Sensor WPW10178988

Hi John,thank you for the question. F51 would indicate that the control board is not seeing the proper resistance on the motor circuit . You should check that you have proper voltage to the unit. It can also indicate that your rotor position sensor is either not registering or it is just bad. Remove the connector for the rotor position sensor and clean off any corrosion built up on the connector. After that try to run a cycle. If that does not work and you continue to get the same error, replace the rotor position sensor,PartSelect Number: PS11749664. Hope this helps!

Hello Roger, thank you for your question. The UL means there is an Unbalanced load. I would check the suspension rods are in good condition. If all is well there, I would check the sensor part number WPW10178988. It helps to ensure the load of clothing stays balanced during the wash cycle. There is quite a bit of information about this part on our site. I hope this helps!

Hello Caneron, Thank you for the question. The next part we suggest is the PartSelect Number PS11749664. This rotary position sensor is a genuine OEM part for your washing machine. It helps to ensure the load of clothing stays balanced during the wash cycle. Hope this helps, good luck with this repair!

Hello Raul, thank you for contacting us. With the washer draining slowly it sounds like an issue with the drain pump. Also if it is not spinning it could be an issue with the basket hubs, those would need to be replaced if worn out. Hope this helps!

Hi Chris, Thank you for your question. The F51 error code is letting you know that the main control board has detected either a bad rotor position sensor or there is a wiring problem in the lower wiring harness. If you think you have put the sensor in incorrectly, there is a video listed with the sensor on our website that you may reference on how to install the part. If it is not the sensor it is likely a wiring issue in the lower wiring harness. The main control board may cause this issue as well. Here are some steps to try to see if you can figure it out. Reset the washer by unplugging it or turning the breaker off for a few minutes then turn the power back on. This will reset the main control board by allowing all the capacitors in the control to drain. Start a new cycle and if the error returns, follow the information below. Remove the cover panel on the back of the console and make sure that P5 and P10 plug connectors are properly connected to the board. Check the wiring from the board to the lower harness where it plugs in to the rotor position sensor making sure that none of the wires are damaged. If wiring is fine, you will need to test the sensor, the wiring and the main control board with a multimeter to see which part is causing the issue. You will need to test the parts with a multimeter. Here is a link to one of our videos on YouTube that you may use as a general reference on how to use one, https://www.youtube.com/watch?v=bWC44fHn0As. I hope this helps. Thank you and have a great day!

Hello Jeff, Thank you for contacting us. Based on your symptom I do not have nay further trouble shooting beyond what you have already replaced. I suggest contacting the manufacturer directly. Good luck with your repair!

Hello Linda, thank you for your question. The F1 error code indicates a problem with the water level pressure transducer signal on the machine control board. We would recommend checking the water level pressure hose and if that part is not kinked or cracked the main control board would have to be replaced which is PartSelect Number PS11746554. I hope this helps.

Hello Jeff, thank you for your question. We would recommend checking the hubs (PartSelect Number: PS11723155), the drum bearing to see if you can notice any wear and tear, as well as the PartSelect Number PS11749664 Sensor.. It helps to ensure the load of clothing stays balanced during the wash cycle. I hope this helps!

Hi Ronnie, Thank you for your question. The SD or SUD error code on your appliance means that you have excessive suds built up. This happens when you are using too much detergent or using a non high efficiency detergent in a high efficiency washer. What your appliance is doing during this is putting more water into your washer so that it can break up all of the suds. This can make your cycle a lot longer than usual. If you change to a HE detergent and have started to use less and you still get the error, it is suggested that you run your appliance through a Clean Washer cycle so that it can clean up any detergent build up inside of the machine. I hope that helps. Good luck with your repair.

Hi John, Thank you for the question. The UL means there is an Unbalanced load. I suggest removing the front panel and checking the Suspension Rods,PartSelect Number PS2355518. Hope this helps!