Part Location Diagram of WPW10001130 Whirlpool Foot, Front - Single
See part 34 in the diagram
Replacing your Whirlpool Washer Foot, Front - Single
( Grid squares measure 1x1 inch )
Customer Service Representative

Get in touch, we're here to help!

Monday to Saturday
8am - 9pm EST

customerservice@partselect.com

Foot, Front - Single WPW10001130

 Fits your GX900QPPB2!
★★★★★
★★★★★
4 Reviews

Rated by 6 customers 

Easy 

1- 2 hours 

Ratings submitted by customers like you who bought this part.

$ 7.44
  In Stock

Get this part fast! Average delivery time for in-stock parts via standard shipping: 1.8 days.

 Fits your GX900QPPB2!
PartSelect Number PS11747965
Manufacturer Part Number WPW10001130
Manufactured by Whirlpool for Whirlpool, Kenmore, Maytag, KitchenAid
Product Description

Foot, Front - Single Specifications

The front facing foot is sold individually. It is used on your washing machine and can also be known as an adjustable leveling leg. This specific front facing leveling leg has a rubber foot. It is important that when installing this part you are very careful, if not installed correctly your washer will be off balance which will then cause it to vibrate and/or shake during the cycle. The function of the adjustable foot is to keep your washing machine supported and to make sure that it is level at all times. The tools you will need for this repair include a pair of channel lock pliers, and a 9/16 wrench.
How Buying OEM Parts Can Save You Time and Money

How Buying OEM Parts Can Save You Time and Money

Part Videos

Replacing your Whirlpool Washer Foot, Front - Single

Replacing your Whirlpool Washer Foot, Front - Single
Troubleshooting
This part works with the following products:
Washer, Trash Compactor, Washer Dryer Combo, Dryer.
Part# WPW10001130 replaces these:
AP6014700, 14210041, 21031, 22001915, 22003544, 22003545, 22003546, 3-5087, 3-89102, 305087, 3359453, 386047, 388094, 388743, 389102, 41001098, 675021, 7-75526, 775183, 775526 , 776101, 80014, 8182826, W10001130, WPW10001130VP, Y389102, Y775526 Show less
Back to Top
Customer Reviews
Average Rating:
★★★★★
★★★★★
4 Reviews
5.0
Filter By Rating:
  • 5 Stars
    4
  • 4 Stars
    0
  • 3 Stars
    0
  • 2 Stars
    0
  • 1 Star
    0
Sort by:
  • 1
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
  • 1
Customer Repair Stories
 Average Repair Rating: 2.9 / 5.0, 6 reviews. What's this?
Sort by:
  • 1
Sorry, we couldn't find any existing installation instruction that matched.
Front legs were rotted.
Replace front legs. Very easy fix.
  • Cindie from DUNMORE, PA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Wrench (Adjustable), Wrench set
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Bought a washer without front leveling feet
The repair was simple as you can imagine. Thought I could buy these legs at any big box store or at least at the local hardware store. No such luck. Partselect had the right product---easy to order and easy to install. Things around here are great.
  • Rick from Lennon, MI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Wrench (Adjustable)
1 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
washer not rotating
Washer not rotating, removed the control head and back cover. Then removed body housing around tube to get to the bottom. had to replace coupling on motor then removed the agitator tower and replaced the Parts for the tower agitator. unit is 16 years young and still looks and runs new, put a total of 55 dollars into repair and it should be good for a long time. This is with a family of five. Washing 2 loads everyday.
Other Parts Used:
Foot, Front - Single Direct Drive Motor Coupling Hose Clamp Water Inlet Syphon Agitator Repair Kit
  • kaine from butler, PA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Pliers, Screw drivers, Wrench set
21 of 174 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken water inlet syphon combined with missing feet was causing water to spill out of the washer
I removed the back of the washer, removed the old water inlet syphon, replaced it with the new one, and, with some difficulty, replaced the back of the washer, reattaching all of the parts to it.
Other Parts Used:
Foot, Front - Single Water Inlet Syphon Leveling Leg Locking Nut
  • Randy from Atlanta, GA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
17 of 36 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Bearings went out in the drum.
purchased the bearings at Napa auto parts for 16$. Over all it was a little difficult to get the bearings out and back in. Used a brass drift to drive them out and to seat them back in..
Other Parts Used:
BASE BRACE- CRO Lower Front Panel Clip Adhesive Tub to Cabinet / Plate Spring Plastic Washer BRIDGE- SH Rear Strut Kit - Set of 2 Struts Rubber Foot Pad Spinner Support and Seal Kit Foot, Front - Single Locking Nut Screw
  • Paddy from Ferndale, WA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    More than 2 hours
  • Tools:
    Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
57 of 81 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
No agitation, No spin, pump OK
I was familiar with the Kenmore / Whirlpool direct drive mechanism but at first I could not determine how to release the console. I finally found the end cap trim pieces would pop off revealing the 2 screws that hold the console in place. After removing them the console flips up and over the backboard. I then removed the 2 clips that hold the cabinet to the backboard, unpluged the lid switch connector and then tipped the entire cabinet forward and off the frame. This gives you access to the entire washing machine mechanism.
Next I released the 2 metal clips that hold the pump on and push it out of the way leaving the hoses connected. Next I released the 2 clips that hold the pump on, these clips also have a screw to secure them. I was then able to set the motor to the side without removing any wires.
The coupling parts had broken and were already off of the motor shaft and the input drive shaft of the transmission. I put the new drive parts on and had to tap them down untill they were flush with the end of the shafts. I then put the rubber coupling on the transmission drive end and aligned the motor drive to mate into the other holes in the coupling as I put the two back together. I then re attached the 2 motor clips with screws and reinstalled the pump with it's clips. I then reinstalled the cabinet onto the frame and replaced the cabinet clips. I then plugged in the lid switch connector and flipped the console back over and screwed it down. I then reinstalled the trim caps that had me stumped to begin with. The unit tested out OK.
Other Parts Used:
Foot, Front - Single Direct Drive Motor Coupling
  • Ernest from Midlothian, VA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers
7 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • 1
Questions and Answers

