The front facing foot is sold individually. It is used on your washing machine and can also be known as an adjustable leveling leg. This specific front facing leveling leg has a rubber foot. It is important that when installing this part you are very careful, if not installed correctly your washer will be off balance which will then cause it to vibrate and/or shake during the cycle. The function of the adjustable foot is to keep your washing machine supported and to make sure that it is level at all times. The tools you will need for this repair include a pair of channel lock pliers, and a 9/16 wrench.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
June 3, 2019
Would this foot front leg fit on back of machine? I have no back legs on machine there gone.I am renting a home the machine was left here without legs.Washer works but need legs.
For model number 11047512602
Hello Jane, thank you for inquiring. This is also the Back Leg, and is compatible to your washer.
3 people found this helpful.
Was this helpful?
Thank you for voting!
October 11, 2019
What size (diameter) is the post? Is thread size 13 tpi?Thanks
For model number Maytag LA510
Hi Will, thank you for your question. Unfortunately we do not have the thread size. However this part is photographed on a 1 inch grid background. So the post is about 3/8" thick. However this part is not the correct part for your appliance according to the model number you provided. I have linked the correct part below for you. Good luck with your repair.
Machine moves and rocks unevan to the right. It appears sometime
For model number HAV4657EWW REV
Hello Michael, Thank you for the question. We suggest checking the Suspension Springs to see if there need to be replaced or have come undone. This package contains a new set of six springs. The suspension springs in your washer connect to the bottom of tub, and help to hold it in place. If you need help placing an order, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you!
Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
57 of 81 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
washer not rotating
Washer not rotating, removed the control head and back cover. Then removed body housing around tube to get to the bottom. had to replace coupling on motor then removed the agitator tower and replaced the Parts for the tower agitator. unit is 16 years young and still looks and runs new, put a total of 55 dollars into repair and it should be good for a long time. This is with a family of five. Washing 2 loads everyday.
I was familiar with the Kenmore / Whirlpool direct drive mechanism but at first I could not determine how to release the console. I finally found the end cap trim pieces would pop off revealing the 2 screws that hold the console in place. After removing them the console flips up and over the backboard. I then removed the 2 clips that hold the cabinet to the backboard, unpluged the lid switch connector and then tipped the entire cabinet forward and off the frame. This gives you access to the entire washing machine mechanism. Next I released the 2 metal clips that hold the pump on and push it out of the way leaving the hoses connected. Next I released the 2 clips that hold the pump on, these clips also have a screw to secure them. I was then able to set the motor to the side without removing any wires. The coupling parts had broken and were already off of the motor shaft and the input drive shaft of the transmission. I put the new drive parts on and had to tap them down untill they were flush with the end of the shafts. I then put the rubber coupling on the transmission drive end and aligned the motor drive to mate into the other holes in the coupling as I put the two back together. I then re attached the 2 motor clips with screws and reinstalled the pump with it's clips. I then reinstalled the cabinet onto the frame and replaced the cabinet clips. I then plugged in the lid switch connector and flipped the console back over and screwed it down. I then reinstalled the trim caps that had me stumped to begin with. The unit tested out OK.
The repair was simple as you can imagine. Thought I could buy these legs at any big box store or at least at the local hardware store. No such luck. Partselect had the right product---easy to order and easy to install. Things around here are great.