Wash Impeller WP99002659

This site has a great video on how to do this. Just follow that.

I followed the instructions here on PartSelect to dismantle and put the new impeller in to place. Could tell the difference just in sound alone once it was running.

Followed video to remove impeller, motor, seal and chopper. Replaced per video. Decided to replace motor gasket to ensure no future leaks. Everything went really smooth and no longer have the noise when running the dishwasher. The only pain was working around the door.

In order to clean the screen I had to remove the impeller. Removal required using a wheel puller. I backed off on the impeller screw but left it attached so that the wheel puller could pry against it. I then tightened the puller enough to free the impeller. I was then able to unscrew and remove the screen for cleaning.

also had to replace heating element. Had to remove dishwasher from under counter to get to heat element. Initial installer used long braided steel water line and plug in electrical connection so removal was easy (10 min). Pulled (2) electrical terminals from heat element and (2) plastic retaining nuts put in new element w/matching nuts,element came w/seals. Check for leaks before installing back under counter. Then removed torx screws holding impeller cover and accumulator/filter removed old put in new after good cleaning of course. All is well.

Impeller bolts to plastic chopper mount which is screwed to the top of the motor. Threads on chopper mount were stripped causing impeller to not spin fast enough (replacement mount, which is part of the chopper kit, is metal). Installtion was not difficult.
You have to reach underneath the washer and wedge a screwdriver on top of the motor to hold the shaft from moving.

took the bottom spray arm & lower plastic pieces out, unscrewed the impeller & replaced it. the original impeller which holds the disposal blade down & wore down & no longer retained the blade. snap.

I took out the racks and disassembled the bottom assembly until I got to the impeller. Just replaced the part and reassembled. I used only a star shaped driver on all tightened pieces. It was very easy to do and I did not even need any advice/help from the hubby! Saved a whole lot of time and money doing this small repair myself. Thanks for fast service. I ordered part online Thur. late afternoon, and it arrived Friday.

First of all I shut the power off to the dishwasher at the breaker box. Turn the water off to the dishwasher. Unhook the water line and then remove the screws that go around the outside trim edge of the dihwasher that secures it to the cabinets. Then you will want to look at the adjustable legs on the dishwasher. You may need to lower the legs to get the dishwasher out from underneath the counter top. While you are doing this you should also pay attention to your drain hose. My drain hose had plenty of slack so I was able to pull my dishwasher out from underneath the cabinet and then unhook it. You should have towels or a bucket in place to catch any water that is inside the drain hose. Next I laid the dishwasher over on its left side and I was able to access the pump. I then used a flat screw driver to remove the hose clamp and remov the drain hose from the pump. I then unplugged 1 wire connector and a bracket and could turn the pump counter clockwise and removed it from the dishwasher. There is a bracket that must be removed from the old pump to the new pump. Once this is accomplished You are ready to reinstall the new pump. I took a towel and wiped the area where the pump hooks into the dishwasher to make sure all debris was removed. I then used a very small amount of gasket sealer and placed it around the "O" Ring on the new pump. Next place the pump back in the whole and turn in a clock wise direction securing it back into the dishwasher. Hook up the drain hose and the wire connector. Make sure the bracket is postioned properly and you are ready to put dishwasher back under the counter.

I'm telling this story for my husband who is a pretty handy guy--I watched him do the repair. I had had someone out to look at the dishwasher and they said it would be $284 to fix this one little thing because you couldn't buy the one little part separately, you had to buy a whole new motor. Since the dishwasher is old, it didn't make sense to invest this much in it--might as well buy a new one for that kind of money. My husband did some looking around and found the part on your site and installed it himself. So the cost was under $40. The dishwasher is now working better than it had been for a while.