Drive Belt WPW10006384 | Official Whirlpool Part | Fast Shipping | PartSelect
Drive Belt – Part Number: WPW10006384
Drive Belt – Part Number: WPW10006384 Drive Belt – Part Number: WPW10006384 https://partselectcom.azureedge.net/Schematics/Whirlpool/NG68TURJ.gif

Drive Belt

Product Description

Drive Belt Specifications

The main drive belt is designed to ride on the pulley until the basket gets up to speed.

How Buying OEM Parts Can Save You Time and Money

Troubleshooting

This part fixes the following symptoms:

Noisy | Pumps but will not spin | Will not agitate | Burning smell

This part works with the following products:

Washer.

This part works with the following brands:

Whirlpool, Maytag, Kenmore, Amana, Crosley, Inglis, Admiral, Roper.

Part # WPW10006384 replaces these:

W10006384, WPW10006384VP.
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
Sort by:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Part Videos

Replacing your Whirlpool Washer Drive Belt

Customer Repair Stories
Average Repair Rating: 4.0 / 5.0, 4 reviews What's this?
Sort by:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Jerry from WALLA WALLA, WA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers, Socket set
Parts Used:
WPW10006384, W10721967
Noise on bottom of Washer louder as time went on. 1 1/2 years
Well, first investigated and found loose nut on drive clutch. First take off the two screws with nut drive then cover off using a screwdriver blade to snap off the cover. Then socket ratchet to take off the nut on drive clutch. take off belt by slowly rotating the drive gear. two screws that hold the electronics to the upper drive clutch and put aside, so you can snap off the cover for drive clutch on upper part with screwdriver and off the parts come and install whole unit back as took it apart. Line up the new upper clutch so that is position as was before. (Using parts diagram helps a lot as www. partsselect.com has for you or Maytag.com.) Then put the electronic part board back on and the gear and nut. Make sure it is tight by several attempts to make sure it's snugged up good and then slowly roll belt back on the pulley and motor drive. Put your cover guard back on with two screws and done.
33 of 45 people found this instruction helpful.
Was this instruction helpful to you?
Paul from E NORTHPORT, NY
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Socket set, Wrench (Adjustable)
Parts Used:
WPW10006384
Smelled a burning odor occasionally
First, I checked the belt before ordering and then decided to order the belt, capacitor, and clutch assembly (if I needed to replace). I replaced the belt noticing the older belt came right off and new one was tighter going on. I replaced the capacitor since I had it handy and it can be known to cause this smell also. After setting washer back up and started a cycle I noticed the spin cycle would not start properly so I thought maybe the capacitor (new one) was faulty or just not the exact match even though it was said to be. I replaced my older capacitor back on and again ran cycle and it ran great. Thus I decided to send the parts which were not used. I would recommend this site as I have used them in the past before on other items. They ship fast and have a great return policy if parts not used.
6 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Terry from HANCOCK, MD
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers
Parts Used:
WPW10006384
washer wasn't spinning after rinsing but the motor was running
I had taken the time to watch videos of this repair so when the switch arrived I knew what I had to do. Removing the screws to get the back cover off was simple as was installing the switch. No tricks here just watch the videos and your all set to do the job
4 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Joseph from BAKER, FL
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
Parts Used:
WPW10006384, W10721967
Loose pulley
Tightened up the pulley as the video showed me that might be the issue.
1 person found this instruction helpful.
Was this instruction helpful to you?
Customer Reviews
Average Rating:
12 Reviews
4.6
out of 5
Filter By Rating:
  • 5 Stars
    10
  • 4 Stars
    1
  • 3 Stars
    0
  • 2 Stars
    0
  • 1 Stars
    1
Sort by:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Model Cross Reference

This part works with the following models:

PartSelect Number: PS11747978
Manufacturer Part Number: WPW10006384
Brand
Model Number
Description
Kenmore
11020022010
Washer
Kenmore
11020022011
Washer
Kenmore
11020022012
Washer
Kenmore
11020022014
Washer - WASHER
Kenmore
11020102310
Washer - AUTOMATIC WASHER
Kenmore
11020102311
Washer - AUTOMATIC WASHER
Kenmore
11020112310
Washer - AUTOMATIC WASHER
Kenmore
11020112311
Washer - WASHER
Kenmore
11020222511
Washer - WASHER
Kenmore
11020232710
Washer - WASHER
Kenmore
11021102010
Washer
Kenmore
11021102011
Washer
Kenmore
11021102012
Washer
Kenmore
11021102013
Washer - AUTOMATIC WASHER
Kenmore
11021112010
Washer
Kenmore
11021112011
Washer
Kenmore
11021182010
Washer
Kenmore
11021182011
Washer
Kenmore
11021182012
Washer
Kenmore
11021202010
Washer
Kenmore
11021202011
Washer
Kenmore
11021252110
Washer
Kenmore
11021252111
Washer
Kenmore
11021292010
Washer
Kenmore
11021292011
Washer
Kenmore
11021292012
Washer
Kenmore
11021292013
Washer - AUTOMATIC WASHER
Kenmore
11021302010
Washer
Kenmore
11021302011
Washer
Kenmore
11021302012
Washer - WASHER