Maytag/Maytag_Thumb/TCQNS8DN.gif
See part 1 in the diagram
( Grid squares measure 1x1 inch )

Get in touch, we're here to help!

Open until 10PM EST

customerservice@partselect.com

Front Load Washer Bellow - Gray

★★★★★
★★★★★
16 Reviews
$ 153.77   In Stock

Get this part fast. Average delivery time via standard shipping: 1.8 days.

PartSelect Number PS11748353
Manufacturer Part Number WPW10111435
Manufactured by Whirlpool
Product Description

Front Load Washer Bellow - Gray Specifications

Also known as a door boot seal.This part is used to keep the clothes inside the tub during the wash cycle. The folds in the bellow allow the tub to move separately from the door during the spin cycle.

How Buying OEM Parts Can Save You Time and Money

Troubleshooting
This part fixes the following symptoms:
Leaking | Marks left on clothes
This part works with the following products:
Washer.
This part works with the following products:
Kenmore, Whirlpool, Maytag.
Part# WPW10111435 replaces these:
AP6015081, 8540350, 8540952, W10111435, W10178959, W10181962, W10189283, W10253210, WPW10111435VP
Questions and Answers

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

8 questions answered by our experts.
    Sort by:
    Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
    Cassie
    April 2, 2018
    Hello, my washer is leaking from what appears the front and water is dripping down into the drawer below. We only notice this with heavier loads like towels. Is it likely the bellow is the concern given that it doesn't leak with lighter loads? Thanks for your advice!
    For model number WFW8300SW04
    Hello Cassie, thank you for your question. If there is any leak from the front of the door the bellow is the culprit. It may only happen on larger or heavier loads now, but will probably progress to leaking all the time. I would suggest replacing the Bellow - Gray WPW10111435. Good luck with your repair!

    17 people found this helpful.

    Was this helpful?
    Thank you for voting!
    Bill
    December 3, 2017
    Our machine is dripping water on the inside. When you remove the bottom panel there is a cement counterweight and the water is dripping down the back of the counter weight into the base of the machine. Is this the part that will solve that leak?
    For model number WFW8300SW00
    Hi Bill, Thank you for your question. You would likely have to try and figure out where your leak is coming from. It could be coming from your bellow but it could also be coming from the tun gasket. I would suggest letting your appliance dry out a bit. Maybe open it up so that you can see the inside. Take a little bit of water, pour it over your bellow and see if there is a leak. If there is not, pour some of the water into your tub and spin it around for a minute or so. See if there is a leak. I hope that helps. Good luck with your repair.

    6 people found this helpful.

    Was this helpful?
    Thank you for voting!
    Related Parts:
    Kimme
    November 15, 2017
    My washer boot is black with mold. I saw the replacement part number: Wpw10111435; but i didn't see the number that is listed on my washer (8540903). The closest was 8540954. The serial number of mine is: Hlt1677748 (about 11 years old. I bought the floor model when i moved here.) please let me know if this indeed is the appropriate boot for my old washer. Many thanks. Kimme
    For model number WFW8300SW00
    Hi Kimme, Thank you for contacting us. Based on the model number you provided, the bellow you have referenced in your question is the correct part for your appliance. I hope this helps. Thank you and have a great day!

    2 people found this helpful.

    Was this helpful?
    Thank you for voting!
    Alexander Pries
    January 12, 2018
    Hi there, we have a Kenmore front loading washer that leaks a small amount of water into the metal frame at the bottom. I removed the kickplate and noticed that the water is dripping from the backside of the bottom concrete counterweight. I also noticed that the water only seems to drip during the high spin portion of the washing cycle. During normal agitation, there seems to be no leakage or maybe just holdover drips from the high spin phase. Is replacement of the door bellow the most likely solution or could there be another faulty part? I ask because i had previously replaced the door bellow about six months ago and have noticed no leaks until recently. Thank you!
    For model number Kenmore 110.47511702
    Hello Alexander, Thank you for your inquiry. You can pull the bellow out and check for any rips or tears. Check the drain hoses and tub to pump hose as well. The other parts that could cause this issue are the drain pump, the water inlet valve and the tub assembly. Hope this helps!

    1 person found this helpful.

    Was this helpful?
    Thank you for voting!
    Kally
    January 31, 2019
    Hi i was wondering which gasket seal for the door replaces my model washing machine. Thank you
    For model number MHWZ400TQ01
    Hello Kally, thank you for your question! PartSelect Number PS11748353 is the correct part for your model. Good luck with your repair!

    1 person found this helpful.

    Was this helpful?
    Thank you for voting!
    Alix
    August 26, 2019
    Hi, I have the Whirlpool WFW8300SW00, is this bellow compatible with my washing machine? Thanks.
    For model number WFW8300SW00
    Hi Alix, Thank you for your question. Yes, this would be the correct bellow for your washer. I hope this helps. Thank you and have a great day!

    1 person found this helpful.

