hose to switch, twist switch 90* and pull out, disconnect two connectors, reverse procedure to install new switch. This did not fix the code problem tho. To get to the pump filter is not very difficult but time consuming. Disconnect the power cord. Remove the soap dispenser, then the two screws behind it, then two screws for the front control panel, then four screws on the bottom of the front cover, back out but leave in the three screws on top of front cover, two screws holding the door lock and switch, careful with that, wires are short and difficult to plug back in, remove water spout from drum seal , lift out the bottom of front cover, the seal holds it in, reach in lying on the floor, the filter is in the center, make sure the washer is empty or water will run out, unscrew filter. I found a fabric eyeglass holder and a $1.94 in coin. This tells me the seal to drum is to far away. Reverse procedure to put back together. I will never buy another front loading Washer again. They don't appear to get enough water to really do a good wash job no matter what cycle you use. If you should pull the seal off close to the drum , it's difficult to fasten back on again.
    • William from DELPHOS, OH
    • Difficulty Level:
      Easy
    • Total Repair Time:
      30 - 60 mins
    • Tools:
      Nutdriver
    3 of 3 people found this instruction helpful.
    Was this instruction helpful to you?
    Thank you for voting!
      Model Cross Reference
      This part works with the following models:
      PartSelect Number: PS11752436
      Manufacturer Part Number: WPW10304342
      Brand
      Model Number
      Description
      Whirlpool
      BNQ11C6ANA0
      Washer
      Whirlpool
      BNQ11CVANA0
      Washer
      Maytag
      MHW6000XG0
      Washer - WASHER
      Maytag
      MHW6000XG1
      Washer - AUTOMATIC WASHER
      Maytag
      MHW6000XG2
      Washer - AUTOMATIC WASHER
      Maytag
      MHW6000XR0
      Washer - WASHER
      Maytag
      MHW6000XR1
      Washer - AUTOMATIC WASHER
      Maytag
      MHW6000XR2
      Washer - AUTOMATIC WASHER
      Maytag
      MHW6000XW0
      Washer - WASHER
      Maytag
      MHW6000XW1
      Washer - AUTOMATIC WASHER
      Maytag
      MHW6000XW2
      Washer - AUTOMATIC WASHER
      Whirlpool
      WFW94HEXL0
      Washer - Residential
      Whirlpool
      WFW94HEXL1
      Washer - Residential, Automatic
      Whirlpool
      WFW94HEXL2
      Washer - Residential, Automatic
      Whirlpool
      WFW94HEXR0
      Washer - Residential
      Whirlpool
      WFW94HEXR1
      Washer - Residential, Automatic
      Whirlpool
      WFW94HEXR2
      Washer - Residential, Automatic
      Whirlpool
      WFW94HEXW0
      Washer - Residential
      Whirlpool
      WFW94HEXW1
      Washer - Residential, Automatic
      Whirlpool
      WFW94HEXW2
      Washer - Residential, Automatic

      Get in touch, we're here to help!

      Open until 1am EST

      Contact Customer Service