Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Joni B - November 24, 2022
Verified Purchase
Great.
Arrived quickly, easy install. Affordable.
Thank you
★★★★★
★★★★★
Paul L - February 10, 2022
Verified Purchase
Quick fix
The part was perfect and easily installed.
★★★★★
★★★★★
Daniel W - September 15, 2021
Verified Purchase
Quick fix
Got the part in 2 days,install was a breeze a monkey could have done it...wayyyyyy too expensive
★★★★★
★★★★★
Robert H - March 13, 2021
Verified Purchase
Great part, Great service
Part arrived in good condition, and super fast. Could not believe how fast it was here and got the dryer up and running quickly.
★★★★★
★★★★★
Colin H - December 19, 2020
Verified Purchase
Replacing the control dial
The part we received was the perfect fit for my dryer. It was easy connect and solved the problem instantly.
★★★★★
★★★★★
Robert S - July 13, 2020
Verified Purchase
correct OEM part
Dryer heating like its new
★★★★★
★★★★★
Miles T - February 19, 2019
Verified Purchase
It works
Took 10 minutes to install and fixed our problem. Seemed to be good quality if not a factory replacement.
★★★★★
★★★★★
Andrew S - February 17, 2018
Verified Purchase
Right Solution Not On Diagnastic List
Part worked but it was a problem not on the PartSelect diagnostic list. It should be since I had to get to the solution by replacing 3 other parts first.
< Prev
1
Next >
Customer Repair Stories
Average Repair Rating: 4.7 / 5.0, 3 reviews.
What's this?
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Timer knob popped off. Base rod into knob snapped. Needed new timer
Removed back panel screws. Left/Right, Center. Grabbed Canned Air and sprayed inside panel. Lots of lint ... Unscrew timer - Single center top screw. Tiny threads, kind of wide head. Unplug 4 wire adapters .. (top/left/right/bottom). All 4 pin adapters have unique A/B side. Can't mix up. Reconnect wires, tighten
... Read moretop center screw. Before closing up panel, plug in test with empty tumble to confirm if dryer heats up. (Gas Dryer). All good, has worked great.
Bought the part and removed 10 screws unplugged the wiring and applied it to the new part. Reassembled, done. Super easy, works great!
Joseph from LINCOLN, RI
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
2 of 2 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Unable to use heat selector knob which was always tight to turn and finally broke
First unplug it. Take off 4 screws on back of panel, remove two small screws where dryer screen is pulled out of, place a small screw driver under front part of cover and pop is up, careful not to brake, there will be two big spring type clamps you use player to remove on each side, flip cover on back and unplug all the connectors to the
... Read moredryer timer, remove the few screws holding it, plug back in all the connectors, put back in and screw is back on, put spring clamps back on using pliers, tilt cover back in, snap cover back in, put screws back that you took out, put knob back on and done.
Read less
Dwight from SAN Ysidro, CA
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers, Socket set
1 personfound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
Next >
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
12 questions answered by our experts.
Sort by:
< Prev
1
2
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Ramiro
February 18, 2020
Hello my name is ramiro and i have a problem with the dryer. The timer of the dryer works but it doesn't count down it stays only in one spot and i have to keep checking if the cloths are dry. Do i have to replace the timer?
For model number 3238965929
Hello, Thank you for your question. That typically is the cause when the dryer timer is not fully functioning it will need to be replaced. We hope this helps.
9 people found this helpful.
Was this helpful?
Thank you for voting!
Steve
December 5, 2018
Can a bad timer stop the dryer from heating
Hi Steve,
Thank you for your question. The timer consists of a small motor connected to a series of gears that rotate cams, which turn electric contacts off and on inside the timer. The timer contacts control the dryer motor as well as the heat circuit. A defect in the timer’s electrical contacts can cause the dryer to stop producing heat and the timer will need to be replaced. The contacts can be checked for continuity with a multi-meter. Unplug the dryer before conducting this test. Before you can begin to test your dryer's timer motor, you must first locate the device. It is a part of the timer assembly. Dryer timer assemblies are located behind the control console panel. You may only have to remove the screws securing the front control panel in place, or, depending on your model, your may have to remove the rear panel behind the control panel.
Label the wires connecting to your timer motor so that you will be able to correctly reconnect them later. Carefuly remove the wires. Do not pull on the wire itself. Instead, use needle nose pliers to pull gently on the wire connector.
