This part ensures that your door stays locked while the machine is running.
How Buying OEM Parts Can Save You Time and Money
Part Videos
Replacing your Whirlpool Washer Door Lock Latch
Troubleshooting
This part fixes the following symptoms:
Will Not Start | Lid or door won’t close
This part works with the following products:
Washer.
This part works with the following products:
Whirlpool, Kenmore, Maytag, Inglis.
Part# WPW10253483 replaces these:
AP6017910, 8540222, 8540772, W10253483
Customer Reviews
Average Rating:
★★★★★
★★★★★
3 Reviews
4.7
Filter By Rating:
5 Stars
2
4 Stars
1
3 Stars
0
2 Stars
0
1 Star
0
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Ronald M - September 2, 2018
Verified Purchase
Door Lock Latch Repair.
Was like the video said. Installed in less then 20 minutes...
★★★★★
★★★★★
Gregory H - April 3, 2018
Verified Purchase
Washer door lock
Part was correct and worked great. Easy to install.
★★★★★
★★★★★
Daniela R - March 27, 2018
Verified Purchase
It solved the issue with F22.
I received the part very fast. It was exactly the same model that I had. It worked great and solved the problem of my washer (error F22).
< Prev
1
Next >
Customer Repair Stories
Average Repair Rating: 3.0 / 5.0, 2 reviews.
What's this?
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
the latch broke on my front loading washer.
My son did the repair.So I just know he got it working.Also the part I order came the next day after I called.And if I ever need another part for any of my other appliance I will be sure to call you.And I have told other people I know about you Thanks alot.Deborah Gaffney
Deborah S from Connellsville, PA
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Screw drivers
34 of 49 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door latch module was defective
This model is a front-loading washer. The spring loaded retainer for the front of the boot must be removed, then the boot can moved to the side exposing the module. Remove the two screws holding the model, pull the model out, remove the three electrical plugs, then reverse this procedure to install new module.
Carlton from Greer, SC
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Pliers, Screw drivers
95 of 113 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
Next >
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
13 questions answered by our experts.
Sort by:
< Prev
1
2
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Barb
September 5, 2019
Washer starts and fills but once it starts to spin it blinks a red light (door lock) and stops running. Can get it to open and sometimes it'll finish the load but the problem seems to be getting worse. It doesn't seem to matter what size of load we put it.
For model number WFW9750WW001
Hello Barb, Thank you for the question. This sounds like the Door Lock is defective and needs to be replaced. Hope this helps!
12 people found this helpful.
Was this helpful?
Thank you for voting!
Chris
September 14, 2017
The washer stopped in the middle of a cycle and wouldn't unlock. Finally unlocked, now the washer won't start. Makes noises as if it is trying to lock but light doesn't come on like it used to. I put it in diagnostic mode, but it didn't seem to move past testing the lock mechanism (kept flashing on rinse/spin). No error codes displayed. Is the latch on the door supposed to move around a little or should it be very tight? Thank you!!!!!!
For model number wfw8410sw03
Hi Chris,
Thank you for your inquiry. There are a few parts you will need to check to see which one is causing the issue. You will need to check the door lock latch, the temperature sensor, the drain pump, the door strike, the drive belt and the dispenser actuator switch. I hope this helps. Thank you and have a great day!
4 people found this helpful.
Was this helpful?
Thank you for voting!
Dave
February 28, 2020
How do i test this door lock assembly to make sure it’s what is causing my problems?
For model number WFW9151YWOO
Hello Dave, thank you for inquiring. You can test the resistance of the Door Lock Latch with a multimeter. The wax motor in the Door Lock Latch should test as around 1500-1750 ohms to be working properly.
4 people found this helpful.
Was this helpful?
Thank you for voting!
Mackenzie
February 18, 2020
Hello, we have already bought the latch to replace our old one on our Kenmore 110.47571601 but the #20 torx screw with built in washer for the latch is stripped and cannot be reused. Do you sell this screw?
For model number 110.47571601
Hello Mackenzie, thank you for your question. The screw that holds the latch for this unit is PartSelect Number PS11746286. I hope this helps.
When i close washer door it beeps twice but won't start. After slamming door a few times, it may start. Is this a cause of the door latch not functioning properly?
For model number WFW8300SW00
Hello Luz, thank you for inquiring. Yes, this may be due to a faulty Door Lock Latch, this part number PS11751211 for your model washer. You can test the resistance of the Door Lock Latch with a multimeter. The wax motor in the Door Lock Latch should test as around 1500-1750 ohms to be working properly. You may also want to consider the Temperature Sensor, part number PS11755214 as the cause. Good luck with your repair!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Gary
September 23, 2021
Washer has power, fills with water but, has no spin. The belt is good.
For model number MHWE251YG00
Hi Gary,
Thank you for your question. If your washer will fill with water but not spin, there are some parts that you will need to check to see which one is causing the issue. You will need to check the pump, the door lock latch and the belt. You will find the information on how to test these parts under Free Repair Help and Instant Repairman on our website. We hope this helps! Good luck with the repair!
This part doesn’t look the same as the one in my washer. I’ve replaced the motor control and only get 3 beeps. I would like to test this which tabs are the wax motor. The DC , AC or the ones marked 1 2 3 at the top.
For model number 110.47081600
Hello Kevin, thank you for your question. Did you see the Latch PS11745083?. We have a video for you to access. If you need help placing an order, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you.
Hi, for part # WPW10253483 washer door lock switch, there are 3 terminals I believe for 2 coils and one for common, what is the resistance value of these terminals for me to tell that I had a defective switch? Reading I had for left and right terminal @2k ohms: .119 ohms; Left to middle: .058 ohms: middle to right terminal: .062 ohms.
For model number Maytag MHWZ600TE00
Hi Henry,
Thank you for your question. You can test the resistance of the Door Lock Latch with a multimeter. The wax motor in the Door Lock Latch should test as around 1500-1750 ohms to be working properly. If you have any questions, please let us know. We are open 7 days a week. We look forward to hearing from you!
1 person found this helpful.
Was this helpful?
Thank you for voting!
BRAD
July 12, 2023
My machine runs normally but will not start the final spin leaving the clothes very wet. I have checked the drain pump and hoses and all are free and clear. The machine gives me the code F0 E1. I cannot find this code in the failure error codes that came with the machine. Could it be a problem with the door not locking. It makes a noise when started that sounds like it is locking.
For model number YMHWE201YW00
Hi Brad, thank you for contacting us. We have researched the model and would suggest making sure you are not running the clean washer cycle when the clothes are in the drum. Unplug the washer for 5 minutes and then plug it back on. If the error still appears, the issue might be with the control board, part number PS11753744. It processes the cycle settings you choose. We hope this helps!
Hello William, thank you for the question. It appears that your washer may have a damaged door lock, part number PS11751211. We recommend checking it to get to the root of the problem. Good luck with this repair!
Was this helpful?
Thank you for voting!
< Prev
1
2
Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
