Dishwasher Door Latch w/Switches No Handle Specifications
This door latch, used in dishwashers, is located at the top of the door and locks the door shut when the dishwasher is working. If the door will not close or is damaged, changing the latch could be the solution. For this repair, remove all screws from the inner panel, then lift up the inner door panel and hold the door apart. Next, access the latch and pull wires from the switches. Refer to the manual provided by the manufacturer for further instructions and guidance. Remember to unplug the dishwasher from the power source or shut off the house circuit breaker before beginning this installation project.
The door didn't seal tight. So when it would go into rinse mode it would leak water on my floor
The repair went easy. Just unscrewed the inside door panel and latch assembly. Then put the new one in. The only bad thing was I purchased the latch assembly with out the handle and found out mine was cracked. I looked back on-line and couldn't find just the handle. Everybody sold it with the latch assembly. I thought I would save the 2 b
... Read moreucks buying the assembly without the handle. But in the end the door seals tight and no water leaks.
Read less
robert d from MOORHEAD, MN
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
1 personfound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The door latch broke
It was very simple and easy. I opened the panel inside the door; total of 8-10 screews. The latch has two electrical connections and switches. The replacement part I got came with an extra set of switches. Replacing the switches needed an electrical tool which I don't have so I decided to keep the old ones. It is quite easy to take out th
... Read moree switches and replace the latch. I should have taken out the power; but I did not. I was just careful handling the wires et al; no big deal either. My dishwasher is working fine now. I was able to fix it within $40 and 1 hour of effort. Any technician would have cost me atleast couple of hundred bucks + parts etc.
Read less
Talha from Summit, NJ
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
1 of 2 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Unit would not turn on.
After checking the door switch I found the micro switches were working but the unit would not start on the control panel. Thinking the latch was worn, I ordered a replacement. After changing the replacement latch and switches that came with it, the unit would still not start. I checked the switch and it is making contact. I can start the
... Read moreunit after I close the door using the handle of a pair of pliers. So I assume the control board is bad, due to the fact that it will not initialize the control panel until the door is closed. Now I have ordered a control board and will replace...stay tuned!!
Read less
Lloyd from Denver, NC
Difficulty Level:
A Bit Difficult
Total Repair Time:
More than 2 hours
Tools:
Nutdriver, Pliers, Screw drivers
0 of 1 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door would not close - latch broken
1. Turned off power. 2. Unscrewed ten screws holding inside of door in place. 3. Lifted cover enough to access latch - helpful to have someone to hold this while doing the job. 4. Disconnected old latch assembly on each side - this was the hardest part as they were stiff and needed to be pulled hard. 5. Attached new latch assembly. 6
... Read more. Screwed door panel back on. 7. Switched power back on. So easy and saved about $150. This stuff is NOT HARD and I just wish more people had the gumption to do repairs themselves instead of paying 'experts' to do exactly the same job.
Read less
Mandy from Lafayette, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
0 of 1 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door det not lock
Replase door lach Thang you for the fast respons Peter Hansen
peter from redondo beach, CA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
0 of 1 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door handle stopped engaging
First I watched the repair video provided at your site. Once I got the right part, it went like a breeze. Just a phillips head screw driver and 5 minutes of my time. Speaking if the right part.... I would suggest that you remove the 'LATCH-DOOR-NO Handle' from your parts list.It only cause confusion in ordering the part I needed, and a lo
... Read moress of several days time in the repair cycle. All in all, a good repair experience. I would reccommend you to my " Do It Yourself" friends. Thanks, Harold L.
Read less
Harold L. from winamac, IN
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
4 of 5 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door would not shut
Easy! Unscrewed panel, took off old latch, put on new. Took about five minutes.
Laura from Chester, NH
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
1 personfound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
plastic part was worn out
the small plastic part that turns the dishwasher off and on when the door is shut was worn out. It was really easy to change out. I unplugged the power cord and removed the black and white wires. Put in the new switch and it was ready.