    Was this helpful?
    Thank you for voting!
    Miriam
    December 12, 2019
    My washer is leaking from the bottom of the door and I'm assuming this is the part I would need to fix it? Will it fit my model. Serial # hlu429267.
    For model number 11047532602
    Hello Miriam, thank you for the question. With leaking at the door, in most cases the Front Load Washer Bellow - Gray, PartSelect Number PS11748353 will need to be replaced. Hope this helps!

    1 person found this helpful.

    Was this helpful?
    Thank you for voting!
    Chelsea
    December 28, 2017
    My washer leaks when on normal on any mode. It leaks in the front corners.And into the drawer. I have to put rags on the front corner to soak up water. I'm thinking that it is the seal of the washer? Could that be it.
    For model number WFW8400TW02
    Hi Chelsea, Thank you for the question. I suggest replacing or checking for damage on the Bellow, PartSelect Number PS11748353. It may have just come lose. At times it can get pinched or split and will need to be replaced. Hope this helps!

    Was this helpful?
    Thank you for voting!
      Part Videos

      Replacing your Kenmore Washer Front Load Washer Bellow - Gray

      Customer Repair Stories
       Average Repair Rating: 2.8 / 5.0, 12 reviews. What's this?
      Sort by:
      Sorry, we couldn't find any existing installation instruction that matched.
      Water leak from bottom of door.
      I discovered water leaking from the bottom of the door on our Kenmore front load washer. I did a little self diagnosis from the internet and found that this seems to be a common problem for front load Kenmore washers and that the ususal suspect is the large rubbery bellows. I examined the bellows on my washer and although I didn't find anything wrong with it, I couldn't find any other likely causes. I shopped around and found PartSelect to be the cheapest for the replacement part. Removal is easy by removing the lower front panel with three small screws on the bottom front, then remove the very top panel and then the top front control panel and finally the door panel. the bellows are actually held in place with a spring loop on the outer and a screw tightener on the inner, both are fairly easy to remove and the bellows comes right off. For installation my best advice is to lube the bellows with a small amount of dishwashing soap in the groove that fits on the washer tub. This will help it slide into place and enables a small amount of sliding fine tuning once it is on. From there it is just a reverse of the removal.
      • Marty from Belfair, WA
      • Difficulty Level:
        Easy
      • Total Repair Time:
        30 - 60 mins
      • Tools:
        Nutdriver, Pliers, Screw drivers
      • Parts Used:
        WPW10111435
      190 of 211 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      My Epic Z is only three years old but started to leak at the bottom of the washer door for no obvious reason. Before replacing the bellow, I suggest you make sure the door latch is not loose and also make sure the star driver screws that secure the glass in the door are all snug (do not overtighten)
      Since most people do not replace bellows for a living, I have great instructions for you to follow. I found the entire repair manual on the web.Just follow the repair instructions as written. Two other suggestions, use a very small amount of liquid diswasher soap to lubricate the bellow when fitting it over the washer drum assembly, makes life a lot easier. Second, get a second pair of hands to help you hold the bellow in place as you mount it or you will find yourself "chasing your tail". Bellow replacement and tightening the door and latch fixed the problem. Mom was happy :)...PS the buying experience from PartSelect , part delivery, speed was perfect!
      • Robert from Charlotte, NC
      • Difficulty Level:
        A Bit Difficult
      • Total Repair Time:
        30 - 60 mins
      • Tools:
        Nutdriver, Screw drivers
      • Parts Used:
        WPW10111435
      51 of 54 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      Bellow was cut on the bottom, leaked.
      The top panel was removed, right side pulls out, left side has a lint drawer that pulls out exposing a phillips head screw. The bottom panel is removed by taking three screws out of the bottom, then the panel pulls down. Remove the additional screws (4) holding the door panel on. Loosen the band (phillipshead screw) holding the bellow on and pull the bellow off the channel. It also pulls off the door opening channel. Pull the new piece over the channels, tighten the band and reverse the removal procedure.
      • Richard from Mount Pocono, PA
      • Difficulty Level:
        Easy
      • Total Repair Time:
        15 - 30 mins
      • Tools:
        Nutdriver, Screw drivers
      • Parts Used:
        WPW10111435
      32 of 46 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      leaking at door
      once i figure out how to take off front panel it went quite smoothly also my wife gave me a hand putting the bellows on,her fingers were smaller so it was alittle easier for her
      • william from wauseon, OH
      • Difficulty Level:
        A Bit Difficult
      • Total Repair Time:
        30 - 60 mins
      • Tools:
        Nutdriver, Pliers, Screw drivers
      • Parts Used:
        WPW10111435, WP8540108
      22 of 46 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      water leak
      Remove outer retaining ring by pulling spring clip located at bottom of the seal. Push the bellows into the tub. Loosen the inner retaining ring clip (located on the left, facing the front of the machine) with a phillips screwdriver and guide the ring out. Remove the old bellows. Put in the new part with the tab on top and the drain holes on the bottom. Reinstall the rings. Kind of tedious but not complicated.
      • Christopher from Myrtle Beach, SC
