Ice Maker Assembly WPW10190981

Hello Clara, thank you for your question. The ice bucket and auger is what holds the ice and pushes ice down into the door. If the part you need is in the door itself, and is the chute that allows ice to come down from the door that part number is WP13005703B. I hope this helps!

Hi Doug, Thank you for your inquiry. Open both refridgerator doors, depress the release button on the side of the ice bin and pull it out. Insert a small flat head screwdriver into the side cover access hole and press down to release the locking lever, then pull the side cover forward to remove. Use the screwdriver to press the retaining tab to release the ice maker assembly and pull it forward. Disconnect the wire harness and remove the entire assembly. Use a large flat head screw driver to pry the cover off, and use a 1/4 inch socket or nut driver to remove the bolt securing the sensor wire bracket at the front and detach the bracket. Disconnect the wire harness and remove the bolts securing the ice maker to the baffle on the bottom. Pull the ice maker out and remove the thermal fuse. Although we do not have an exact video for this part, we have included a link to a video for a similar part to assist you. Good luck with your repair. https://www.youtube.com/watch?v=hmCE3oKpEk0

Hello Tom, thank you for your question. Open both refrigerator doors, depress the release button on the side of the ice bin and pull it out. Insert a small flat head screwdriver into the side cover access hole (cover at the bottom left under the icemaker) and press down slightly to release the locking lever, then pull the side cover forward to remove. Use the screwdriver to press the retaining tab on the left side of the icemaker to release the ice maker assembly and pull it forward about half way. With the wire harness disconnected, the icemaker should slide right out. I hope this helps.

Hello Raelynn, Thank you for your inquiry. Open both refridgerator doors, depress the release button on the side of the ice bin and pull it out. Insert a small flat head screwdriver into the side cover access hole and press down to release the locking lever, then pull the side cover forward to remove. Use the screwdriver to press the retaining tab to release the ice maker assembly and pull it forward. Disconnect the wire harness and remove the entire assembly. Use a large flat head screw driver to pry the cover off, and use a 1/4 inch socket or nut driver to remove the bolt securing the sensor wire bracket at the front and detach the bracket. Disconnect the wire harness and remove the bolts securing the ice maker to the baffle on the bottom. Pull the ice maker out and remove the thermal fuse. Although we do not have an exact video for this part, I have included a link to a video for a similar part to assist you. Hope this helps! https://www.youtube.com/watch?v=hmCE3oKpEk0

Hello Clayton, thank you for your question. No, unfortunately, this kit does not come with the water valve. In order for us to locate the correct parts and repair information we will require the model number of the appliance. If you'd like to have the part number for the valve, or any other part please located the model number and resubmit the question and we will be happy to help you. Look forward to hearing from you!

Hi John, Thank you for your question. The new icemaker does not include a new cover, ice level arm, or wire harness, these components will need to be reused from original icemaker. The on/off switch that is attached to the cover can be used for the new ice maker. If you need a new on/off switch, the part number for it is PS11740324. We hope this helps!

Hello Fred, Thank you for the question. Here is a link to a How To Video that may help. Thank you for your inquiry, good luck with this repair! https://www.youtube.com/watch?v=hmCE3oKpEk0&t=21s

Hi Clara, Thank you for your question. If your icemaker is not dispensing ice, there are some parts that you will need to check to see which one is causing the issue. You will need to check the ice maker motor, the cycling thermostat, the auger and the auger motor. We hope this helps! Good luck with the repair!

Hello Courtnay, Thank you for the question. The Icemaker would not effect the Drawers. We suggest testing the Thermistor. The resistance of the thermistor in the unit should be 2.7K ohms at 77 degrees. We hope this helps!