Whirlpool/Whirlpool_Thumb/2GGFKMJN.gif
See part 2 in the diagram
Replacing your KitchenAid Range Element, Broil play video
( Grid squares measure 1x1 inch )

Get in touch, we're here to help!

Open until 12am EST

customerservice@partselect.com

Element, Broil

★★★★★
★★★★★
21 Reviews
$ 156.17   In Stock

Get this part fast! Average delivery time for in-stock parts via standard shipping: 1.8 days.

 Fits your KEBS207SSS04!
 Fits your KEBS207SSS04!
PartSelect Number PS11747304
Manufacturer Part Number WP9760774
Manufactured by Whirlpool
Product Description

Element, Broil Specifications

This broil element is found on the roof of the oven. The broil element is at the top of the oven and supplies the heat to broiling. 14" x 15" with 1-3/8" inserts. This part works with the following brands: Whirlpool, Roper, Admiral, Maytag, Hardwick, Jenn-Air, Estate, Magic Chef, Crosley, Inglis, Norge, Modern Maid, Amana, Kenmore, KitchenAid, Caloric.
How Buying OEM Parts Can Save You Time and Money play video

How Buying OEM Parts Can Save You Time and Money

Troubleshooting
This part fixes the following symptoms:
Element will not heat | Little to no heat when broiling | Little to no heat when baking | Oven not heating evenly
This part works with the following products:
Range, Wall Oven, Microwave Oven Combo.
This part works with the following products:
KitchenAid, Crosley, General Electric, Maytag.
Part# WP9760774 replaces these:
AP6014070, 8301514, 9760774
Questions and Answers

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

8 questions answered by our experts.
    Sort by:
    Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
    Yvonne
    October 2, 2017
    Range broil element has bent downwards on the front. It still glows but it looks like it melted somewhat and has slight bubbles on the front end, I tried to bent it back up as far as I could. Now to replace this element will the whole built in oven unit (electric oven on bottom and microwave attached on the top) have to be removed from the wall? Or can the broiler element be replaced from the inside of the oven? Please advise. Thank you.
    For model number KEMS308SSS05
    Hi Yvonne, Thank you for the question. Yes you have to remove the oven from the wall in order to access the wires and connections in the back. Hope this helps!

    6 people found this helpful.

    Was this helpful?
    Thank you for voting!
    Bruce
    November 22, 2017
    How do you connect the wires to the broiler heating element for a double wall oven inside a cabinet? Do you have to pull out the oven to access the back?
    Hi Bruce, Thank you for your question. There is a video listed with the broil element on our website that you may reference on how to install it. I hope this helps. Thank you and have a great day!

    2 people found this helpful.

    Was this helpful?
    Thank you for voting!
    Charles
    January 15, 2020
    Does the top oven of a double oven unit have to be removed from it’s insert, just as a free standing unit has to be pulled out from the wall?
    For model number KEBS208SSS04
    Hello and thank you for writing. Yes, it does you are correct. For access to the wires of the element, you will need to pull the appliance out from the wall. We hope this helps. Please contact us anytime if you require further assistance.

    2 people found this helpful.

    Was this helpful?
    Thank you for voting!
    Wickham
    February 17, 2020
    How do i replace the broiler element?
    For model number YKERS807SS00
    Hello Wickham, Thank you for your question. First, you will need to Disconnect the two connectors on each side of element. Second, remove the screws that were too rusted by using a screwdriver with vise grips. Third, remove the old element, then insert the new element through the holes in rear of the oven. We hope this helps.

    Was this helpful?
    Thank you for voting!
    Charles Shackleford
    March 2, 2020
    Can this element be changed out from inside or will the oven have to be removed to get to the electric wires to connect the 4 connectors?
    For model number KEBS208SSS04
    Hello Charles, thank you for your question. Per the installation video on our site of that part you would have to access the back to remove the electric wires that connect to the unit. I hope this helps.

    Was this helpful?
    Thank you for voting!
    Victor Agresti
    December 10, 2021
    When baking do both elements heat up,my oven takes forever to heat up coil never gets red
    For model number KEBK171SSS4
    Hi Victor, Thank you for your question. When the bake cycle is in use for most electric ovens, both the bake and broil elements will regulate the temperature inside the oven. If the oven is not heating correctly the issue may be with the oven sensor. The oven temperature sensor is the part that monitors the oven temperature and signals the electronic control board to turn the elements on and off. Before removing this part from the oven and testing it with a multimeter for continuity, unplug the oven from the electrical outlet. To test the sensor, you will need to reference your owner’s manual to determine what the correct reading should be for your model, as this varies from model to model. To test it for continuity, use a multimeter on the Rx1 setting and touch the terminals with the probes. This test needs to be done with the sensor at room temperature to produce accurate results. If your test results do not meet the manufacturer’s guidelines, you need a replacement temperature sensor. If the sensor is fine, you will need to check the elements, the electronic control board and the wiring between the parts to see which one is causing the issue. We hope this helps! If you have any questions, please let us know.