Set your ohmmeter to the R x 1 setting. Take each probe and touch it to one wire. A normal reading for most dryers is in the 2000 to 3000 ohms range. Try to locate a schematic for your dryer. It should be in one of the service areas of your dryer or in the owner's manual. This schematic should indicate the proper resistance reading for your specific timer motor.
If the reading you receive from testing your timer's motor differs greatly from the range presented here, then you should replace your timer motor, or the entire timer assembly. I hope this helps. Thank you and have a great day!
6 people found this helpful.
Was this helpful?
Thank you for voting!
Marlene
June 21, 2019
Hi, My timer is broken and it has the same part number as your product, but it also has a letter after it. This is for Maytag MGDC215EW2. Do you think they are compatible? Thank you.
For model number MGDC215EW2
Hi Marlene,
Thank you for your question. The part number listed under your model number for the is PS11749830. I hope this helps. Thank you and have a great day!
2 people found this helpful.
Was this helpful?
Thank you for voting!
Chris
November 19, 2019
How do i test to see if the timer control is the problem. I replaced several other parts and only get heat at the end of cycle on less dry. Otherwise the dryer never ignites. I did the thermostat, ignitor, and several other parts already with the same issue still
For model number Wgd4800xq4
Hello Chris and thanks for writing.
We have attached the link to a repair video. We hope this helps. Please contact us anytime.
https://www.youtube.com/watch?v=nAbe2JCmrAA
2 people found this helpful.
Was this helpful?
Thank you for voting!
Delphine
October 26, 2021
The dryer works and dries clothes, but the cycle knob only works in one position when using the automatic drying. It won't turn on unless it is at a certain position near the energy preferred area. And once it times out, I have to go back past the beginning of the cycle. I'm not sure what part is malfunctioning.
For model number WGD4800XQ1
Hello Delphine, Thank you for the question. This would be caused be a defective Dryer Timer Control Switch that is behind the Knob, PartSelect Number PS11749830. If you need help placing an order, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Danny
December 5, 2019
As for my last question you answered the thermal fuse checked good
For model number WGD5200VQ1
Hi Danny, thank you for your question. When you are experiencing an issue like this there are a few parts that you will have to test to determine what is causing your issue. For all of these parts you can test them with a multi meter. First you will have to test your thermostats and thermal fuses to make sure they are all functioning correctly. After that you will want to test parts in this order, your m series coils, igniter itself, or your radiant flame sensor. You may also want to check your regulator just to make sure that part is functioning properly as well. Something else you should also check would be your filter and ducts. Make sure there is absolutely no blockage that would restrict air flow in your appliance. I hope that helps. Good luck with your repair.
1 person found this helpful.
Was this helpful?
Thank you for voting!
Danny
December 5, 2019
Have checked everything in back of dryer all was good also replaced coils also good but dryer will on heat on delicate have also changed temp. Selector where do i need to go now? There is only one item left that's the control unit could that be the problen
For model number WGD5200VQ1
Hello Danny, thank you for writing. This is likely due to a faulty Thermal Fuse, part number PS11741460 for your model dryer. Good luck with your repair!
Was this helpful?
Thank you for voting!
Ben
February 6, 2019
Gas dryer only worked on one cycle. Thought it might be the timer. Took it out, checked and cleaned contacts, put it back and doesn't work at all. No igniter now, fuses test good. However when taking the timer off the motor screws had to be taken out to remove plate, and motor came out of shaft for timer. Put it back on, but now it won't ignite igniter, so no heat. Would timer being out of sync when i put the motor back in possibly be the issue?
For model number wpw10185981
Hello Ben, Thank you for contacting us. Please resubmit your question on the site with the model number of your equipment so that we can find the parts and information for you. Thank you.
Was this helpful?
Thank you for voting!
Edward
June 28, 2022
Knob slides off unit. Appears plastic part that holds knob and pin to timer is broken. What part do I order to repair this
For model number WGD4815EW2
Hello Edward, thank you for writing. Yes, the Dryer PS11749830 you had chosen is compatible with your model. If you need help placing an order, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you.
Was this helpful?
Thank you for voting!
Chris
December 15, 2022
timer knob broke do i have to replace timer assy
For model number wgd4815ew2
Hello Chris, thank you for reaching out. According to our research, you may only need to replace the knob, part number PS16221236. If the shaft behind the knob also broke, then you need to replace the timer control, part number PS11749830. Customer service is available 7 days a week if you need help placing an order. Glad to be of assistance!
