Sign In | Create Account
| Your Account
Back
Back
Keep typing for more specific results...

Top Appliance Brands

See All >
Whirlpool Parts Whirlpool General Electric Parts General Electric Samsung Parts Samsung Frigidaire Parts Frigidaire

Top Lawn Equipment Brands

See All >
Toro Parts Toro Briggs and Stratton Parts Briggs & Stratton Husqvarna Parts Husqvarna Craftsman Parts Craftsman

Top Appliances

See All >
Dishwasher Parts Dishwasher Dryer Parts Dryer Stove Parts Stove Refrigerator Parts Refrigerator Washer Parts Washer

Top Lawn Equipment

See All >
Lawn Mower Parts Lawn Mower Chainsaw Parts Chainsaw String Trimmer Parts String Trimmer Hedge Trimmer Parts Hedge Trimmer Generator Parts Generator
Keep typing for more specific results...
Same-day Shipping All Original Manufacturer Parts Genuine Quality 1 Year Warranty
Easy
11748620-1-M-Whirlpool-WPW10121334-Thrust
Part Location Diagram of WPW10121334 Whirlpool Thrust
See part 18 in the diagram
( Grid squares measure 1x1 inch )
11748620-1-S-Whirlpool-WPW10121334-Thrust 11748620-2-S-Whirlpool-WPW10121334-Thrust Part Location Diagram of WPW10121334 Whirlpool Thrust
Customer Service Representative

Get in touch, we're here to help!

1-866-319-8402 Monday to Saturday
8am - 9pm EST

customerservice@partselect.com

Thrust WPW10121334

★★★★★
★★★★★
5 Reviews

Rated by 8 customers 

Easy 

1- 2 hours 

Ratings submitted by customers like you who bought this part.

Easy 

1- 2 hours 

Rated by verified customers 

?
$ 7.95
  In Stock

Get this part fast! Average delivery time for in-stock parts via standard shipping: 1.8 days.

Does this part fit my model?

Need help finding your model number?
PartSelect Number PS11748620
Manufacturer Part Number WPW10121334
Manufactured by Whirlpool for Amana, Kenmore, Speed Queen, Whirlpool

Jump to:

