Maytag/Maytag_Thumb/59440.gif
See part 1 in the diagram

Get in touch, we're here to help!

Open until 10PM EST

customerservice@partselect.com

Control Panel with Touchpad - Stainless/Black

★★★★★
★★★★★
1 Review
$360.39   In Stock

Get this part fast. Average delivery time via standard shipping: 1.8 days.

PartSelect Number PS11750321
Manufacturer Part Number WPW10206064
Manufactured by Whirlpool
Troubleshooting
This part works with the following products:
Range.
This part works with the following products:
Jenn-Air.
Part# WPW10206064 replaces these:
AP6017026, 74011578, W10206064
Questions and Answers

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

3 questions answered by our experts.
    Sort by:
    Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
    Tom
    April 12, 2018
    I am replacing the control panel ps11750321. And I cannot figure out how to detach the burner led modules from the panel being removed.
    For model number JES9900BAS
    Hi Tom, Thank you for the question. The ribbon cable wire harness should just pull off the control panel. Grip end side of the connector and pull out. Hope this helps!

    1 person found this helpful.

    Was this helpful?
    Thank you for voting!
    Kay
    January 12, 2020
    The control panel stopped working, can we replace it ourselves? Is there a video, or do we need to call a repair man?
    For model number JES9900BAS
    Hi Kay, Thank you for your question. We do not have information specifically for this model on how to replace the control panel, but here are some installation instructions on how to replace a burner switch that may help. It involves removing the control panel to access the switch. Unplug the oven from the electrical outlet. Remove the four screws under control panel. Remove the old burner knob and loosen the old burner control. Lower control panel from the range. Remove the 5 wire connectors from old burner control with pliers. Remove the 2 screws that held burner control to the range panel. These are Torx head screws. Install new burner control. Replace the two screws to burner control. Replace the 5 wire connectors to new burner control. Replace the 4 screws under the panel. Replace the knob to new burner control. Restore power to the oven and it should now work for you. If you require more information there are videos on YouTube that you may reference or you will need to contact the manufacturer. We hope this helps. Thank you and have a great day!

    1 person found this helpful.

    Was this helpful?
    Thank you for voting!
    Tim
    July 3, 2019
    Our number pad on the control panel does not work, exhaust fan switch does not work,and rapid heat switch does not work. Top burners do work, and the bake 350 or 375 switch does work. Broil switch does work. Tried replacing the oven control part #ps11745985. We still have the same problems. Do we need to replace the control panel? Do you have any suggestions?
    For model number JES9900BAS
    Hi Tim, thank you for your question. That may be the part that would be the issue. Especially if you have changed your control board itself. You could do a quick check on all of the other parts. Test your elements with a multi meter to see if they are working correctly or not. They should be reading between 0 - 50 ohms to be working correctly. The other part you should check would be your oven temperature sensor. That can also be tested with a multi meter and should be reading between 1000 - 1100 ohms. However if all of those parts are find then it is likely your panel that was the issue. Good luck with your repair.

    Was this helpful?
    Thank you for voting!
      Customer Repair Stories
       Average Repair Rating: 3.8 / 5.0, 1 reviews. What's this?
        Sort by:
        Sorry, we couldn't find any existing installation instruction that matched.
        touchpad malfunction
        It was obvious to see that the front plate that was attached to the sub frame allowed over spill from the glass range top to seep through the joint thus allowing the liquid to disrupt the electric harness cable causing it to carrode.
        I used high heat silicon to seal the joint accross the entire top preventing further problems of future over spills.
        • Stephen from South Hadley, MA
        • Difficulty Level:
          Really Easy
        • Total Repair Time:
          30 - 60 mins
        • Tools:
          Nutdriver
        • Parts Used:
          WPW10206064
        15 of 23 people found this instruction helpful.
        Was this instruction helpful to you?
        Thank you for voting!
          Customer Reviews
          Average Rating:
          ★★★★★
          ★★★★★
          1 Review
          5.0
          Filter By Rating:
          • 5 Stars
            1
          • 4 Stars
            0
          • 3 Stars
            0
          • 2 Stars
            0
          • 1 Star
            0
            Sort by:
            Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
              Model Cross Reference
              This part works with the following models:
              PartSelect Number: PS11750321
              Manufacturer Part Number: WPW10206064
              Brand
              Model Number
              Description
              Jenn-Air
              JES9900BAS
              Range
              Jenn-Air
              JES9900BAS20
              Range - 30" SLIDE-IN ELECTRIC RANGE
              Jenn-Air
              JES9900BCS
              Range
              Jenn-Air
              JES9900BCS21
              Range - 30" SLIDE-IN ELECTRIC RANGE

              Get in touch, we're here to help!

              Open until 10PM EST

              Contact Customer Service