Dryer Nut WPW10139757 | Official Whirlpool Part | Fast Shipping | PartSelect
Dryer Nut – Part Number: WPW10139757
( Grid squares measure 1x1 inch )
Dryer Nut – Part Number: WPW10139757 Dryer Nut – Part Number: WPW10139757 https://partselectcom.azureedge.net/Schematics/Maytag/17847.gif

Dryer Nut

PartSelect Number PS11748944

Manufacturer Part Number WPW10139757

Manufactured by Whirlpool

Product Description

Dryer Nut Specifications

Sold individually. This nut is for dryers. Follow appropriate safety practices when installing the nut.

How Buying OEM Parts Can Save You Time and Money

Troubleshooting

This part works with the following products:

Dryer, Washer, Washer Dryer Combo, Grill, Microwave, Furnace.

This part works with the following brands:

Amana, Speed Queen, Maytag, Crosley, KitchenAid, Admiral, Magic Chef, Kenmore.

Part # WPW10139757 replaces these:

20275, 20281, 24001419, 24001510, 27001225, 52566, 8190116, AP6015663, M0282405, M1D974, R0601011, R0601025, W10139757.
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Customer Repair Stories
Average Repair Rating: 2.6 / 5.0, 3 reviews What's this?
Sort by:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Jim from Frisco, TX
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Wrench set
Parts Used:
WPY54414, WP37001144, WPW10139757, WP233520, 500824, WP23748
High pitched squealing noise for about 5 minutes when I first turned the dryer on. As the problem worsened, the squealing became more prevalent and annoying.
Removed the two sheet metall screws on the front foot panel, removed the four screws holding the door assembly, wrote down the wiring placement for the front door, removed the blower bulkhead assembly by removing one screw in the bottom of the dryer. Removed two screws and propped the dryer top panel up at a 45 degree angle to gain additional clearance. Removed the drum and belt from the front and back seals by applying simple outward pressure. Removed the screw in the bottom of the motor assembly allowing me to reposition the assembly for easy access. Removed bolt holding old Idler arm assembly. Assembled new Idler pulley referring to old assembly. Reversed the process to complete the repair. Note: I found it easier to simply hang the dryer belt over the dryer drum when replacing the drum in the dryer. First you need to place and align the drum then route the belt back to the moter pulley and then over the idler pulley. if you try to put the belt over the motor and then align the drum, it is difficult to keep the belt on the pulley. It might help to draw a diagram of the belt route or obtain the belt route diagram from the website for reference. Very easy job.
13 of 17 people found this instruction helpful.
Was this instruction helpful to you?
George from Haverhill, MA
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Wrench set
Parts Used:
500824, WP40111201, WP37001287, WPW10139757
broken belt and idler pully
Remove front pannel
remove wires to light and switch
remove drum panel
disconnect motor wiring
unscrew motor mount
replace idlerlever replace belt reassemble all parts
11 of 14 people found this instruction helpful.
Was this instruction helpful to you?
Randal from Centralia, WA
Difficulty Level:
A Bit Difficult
Total Repair Time:
More than 2 hours
Tools:
Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
Parts Used:
500824, WP37001287, WP2200376, WPW10139757, 503613
Noisy, squealing belt tightener
Changed, got in aimed wrong direction-best to take a digital photo before you disassemble. Overtightened bolt and nut in assembly, it seized. Attempted to drill/grind it off, should have removed motor. Drill skipped up into motor windings. Could have replaced dryer, decided not, fixed by ordering motor, mount, nut and bolt and new belt idler. Reassembly was a snap till the gremlins hit again and I lost one of the drum glides. After a trip across town, I reassembled and it was good to go. Disassembly, use a screw driver to pry up the top, use the nut driver to remove upper front left and right screws, lift front forward and off bottom hooks. You have to release the wiring harness, it has four connectors. Use a sharpy marker and write the wire colors next to the plug-ins connectors you pull gently off and set the door aside. The second wires are two wires for the inner assembly which again need to be marked for color and then pulled loose. Pull them through the plastic hold down so they're out of the way. Use nut driver to remove four screws from inner drum holder, pry gently off dryer blower. Reaching around both sides of the blower housing find the belt tensioner, pull it to the right, push the belt out of it. Lift the drum out, up slightly over the back rollers. Set aside. Use the nut driver to remove the screws into the base holding the motor mount down, now lift the motor/blower assembly forward and pull gently loose from the dryer vent pipe. Set it up where you can work on it. Using the nut driver, take the screws off the blower housing, use a vise grip to secure the motor and use a 7/8 inch turning counter clockwise to remove the turbine. Use the nut driver to remove the screws holding the turbine housing in place, pop the motor clips off. Pull the motor off and remove the nut and bolt of the belt idler assembly using a wrench on the back and a socket wrench on the other side. Reverse order to reassemble, when tightening the idler arm tighten it to where you feel it stop but not any further. Put the belt around the drum again, get it in the previous location on the drum, feel around the drum to make sure belt isn't twisted, bring belt in from the back between the idler wheel and the vent pipe in a loop (Make sure the belt is behind the tension spring rather than in front), Tip the idler arm upward, use the other hand to slide the belt loop up over the motor pulley. One final note is this being a Maytag you might write these direction on the inside of the front panel for next time.
6 of 12 people found this instruction helpful.
Was this instruction helpful to you?
Model Cross Reference

This part works with the following models:

PartSelect Number: PS11748944
Manufacturer Part Number: WPW10139757
Brand
Model Number
Description
Amana
6492-LWM-251
Washer - WASHER
Amana
6493-LWM-353
Washer - WASHER
Amana
6494-LWM-423
Washer - WASHER
Amana
6495-LWM-433
Washer - WASHER
Amana
6496-LWM-833
Washer - WASHER
Amana
6497-LW-9203
Washer - WASHER
Kenmore
65189918100
Washer
Amana
7493-LEM437
Dryer - DRYER
Kenmore
99937CE
Dryer - Kenmore Dryer Model 99937CE Parts
Kenmore
99937CG
Dryer - Kenmore Dryer Model 99937CG Parts
Kenmore
99937EG
Dryer - Kenmore Dryer Model 99937EG Parts
Kenmore
99965CG
Dryer - Kenmore Dryer Model 99965CG Parts
Amana
AA3110
Washer - Top Loading
Amana
AA3111
Washer - Top Loading
Amana
AA3210
Washer - Top Loading
Amana
AA3410
Washer - Top Loading
Amana
AA4110
Washer - Top Loading
Amana
AA4111
Washer - Top Loading
Amana
AA4210
Washer - Top Loading
Amana
AA4211
Washer - Top Loading
Amana
AA4410
Washer - Top Loading
Amana
AA4411
Washer - Top Loading
Amana
AA5121
Washer - Top Loading
Amana
AA5220
Washer - Top Loading
Amana
AA5221
Washer - Top Loading
Amana
AA5222
Washer - Top Loading
Amana
AA5420
Washer - Top Loading
Amana
AA5421
Washer - Top Loading
Amana
AA6121
Washer - Top Loading
Amana
AA6221
Washer - Top Loading