You May Also Need ?
Idler Pulley w/Bracket
$27.23
  In Stock
Multi Rib Belt
$24.10
  In Stock
Dryer Idler Pulley
$25.95
  In Stock
Dryer Tri Ring
$10.95
  In Stock
Dryer Spring
$22.00
  In Stock
Washer Affresh Cleaner
$19.95
  In Stock
Affresh Dishwasher Cleaner Tablets - 6
$21.95
  In Stock
Affresh Washing Machine Cleaner Tablets – 6 Count
$27.95
  In Stock
Refrigerator Produce Preserver
$17.79
  In Stock
Range Cleaner
$14.95
  In Stock
Refrigerator Deodorizer
$25.95
  In Stock
Back to Top
Troubleshooting
This part fixes the following symptoms:
Noisy
This part works with the following products:
Dryer, Washer, Washer Dryer Combo.
Part# WPW10121334 replaces these:
16318, 16707, 233520, 501733, 51068, 52549, R0600526, W10121334, WP233520, WP52549
Back to Top
Customer Reviews
Average Rating:
★★★★★
★★★★★
5 Reviews
4.6
Filter By Rating:
  • 5 Stars
    4
  • 4 Stars
    0
  • 3 Stars
    1
  • 2 Stars
    0
  • 1 Star
    0
Sort by:
  • 1
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Alan L - March 13, 2018
  Verified Purchase
Worked as expected ...
The part fit and worked fine. Added some oil .... and we were off to the races again!
★★★★★
★★★★★
Barbara T - March 5, 2020
  Verified Purchase
works great but the washer wasn't what we should have ordered.
My husband ordered the washer when we needed the main part. We didn't use this part yet keeping it in case we need it in later date.
★★★★★
★★★★★
JEFF L - November 25, 2018
  Verified Purchase
Basic part
Easy to put on
★★★★★
★★★★★
Phil B - May 2, 2019
  Verified Purchase
Washer part
Prompt delivery, easy installation and my washer is working great. Thanks
★★★★★
★★★★★
Robert M - March 20, 2018
  Verified Purchase
Not like the picture
The tension wheel did not look like the original but it did fit. Unlike the picture the tension wheel came with the bottom washer and upper locking washer. I did not need to order those extra parts.
  • 1
Back to Top
Customer Repair Stories
 Average Repair Rating: 2.7 / 5.0, 8 reviews. What's this?
Sort by:
  • 1
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Drum support rollers were shot, idler was changed as well, new belt installed, 2 new thrust washers and felt pads were installed as well.
Repair parts were exact OEM, went very smooth.
Longest part was cleaning the inside of dryer and cutting new vent pipe exit.
Other Parts Used:
Single Drum Glide Felt Pad Multi Rib Belt Dryer Idler Assembly Drum Support Roller Thrust
  • Steven from MORRIS, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Pliers, Wrench (Adjustable), Wrench set
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Loud sreeching and vibration
I just followed the videos I received with the order and everything went really well. This dryer was a little different than the video, but the process was the same. The HE3 does require 4 drum rollers and I had only ordered 2. However, there was only one bad roller, so I installed both on the back of the drum. The two front rollers are pretty easy to get to if they go bad. The idler pulley was completely worn out with an 1/8 inch groove worn off to one side. PartSelect made this an easy project!
Read less
Other Parts Used:
Dryer Tri Ring Dryer Drum Support Roller Thrust Multi Rib Belt Dryer Idler Pulley
  • Robert from TUTTLE, OK
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Pliers, Screw drivers
14 of 15 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The dryer had been squeaking for at least 6 months when it finally became painfully loud and unacceptable
. I had replaced the idler pulley a number of years ago so I assumed that the noise was now due to either the sliders at the front of the drum or bad rollers at the back.. I removed power by turning off the breaker that serviced the dryer. After removing the lower front panel via the two sheet metal screws at the bottom I then removed the door panel. The safety switch behind the door had to be removed by depressing the sides of the switch after disconnecting the two push on connectors. One will discover that reconnecting the smaller of the two contacts to the unused contact on the switch will allow one to run the dryer with the door off or open. This can be useful to test operation after the repair is complete before reassembling the door and lower panels. I then removed the large panel that secures the front of the drum. The drum is then removed after releasing tension on the drive belt. All rotating parts and sliders could then be checked. Upon disassembly I found that the rollers and sliders appeared ok and decided to replace the idler pulley as a last attempt to fix the problem. This is best done by removing the tension arm and tensioning spring. the pulley is then more easily removed from the arm using snap ring pliers. After replacing the pulley and thrust washer with new parts I reassembled everything. I found it helpful to pretension the arm using a zip tie wrap in that the belt can be more easily reinstalled on the drum and pulley. When the drum and belt is properly in place and belt threaded, one can reach in with a pair of cutters and snip the tie wrap to re tension the system. The dryer has been running normally again for a week after affecting this repair.
Read less
Other Parts Used:
Idler Pulley Wheel w/ Bearing Thrust
  • George from WORTON, MD
  • Difficulty Level:
    Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Socket set
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
the drum was clunking and scraping,also it had begun to eat clothing
I disconnected power and vent hose then tipped dryer on its back. I took off lower panel and door ,disconnecting wires to door and light and hanging them over the side,i then removed the front plate and felt seal the plastic fan shroud and lint trap come out as one piece along with the front plate.when i could look down on the drum,standing on the left side ,i disconnected the screw connecting the top plate to the left side plate allowing the top to gain a little play,this is the amount needed for the drum to be removed,pull belt tensioner slightly as to release tension remove the belt from motor shaft.At this point remove drum and set aside,the lower felt ring and support rollers will be exposed as well as tension spring and tension roller,i used a mirror and guided the snap ring pliers into place on the tension roller,At this point pull on rear felt ring it may come loose easy ,if not work some adhesive remover into the cracks where the glue is and keep agitating it ,eventually the glue will begin to release and more and more of the remover can get in washing the felt ring off,clean real good after using remover soap and water and allow to dry ,apply a thin ring of high heat adhesive smooth out to spread even all around when it becomes tacky begin applying new felt ring,while this adhesive cures perform the same procedure on the front panel and its felt ring while these rings are drying into place undo snap rings and pull support rollers out and replace in like order replacing thrust washers and snap rings if you damage them ,the roller on the tensioner is more tricky but if you use a mirror and a light it is easy to sneak in there lastly when preparing to reassemble and drum and belt are in place just before you replace the front panel it is prudent to replace the neoprene slides,reassemble front plate and ensure that the felt ring lines up and goes in evenly all the way around re-attach top left corner ,reinstall door and wires as well as bottom plate this will conclude the procedure i learned all of this the hard way i should have just replaced all the parts at once i was in that machine 6 different times Daniel 2017
Read less
Other Parts Used:
Cylinder Felt Seal Drum Support Roller Thrust
  • Daniel from ridgecrest, CA
  • Difficulty Level:
    Difficult
  • Total Repair Time:
    More than 2 hours
  • Tools:
    Nutdriver, Pliers, Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
High pitched squealing noise for about 5 minutes when I first turned the dryer on. As the problem worsened, the squealing became more prevalent and annoying.
Removed the two sheet metall screws on the front foot panel, removed the four screws holding the door assembly, wrote down the wiring placement for the front door, removed the blower bulkhead assembly by removing one screw in the bottom of the dryer. Removed two screws and propped the dryer top panel up at a 45 degree angle to gain additional clearance. Removed the drum and belt from the front and back seals by applying simple outward pressure. Removed the screw in the bottom of the motor assembly allowing me to reposition the assembly for easy access. Removed bolt holding old Idler arm assembly. Assembled new Idler pulley referring to old assembly. Reversed the process to complete the repair. Note: I found it easier to simply hang the dryer belt over the dryer drum when replacing the drum in the dryer. First you need to place and align the drum then route the belt back to the moter pulley and then over the idler pulley. if you try to put the belt over the motor and then align the drum, it is difficult to keep the belt on the pulley. It might help to draw a diagram of the belt route or obtain the belt route diagram from the website for reference. Very easy job.
Read less
Other Parts Used:
Idler Pulley Wheel w/ Bearing Idler Pulley Lever and Shaft Dryer Nut Thrust COMPLETE R Retaining Ring
  • Jim from Frisco, TX
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Wrench set
14 of 20 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
worn out bushing in support roller, dryer glides and felt disinigrated. worn out felt cylinder seal
Unscrew front, detach electrical, tilt back top, remove drum. remove retaining ring and glide, replace ring and guide remove old felt seal, adhere new felt seal with contact cement, remove what was left of felt pads, replace pads and new glides, reassemble.
Other Parts Used:
Drum Glide Cylinder Felt Seal Drum Support Roller Thrust Single Felt Pad Multi Rib Belt Retaining Ring
  • Mike from San Clemente, CA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
2 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dryer would squeal when drying clothes
Unplugged dryer, turned off gas, raised front of dryer with two 2X4's on edge resting on legs, removed two lower panel screws, removed lower panel. Removed lower blower & filter assembly, screws (3) are on the inside of drum. (Good chance to clean it out) Removed two lower front upper main panel screws. Supported top panel with wood for access. Removed panel slowly, marked wires that go to door switch, set panel aside. Removed tension on belt by reaching in on the right lower side and unhooking the tensioner from belt, look to see how it is installed, for reinstallation on assembly. Pulled drum out slowly as not to damage seals on drum. replaced parts, attached with self tapping screws.(screws all the same size) reassembly in reverse order. Will need to put belt on drum before installing drum. Check drum alignment with rollers and seals. Used very small amount of high pressure grease on roller bracket and shaft assembly where the support roller shaft spins for lubrication. All's quiet. (Vacuumed out inside while dissassembled)
Read less
Other Parts Used:
Drum Support Roller Thrust Drum Support Roller and Shaft Assembly Multi Rib Belt Retaining Ring
  • JOHN from CORPUS CHRISTI, TX
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
36 of 42 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Washe would not spin clothes or agitate well
Pulled motor, as the belt will not come off unless you take to water pump off off the motor. Installed new idler wheel, washers, clips and belt. Reinstalled motor.
Works good and hopefully lasts a long time!
Other Parts Used:
Spin Belt Thrust Idler Pulley Wheel Retaining Ring
  • Berry from Mt Sidney, VA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Screw drivers, Socket set
8 of 11 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • 1
Back to Top
Questions and Answers