    Was this helpful?
    Thank you for voting!
    Related Parts:
    Rick
    March 15, 2022
    Heating element sparking
    For model number KEMS308SSSOO
    Hi Rick, Thank you for your question. If the broil element is sparking it will need to be replaced. The part number listed under your model number for the broil element is PS11747304. If you need help placing an order for it, customer service is open 7 days a week and anyone will be happy to assist you. Please feel free to give us a call. We look forward to hearing from you!

    Was this helpful?
    Thank you for voting!
    Related Parts:
    Ruth
    May 31, 2019
    The video you have provided for this part has the person take out the stove from the wall to do a few things in the back. How would it work for a wall oven.
    For model number KEMS308SBL00
    Hello Ruth, Thank you for the question. The wall oven will also need to be removed from the wall. Hope this helps!

    Was this helpful?
    Thank you for voting!
      Part Videos

      Replacing your KitchenAid Range Element, Broil

      Replacing your KitchenAid Range Element, Broil play video
      Customer Repair Stories
       Average Repair Rating: 3.6 / 5.0, 13 reviews. What's this?
      Sort by:
      Sorry, we couldn't find any existing installation instruction that matched.
      The broiler element in my wall oven burned out
      This was easy and I'm glad I didn't go to the trouble and expense of hiring an appliance repair person. I'm reasonably handy, but I really have no experience in this kind of repair. I'd like to mention that the part I ordered arrived in just two days and it was exactly the right part, so I was very pleased in that regard.

      After turning off the circuit to the wall oven and confirming that the power was off, I had to remove the oven from the wall in order to access the wires and connections in the back. Normally, this wouldn't have been necessary because usually the broiler element can be disconnected from the clasps that connect it to the electric source by simply unscrewing the defective element from the roof of the oven, pulling gently on the connection ends from inside the oven cavity in order to "pull out" an inch or two of the electric source wires and the metal clasps that accept the "male" connecting ends of the broiler element. Once the a bit of the wire and the metal connecting clasps are exposed and able to be held with pliers, the element can be disconnected from the connector clasps by simply pulling on the prongs of the element (hard).

      But in my case, one of the metal connecting clasp for one of the wires had melted, presumably when the element burned out, and that clasp could only be accessed and replaced from the back of the oven. Also, I would imagine that the wires and clasps could "slip" back behind the unit when they're disconnected if that's not done carefully. However, removing the wall oven was pretty easy for me -- even as a one-person job. I just put a tall table in front of it and slid it out so that it rested on the table.

      If you have to replace a metal connector clasp, they're inexpensive and available in the electrical departments of hardware/home stores.

      In my case, there's a metal panel at the back of the oven that had to be unscrewed and removed so that I could access the areas where the electrical source wires connect through the back wall of the oven to the broiler element. This was just a matter of removing a few screws and then removing the metal panel.

      Once the metal panel at the back of the oven was removed, I was able to replace the melted connection clasp by using a wire cutter/stripper and then pliers to secure the clasp on the end of the exposed wired by deforming the clamp with the pliers. Once that was done, I simply removed the screws that held the broiler element to the top of the oven cavity, disconnected the remaining three clasps that connect the element to the source wires (the fourth clasp was the one that had melted and that I'd replaced), removed the defective element, inserted the four "male" prongs of the broiler into the four clasps that connect them to the source wires, replaced the metal panel at the back of the oven, screwed the new element back into the top of the oven, slid the oven back into the wall cavity, turned the circuit back on, crossed my fingers, and everything worked like a charm.