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

3 questions answered by our experts.
Sort by:
  • 1
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Jane
June 3, 2019
Would this foot front leg fit on back of machine? I have no back legs on machine there gone.I am renting a home the machine was left here without legs.Washer works but need legs.
For model number 11047512602
PartSelect logo
Hello Jane, thank you for inquiring. This is also the Back Leg, and is compatible to your washer.

3 people found this helpful.

Was this helpful?
Thank you for voting!
Will
October 11, 2019
What size (diameter) is the post? Is thread size 13 tpi?Thanks
For model number Maytag LA510
PartSelect logo
Hi Will, thank you for your question. Unfortunately we do not have the thread size. However this part is photographed on a 1 inch grid background. So the post is about 3/8" thick. However this part is not the correct part for your appliance according to the model number you provided. I have linked the correct part below for you. Good luck with your repair.

1 person found this helpful.

Was this helpful?
Thank you for voting!
Related Parts:
Michael
February 15, 2022
Machine moves and rocks unevan to the right. It appears sometime
For model number HAV4657EWW REV
PartSelect logo
Hello Michael, Thank you for the question. We suggest checking the Suspension Springs to see if there need to be replaced or have come undone. This package contains a new set of six springs. The suspension springs in your washer connect to the bottom of tub, and help to hold it in place. If you need help placing an order, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you!

1 person found this helpful.

Was this helpful?
Thank you for voting!
Related Parts:
  • 1
You May Also Need ?
Model Cross Reference
This part works with the following models:
PartSelect Number: PS11747965
Manufacturer Part Number: WPW10001130
Brand
Model Number
Description
Kenmore
10682872600
Washer - Kenmore Washing Machine Model 106.82872600 (10682872600, 106 82872600) Parts
Kenmore
11010202000
Washer
Kenmore
11010202001
Washer
Kenmore
1101050299
Washer - Kenmore Washing Machine Model 110.1050299 (1101050299, 110 1050299) Parts
Kenmore
11010502990
Washer
Kenmore
11010502991
Washer
Kenmore
11010852990
Washer
Kenmore
11010852991
Washer
Kenmore
11012202100
Washer
Kenmore
11012502100
Washer
Kenmore
11012852100
Washer
Kenmore
11013202200
Washer
Kenmore
11013212200
Washer
Kenmore
11014102300
Washer
Kenmore
11014112300
Washer
Kenmore
11014202300
Washer
Kenmore
11014212200
Washer
Kenmore
11014222300
Washer
Kenmore
11014502300
Washer
Kenmore
11014852300
Washer
Kenmore
11015732400
Washer
Kenmore
11015842400
Washer - Kenmore Washing Machine
Kenmore
11015852400
Washer
Kenmore
11015862400
Washer
Kenmore
11015864400
Washer
Kenmore
11015942400
Washer
Kenmore
11015942401
Washer
Kenmore
11015944400
Washer
Kenmore
11015944401
Washer
Kenmore
11015952400
Washer
Customer Service Representative

Get in touch, we're here to help!

Monday to Saturday
8am - 9pm EST

Contact Customer Service