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

Back to Top
Model Cross Reference
This part works with the following models:
PartSelect Number: PS11748620
Manufacturer Part Number: WPW10121334
Brand
Model Number
Description
Kenmore
10687884100
Dryer
Kenmore
10687884300
Dryer
Kenmore
10687884600
Dryer
Kenmore
10697502820
Dryer - Kenmore Dryer Model 106.97502820 (10697502820, 106 97502820) Parts
Kenmore
11051730
Washer
Kenmore
11055594
Washer
Kenmore
1105807410
Dryer
Kenmore
1105808010
Dryer
Kenmore
1105808700
Dryer
Kenmore
1105808800
Dryer
Kenmore
1105808810
Dryer
Kenmore
1105808850
Dryer
Kenmore
1105808860
Dryer
Kenmore
1105817820
Dryer
Kenmore
1105817830
Dryer
Kenmore
1105818810
Dryer
Kenmore
1105818820
Dryer
Kenmore
1105907000
Dryer
Kenmore
1105907100
Dryer
Kenmore
1105907400
Dryer
Kenmore
1105907500
Dryer
Kenmore
1105907501
Dryer
Kenmore
1105907600
Dryer
Kenmore
1105907610
Dryer
Kenmore
1105907700
Dryer
Kenmore
1105907710
Dryer
Kenmore
1105907720
Dryer
Kenmore
1105907721
Dryer
Kenmore
1105907730
Dryer
Kenmore
1105907800
Dryer
Back to Top
Customer Service Representative

Get in touch, we're here to help!

1-866-319-8402 Monday to Saturday
8am - 9pm EST

Contact Customer Service
Thrust
$ 7.95
  In Stock
✖
Stock Status
 In Stock

Item is in stock and will ship today if your order is placed before 4:00 PM Eastern Standard Time.

If your order is placed after 4:00 PM EST, the in stock items will ship on the next business day.

 On Order

Item is not in stock and usually ships 3-5 business days from the time you place your order.

 Special Order

Item is not in stock and usually ships 10-15 business days from the time you place your order.

 NLA - No Longer Available

This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.