      I saved a money, but more importantly (for me) I saved a lot of time that I would have had to have spent waiting around for a repair person.
      • David from Catonsville, MD
      • Difficulty Level:
        Easy
      • Total Repair Time:
        15 - 30 mins
      • Tools:
        Pliers, Screw drivers, Wrench set
      25 of 27 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      Broil element burned out/temp sensor questonable
      I followed instructions from the videos provided on the Part Select site. As with many such appliances, parts are interchangeable between brands. this unit is a KitchenAid but Whirpool,Kenmore parts interchange...Access from the front is all that's needed however and the only tool required was a phllips head screw driver...the only negative surprise (which the video warned about but I ignored) was the risk of the element leads drawing back through the holes, which 2 did. Save yourself that trouble by securing the wires to the back oven wall with a small strip of duct tape until you're ready to re-attach them to the new element. This necessitated removing the oven entirely for access to the back; the most time consuming aspect being removing/replacing what seemed like 20 odd screws holding the back cover in place! If not for that mistake, entire job would have been under 30 minutes. Well worth the effort and would do it again!
      Other Parts Used:
      Temperature Sensor
      • Stephen from HOUSTON, TX
      • Difficulty Level:
        Easy
      • Total Repair Time:
        30 - 60 mins
      • Tools:
        Screw drivers
      10 of 11 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      Broiler element not working
      Removed back of oven. Disconnected 2 connectors on each side of element. Removed screws that were too rusted to use screwdriver with vise grips. Removed old element, inserted new element through holes in rear of oven.Installed 1 screw on each side of element in rear and 2 screws in front where brackets support the front of the element.Put back panel back on. Push oven back in place, plug back in outlet.It works great and I didn't have to pay service man.
      Other Parts Used:
      Screw
      • James from Dublin, PA
      • Difficulty Level:
        Really Easy
      • Total Repair Time:
        15 - 30 mins
      • Tools:
        Screw drivers
      9 of 15 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      broiler element broke into
      There were 4 screws to remove and 2 wires to disconnect. We placed the order on line for replacement. It arrived the next day. We simply installed the new element by connecting the 2 wires (very easy) and putting the 4 screws back in place. It works like new and was sooo easy.
      • Salle from Marietta, GA
      • Difficulty Level:
        Really Easy
      • Total Repair Time:
        Less than 15 mins
      • Tools:
        Screw drivers
      8 of 12 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      Smaller broiler coil stopped working.
      Our double-oven is wall-mounted, so accessing the backside to change the wires (as shown in the instruction video) was not a practical do-it-yourself option. After turning off the circuit breaker and disconnecting the broken broiler element, it is pretty easy to pull the four connection wires through the backside of the oven, which allowed us to disconnect the slide clips. We attached twist-ties to each clip/wire before disconnecting to keep the clips/wires from pulling back behind the oven wall when moving the new element into position. We found it necessary to crimp a few clips onto the new element to make secure connections, but the rest of the project went pretty much as shown in the video and the new element works great.
      • Patrick from SANTA CLARA, CA
      • Difficulty Level:
        Easy
      • Total Repair Time:
        30 - 60 mins
      • Tools:
        Pliers, Screw drivers
      5 of 5 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      Center broiler element burned out
      Removed oven door for easy access. Removed 4 phillip head screws that held broiler element from top of oven. pulled wires a couple of inches out from back of oven and used flat screw driver to help separate the wires connecting the broiler from the oven. Did the opposite to install the new element,.
      The best part of this operation was the fact that the part arrived from Part Select by Fed X the next day after ordering it all for a shipping cost of $8.75. Great Service Highly recommend Part Select.
      • Ronald from DAVIS, CA
      • Difficulty Level:
        Really Easy
      • Total Repair Time:
        30 - 60 mins
      • Tools:
        Pliers, Screw drivers
      3 of 3 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      Baking element failed
      Remove the oven from the wall
      Remove the rear panel
      Remove the 2 bottom panels
      Lift and fold back the insulation
      Remove the element enclosure
      Replace the element
      Reverse the steps to assemble

      * the oven would not preheat and the top elements were working
      • ROBERT from BISMARCK, ND
      • Difficulty Level:
        A Bit Difficult
      • Total Repair Time:
        1- 2 hours
      • Tools:
        Nutdriver
      2 of 2 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      Burned out broiler element
      The Youtube videos for this particular repair, using part number PS11747304, indicated that the whole oven unit should be pulled out of the wall while working on it, and the electrical clips removed and re-attached from the back.

      Because I was doing this as a one-man job, and didn't have anything to place the oven on while working, I turned off the circuit breaker, and performed the entire element replacement from the front.

      1. I was very careful after unscrewing the 4 mounting screws (two in the back, two on the top) to gently pull the attaching wires while still attached to the old element.

      2. I had 4 mini vice-grips that I clamped (gently) on the insulation of the 4 wires before detaching them from old element. The vice grips prevented the wires from disappearing to whence they came.

      3. After completing the old element removal, I replaced it with the new element, attaching each wire where they had been attached to old element, only then removing the corresponding vice grip.