Eduardo from Whittier, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
0 of 1 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
2
3
Next >
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
45 questions answered by our experts.
Sort by:
< Prev
1
2
3
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Gary
December 18, 2017
I need a new door handle for this dishwasher.What is the part # ?
For model number ADB1500AWS3
Hello Gary, Thank you for your inquiry. The part number for the door handle with switches is WPW10130695. Hope this helps!
12 people found this helpful.
Was this helpful?
Thank you for voting!
Jason
January 16, 2018
Needing door ( handle ) latch for this model in black. What is the part #
For model number DDB1501AWZ
Hi Jason,
Thank you for your question. The part number for the black door handle and latch assembly with switches for your dishwasher is PS11731673. I hope this helps. Thank you and have a great day!
7 people found this helpful.
Was this helpful?
Thank you for voting!
Laurie
March 9, 2018
I need to order the door handle, i ordered the door latch w10275768, but i'm not sure what the handle part # would be, can you help?
For model number Maytag Quiet Series 300
Hello Laurie, thank you for writing. The door handle is not sold separeately. You would want to order the Dishwasher door latch and handle assembly part number WPW10130695. I hope this helps!
7 people found this helpful.
Was this helpful?
Thank you for voting!
Ken
August 8, 2017
How to remove old broken latch
Hi Ken,
First and foremost, make sure to unplug your appliance and turn off the water supply. You will have to remove all of the screws holding the inner door panel to the outer door panel. You should then be able to pop off your old latch. If the wire harness is hard to remove from your latch you can use a flat head screw driver to help push the plugs off of the old terminals. Make sure to replace your handle as this part does not come with your handle already attached. After you have done that, just follow these steps in reverse to put your appliance back together. I hope that helps!
6 people found this helpful.
Was this helpful?
Thank you for voting!
Juan
October 4, 2017
Is it possible to get the handle and not the entire switch
For model number adb1200awq
Hi Juan,
Thank you for your question. Unfortunately no. You have to get the handle with the entire latch assembly. I have linked the correct part below for you. Good luck with your repair.
I am searching for a door latch for my dishwasher. Can you help with this?
For model number ADB1500AWW0
Hi David,
Thank you for your question. The door latch you have referenced in your question to us is the correct part for your appliance. If you need the door handle and latch assembly with switches the part number for it is PS11748729. I hope this helps. Thank you and have a great day!
3 people found this helpful.
Was this helpful?
Thank you for voting!
Dave
January 22, 2019
Hello,
For the jdb1250awp, should i get the ps11751688 or ps11748729 (with the handle) will also work? Thx a lot
For model number Jenn-Air JDB1250AWP
Hello Dave, thank you for your question. We would recommend ordering the latch with handle part number PS11748729. I hope this helps!
2 people found this helpful.
Was this helpful?
Thank you for voting!
William
January 31, 2019
Need part#w10275768 with handle. Do you sell them together or do i have to order separate?
For model number Mdc4650awb3
Hello William, thank you for your question. We do have the handle and latch assembly. That part number is PartSelect Number PS11748729. Its best to order the assembly, as it has been redesigned to be more effective. Please enter the part number into the site for current price and availability. Good luck with your repair!
2 people found this helpful.
Was this helpful?
Thank you for voting!
Shaun Prediger
May 7, 2019
Looking for a part to replace the handle assy.
For model number Maytag-Quiet Series 300, MDB7600aWS
Hello Shaun, thank you for inquiring. For your model the Door Handle and Latch Assembly with Switches is part PS11748729.
2 people found this helpful.
Was this helpful?
Thank you for voting!
Angela
October 18, 2023
Does this come with the handle?
For model number WPW10275768 or MDB7600AWW
Hello Angela, thank you for the question. The handle is not included with this part. For your model, the door latch and handle assembly is part number PS11748729. We hope this information is useful!
