Foot, Front - Single WPW10001130 | Official Whirlpool Part | Fast Shipping | PartSelect
Foot, Front - Single – Part Number: WPW10001130
Foot, Front - Single – Part Number: WPW10001130 Foot, Front - Single – Part Number: WPW10001130 https://partselectcom.azureedge.net/Schematics/Maytag/IFMSPDID.gif

Foot, Front - Single

PartSelect Number PS11747965

Manufacturer Part Number WPW10001130

Manufactured by Whirlpool

Product Description

Foot, Front - Single Specifications

The front facing foot is sold individually. It is used on your washing machine and can also be known as an adjustable leveling leg. This specific front facing leveling leg has a rubber foot. It is important that when installing this part you are very careful, if not installed correctly your washer will be off balance which will then cause it to vibrate and/or shake during the cycle. The function of the adjustable foot is to keep your washing machine supported and to make sure that it is level at all times. The tools you will need for this repair include a pair of channel lock pliers, and a 9/16 wrench.

How Buying OEM Parts Can Save You Time and Money

Troubleshooting

This part fixes the following symptoms:

Shakes and moves

This part works with the following products:

Washer, Trash Compactor, Washer Dryer Combo, Dryer.

This part works with the following brands:

Whirlpool, Kenmore, Maytag, KitchenAid, Roper, Estate, Inglis, Amana, Crosley, Jenn-Air, Admiral, International, Magic Chef.

Part # WPW10001130 replaces these:

14210041, 21031, 22001915, 22003544, 22003545, 22003546, 305087, 3359453, 386047, 388094, 388743, 389102, 41001098, 675021, 775183, 775526, 776101, 80014, 8182826, AP6014700... Show More
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
2 questions answered by our experts.
Sort by:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Part Videos

Replacing your Whirlpool Washer Foot, Front - Single

Customer Repair Stories
Average Repair Rating: 2.7 / 5.0, 5 reviews What's this?
Sort by:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Paddy from Ferndale, WA
Difficulty Level:
A Bit Difficult
Total Repair Time:
More than 2 hours
Tools:
Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
Parts Used:
22003435, 22002767, WP22002239, WP22002123, 22002100, WP22002023, 22001993, 22001988, WP210684, W10181639, WPW10001130, WP62739, WP1163839
Bearings went out in the drum.
purchased the bearings at Napa auto parts for 16$. Over all it was a little difficult to get the bearings out and back in. Used a brass drift to drive them out and to seat them back in..
56 of 80 people found this instruction helpful.
Was this instruction helpful to you?
kaine from butler, PA
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers, Wrench set
Parts Used:
WPW10001130, 285753A, WP596669, WP3360977, 285811
washer not rotating
Washer not rotating, removed the control head and back cover. Then removed body housing around tube to get to the bottom. had to replace coupling on motor then removed the agitator tower and replaced the Parts for the tower agitator. unit is 16 years young and still looks and runs new, put a total of 55 dollars into repair and it should be good for a long time. This is with a family of five. Washing 2 loads everyday.
19 of 172 people found this instruction helpful.
Was this instruction helpful to you?
Randy from Atlanta, GA
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
Parts Used:
WPW10001130, WP3360977, WP3359452
Broken water inlet syphon combined with missing feet was causing water to spill out of the washer
I removed the back of the washer, removed the old water inlet syphon, replaced it with the new one, and, with some difficulty, replaced the back of the washer, reattaching all of the parts to it.
17 of 36 people found this instruction helpful.
Was this instruction helpful to you?
Ernest from Midlothian, VA
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers
Parts Used:
WPW10001130, 285753A
No agitation, No spin, pump OK
I was familiar with the Kenmore / Whirlpool direct drive mechanism but at first I could not determine how to release the console. I finally found the end cap trim pieces would pop off revealing the 2 screws that hold the console in place. After removing them the console flips up and over the backboard. I then removed the 2 clips that hold the cabinet to the backboard, unpluged the lid switch connector and then tipped the entire cabinet forward and off the frame. This gives you access to the entire washing machine mechanism.
Next I released the 2 metal clips that hold the pump on and push it out of the way leaving the hoses connected. Next I released the 2 clips that hold the pump on, these clips also have a screw to secure them. I was then able to set the motor to the side without removing any wires.
The coupling parts had broken and were already off of the motor shaft and the input drive shaft of the transmission. I put the new drive parts on and had to tap them down untill they were flush with the end of the shafts. I then put the rubber coupling on the transmission drive end and aligned the motor drive to mate into the other holes in the coupling as I put the two back together. I then re attached the 2 motor clips with screws and reinstalled the pump with it's clips. I then reinstalled the cabinet onto the frame and replaced the cabinet clips. I then plugged in the lid switch connector and flipped the console back over and screwed it down. I then reinstalled the trim caps that had me stumped to begin with. The unit tested out OK.
7 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Rick from Lennon, MI
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Wrench (Adjustable)
Parts Used:
WPW10001130
Bought a washer without front leveling feet
The repair was simple as you can imagine. Thought I could buy these legs at any big box store or at least at the local hardware store. No such luck. Partselect had the right product---easy to order and easy to install. Things around here are great.
0 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Customer Reviews
Average Rating:
1 Review
5
out of 5
Filter By Rating:
  • 5 Stars
    1
  • 4 Stars
    0
  • 3 Stars
    0
  • 2 Stars
    0
  • 1 Stars
    0
Sort by:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Model Cross Reference

This part works with the following models:

PartSelect Number: PS11747965
Manufacturer Part Number: WPW10001130
Brand
Model Number
Description
Kenmore
10682872600
Washer - Kenmore Washing Machine Model 106.82872600 (10682872600, 106 82872600) Parts
Kenmore
11010202000
Washer
Kenmore
11010202001
Washer
Kenmore
1101050299
Washer - Kenmore Washing Machine Model 110.1050299 (1101050299, 110 1050299) Parts
Kenmore
11010502990
Washer
Kenmore
11010502991
Washer
Kenmore
11010852990
Washer
Kenmore
11010852991
Washer
Kenmore
11012202100
Washer
Kenmore
11012502100
Washer
Kenmore
11012852100
Washer
Kenmore
11013202200
Washer
Kenmore
11013212200
Washer
Kenmore
11014102300
Washer
Kenmore
11014112300
Washer
Kenmore
11014202300
Washer
Kenmore
11014212200
Washer
Kenmore
11014222300
Washer
Kenmore
11014502300
Washer
Kenmore
11014852300
Washer
Kenmore
11015732400
Washer
Kenmore
11015842400
Washer - Kenmore Washing Machine
Kenmore
11015852400
Washer
Kenmore
11015862400
Washer
Kenmore
11015864400
Washer
Kenmore
11015942400
Washer
Kenmore
11015942401
Washer
Kenmore
11015944400
Washer
Kenmore
11015944401
Washer
Kenmore
11015952400
Washer