      • Difficulty Level:
        Easy
      • Total Repair Time:
        15 - 30 mins
      • Tools:
        Pliers, Screw drivers
      • Parts Used:
        WPW10111435
      19 of 24 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      replaced leaking bellows
      I followed the description on this site, my machine was slightly different, but the basic procedure was the same. The tip to apply a small amount of the liquid soap to the bellows was useful to ease installation. Make sure the holes in the bottom of the bellows align with the drain in the bottom of the washer. The portion of the bellows that attaches to the main body via the adjustable clamp can be done by a single person with two hands. The portion that attaches to the front panel with the spring-wire band is a four hand job. Position the bellows, attach / position the wire-band with the spring portion on the bottom. Starting at the top get your helper to hold it in position, using needle nose pliers stretch the last bit of the wire-band into final position.
      • thomas from santa cruz, CA
      • Difficulty Level:
        A Bit Difficult
      • Total Repair Time:
        1- 2 hours
      • Tools:
        Nutdriver, Pliers, Screw drivers
      • Parts Used:
        WPW10111435
      16 of 18 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      Bellow was torn at the door causing water to leak
      I would recommend to remove the front loader door first. Then remove the clamp that holds the front of the bellow to the washer, Remove the top panel and then the front panel. Remove the band that holds the back of the bellow to the washer. Reverse the process to install the bellow. It helps to apply a little soapy water to make it easy to put the bellow on the track for both the front and back. It also helps to have four hands. Hope you have a friend or significant other.
      • Rich from Los Altos, CA
      • Difficulty Level:
        Easy
      • Total Repair Time:
        15 - 30 mins
      • Tools:
        Screw drivers, Socket set
      • Parts Used:
        WPW10111435
      11 of 13 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      Door seal had gone bad leaked
      Looked how the old one came off and revearsed the process. Ordered the part, it was shipped right away and recieved it in three working days. Normal shipping too. Very pleased with the handling of my order.
      • Roy from Summerville, SC
      • Difficulty Level:
        A Bit Difficult
      • Total Repair Time:
        30 - 60 mins
      • Tools:
        Screw drivers
      • Parts Used:
        WPW10111435
      10 of 17 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      Water leaked from front bellows. (Door gasket)
      Easier if you block up front feet on 2x4 blocks. remove bottom front panel. Remove detergent dispenser tray. Remove top front panel. On door remove large round retainer clamp to bellows. (Pop off with screwdriver.) Remove door. Remove inner bellows clamp. Use phillips screwdriver to loosen it. If the input water filler hose is in the way, pull it out, but don't forget to put it back on or a flood will ensue!! Replace by doing everything in reverse order.
      • Joseph from EAST SYRACUSE, NY
      • Difficulty Level:
        Easy
      • Total Repair Time:
        30 - 60 mins
      • Tools:
        Nutdriver, Screw drivers
      • Parts Used:
        WPW10111435
      2 of 3 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      Leaking
      Followed the video except to use clamps to hold the Bellow To Front Panel Clamp in place while I worked the clamp around the from of the Bellow. I used a plastic pry tool in place of the suggested screw driver to pry the control panel off.
      • Linda from S SAN FRAN, CA
      • Difficulty Level:
        Easy
      • Total Repair Time:
        1- 2 hours
      • Tools:
        Nutdriver, Screw drivers
      1 person found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      Customer Reviews
      Average Rating:
      ★★★★★
      ★★★★★
      16 Reviews
      4.1
      Filter By Rating:
      • 5 Stars
        9
      • 4 Stars
        4
      • 3 Stars
        1
      • 2 Stars
        0
      • 1 Star
        2
      Sort by:
      Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
      Model Cross Reference
      This part works with the following models:
      PartSelect Number: PS11748353
      Manufacturer Part Number: WPW10111435
      Brand
      Model Number
      Description
      Kenmore
      11046462500
      Washer
      Kenmore
      11046462501
      Washer
      Kenmore
      11046472500
      Washer
      Kenmore
      11046472501
      Washer
      Kenmore
      11047511700
      Washer
      Kenmore
      11047511701
      Washer
      Kenmore
      11047511702
      Washer
      Kenmore
      11047512600
      Washer
      Kenmore
      11047512601
      Washer
      Kenmore
      11047512602
      Washer
      Kenmore
      11047512603
      Washer
      Kenmore
      11047512604
      Washer
      Kenmore
      11047512605
      Washer
      Kenmore
      11047531700
      Washer
      Kenmore
      11047531701
      Washer
      Kenmore
      11047531702
      Washer
      Kenmore
      11047532600
      Washer
      Kenmore
      11047532601
      Washer
      Kenmore
      11047532602
      Washer
      Kenmore
      11047532603
      Washer
      Kenmore
      11047532604
      Washer
      Kenmore
      11047532605
      Washer
      Kenmore
      11047542600
      Washer
      Kenmore
      11047542601
      Washer
      Kenmore
      11047542602
      Washer
      Kenmore
      11047542603
      Washer
      Kenmore
      11047542604
      Washer
      Kenmore
      11047542605
      Washer
      Kenmore
      11047561600
      Washer
      Kenmore
      11047561601
      Washer

      Get in touch, we're here to help!

      Open until 10PM EST

      Contact Customer Service