      4. With all 4 wires reattached, I carefully pushed the element ends back into the back of the oven... also avoiding the protruding temperature sensor. The element needed to be held in place by hand until the first overhead screw could be re-screwed.

      5. The most difficult part of the procedure was actually getting the screws to line up with their holes in the oven body. .. Returning the screws in fact took about half the 30 minutes the whole job took, because their alignment wasn't "keyed" such that the holes easily just lined up. My order was "Top right" - "Back Left", "Top Left", "Back Right".

      Once the 4 screws were all satisfactorily tightened back in place, I turned the breaker back on, and hit the pre-heat function on the oven... It smoked a very little (my hands may have been a bit oily) but that quickly dissipated, and the job was complete. I am very thankful that I didn't have a professional come out. My baker wife has used the oven 10-20 times since then, and it seems as good as new.
      • Brian from SEATTLE, WA
      • Difficulty Level:
        Easy
      • Total Repair Time:
        30 - 60 mins
      • Tools:
        Screw drivers
      2 of 3 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      Oven upper heating element went out.
      Turned the breaker off to the stove.
      Removed 4 screws holding the element in place.
      Disconnected the electric connection from element.
      I had to replace the screws which were corroded.
      Connect the new element electric connection.
      Replace the 4 screws.
      Turn on the power.
      Turn on oven to burn off the smell of the new element.
      You are done.
      • Lewis from WICHITA, KS
      • Difficulty Level:
        Really Easy
      • Total Repair Time:
        30 - 60 mins
      • Tools:
        Screw drivers
      1 person found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      Broiler quit broiling
      Turned off circuit breaker to oven
      Removed oven door
      Removed screws of reflector plate and top and back of oven
      Gently pulled element out and down slightly
      Removed slide crimps on wires
      Replaced reflector plate on new element
      Connected slide crimps on wires
      Screwed reflector plate with new element to top and back of oven
      Done. Total time 22 minutes
      Tested and it’s perfect!
      Other Parts Used:
      Screw
      • Linda from BOLIVAR, TN
      • Difficulty Level:
        Really Easy
      • Total Repair Time:
        15 - 30 mins
      • Tools:
        Screw drivers
      1 person found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      Customer Reviews
      Average Rating:
      ★★★★★
      ★★★★★
      21 Reviews
      4.6
      Filter By Rating:
      • 5 Stars
        16
      • 4 Stars
        2
      • 3 Stars
        2
      • 2 Stars
        1
      • 1 Star
        0
      Sort by:
      Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
      Model Cross Reference
      This part works with the following models:
      PartSelect Number: PS11747304
      Manufacturer Part Number: WP9760774
      Brand
      Model Number
      Description
      Crosley
      CT15G4Q
      Refrigerator
      KitchenAid
      KDRS807SSS00
      Range
      KitchenAid
      KDRS807SSS01
      Range
      KitchenAid
      KDRS807SSS02
      Range
      KitchenAid
      KDRS807SSS03
      Range
      KitchenAid
      KDRS807SSS04
      Range
      KitchenAid
      KDRS807SSS05
      Range
      KitchenAid
      KDRS807XSP00
      Range
      KitchenAid
      KDRS807XSP01
      Range
      KitchenAid
      KDSS907SSS00
      Range
      KitchenAid
      KDSS907SSS01
      Range
      KitchenAid
      KDSS907SSS02
      Range
      KitchenAid
      KDSS907SSS03
      Range
      KitchenAid
      KDSS907SSS04
      Range
      KitchenAid
      KDSS907SSS05
      Range
      KitchenAid
      KDSS907XSP00
      Range
      KitchenAid
      KDSS907XSP01
      Range
      KitchenAid
      KEBC167MSS00
      Wall Oven
      KitchenAid
      KEBC167MSS01
      Wall Oven
      KitchenAid
      KEBC167MSS02
      Wall Oven
      KitchenAid
      KEBC167MSS03
      Wall Oven
      KitchenAid
      KEBC167MSS04
      Wall Oven
      KitchenAid
      KEBC167VSS00
      Wall Oven
      KitchenAid
      KEBC167VSS01
      Wall Oven
      KitchenAid
      KEBC167VSS02
      Wall Oven
      KitchenAid
      KEBK101SBL00
      Wall Oven
      KitchenAid
      KEBK101SBL02
      Wall Oven
      KitchenAid
      KEBK101SBL04
      Wall Oven
      KitchenAid
      KEBK101SSS00
      Wall Oven
      KitchenAid
      KEBK101SSS02
      Wall Oven

      Get in touch, we're here to help!

      Open until 1am EST

      Contact Customer Service