Inside oven door glass was broken and door was not closing completely.
I removed the door from the oven by locking the hinges with the built-in locks leaving the door open about 20 degrees. the door can then be lifted slightly off the hinges and pulled out at the bottom while tilting the top inward to remove it from the oven. With the door laying on a suitable surface with the outside face down, I removed a
... Read morebout 6 or 8 screws from the door inside panel freeing the springs and the inside panel from the middle and front panels. Care must be taken to note from which locations the pointed self-taping screws come as opposed to the narrower-thread machine screws that hold the springs. Note: The inside panel does not need to be removed! Once the inside panel is freed from the inner panels, using suction cups the glass can be lifted slightly and slid toward the bottom of the door, rotated slightly, and removed through the window hole in the back face of the door. The new glass is installed in a similar way using suction cups by maneuvering it at a angle through window hole and into its frame. The hinges were replaced by lifting the bottom of the inner door panel slightly to clear the hinge and swapping in the new ones. Be sure to observe the difference between the left and right hinges in the location of the screw hole at the bottom of each hinge The narrow-thread machine screws that hold the hinges to the inside panel should be installed first while you can get you hand inside the door to hold each hinge in alignment with the screw holes while you start each screw. Re-install the pointed self tapping screws by pressing down on the rear panel to collapse the spring-action glass frames within the door so that the short screws will reach their threaded hole. Be careful to back off the self tapping screws first until you feel a click into the original threads to avoid stripping the holes. Last re-install the door on the oven. The replacement hinges should have come with the springs already "cocked" with the built in locks in place. Install the door with it in tan almost-closed position by sliding the hinge extensions into the slots in the oven. Once the extensions are properly in the slots the door can be fully opened and the built-in hinge locks re-positioned to the unlocked position to allow the door to fully close. Should you accidentally release only one of the hinge locks in trying to insert the hinge extensions into the slots you will have to reset the hinge. If the door is free from the oven, this may require a pair of heavy pliers, like channel lock pliers, to re-tension the hinge spring and "cock" the hinge extension by re-positioning the built-in lock in the locked position. If the hinge lock on one side of the door releases, but the the opposite side hinge extension is not fully inserted into the oven slot I recommend carefully moving the door to the fully open position, being careful to avoid twisting the inserted spring's extension, so that the hinge lock can be re-positioned to the locked position, the door full removed, and start again to install it. It helps to have two persons to hold opposite sides of the door for this operation as the door is heavy, but not essential. When in the proper position the hinge extensions may not appear fully inserted, but this is normal to allow for closing of the built in locks. It helps to observe how much of the hinge extension is exposed either before removing the door initially, or, if you have a double oven, looking at the hinges on the door of the other oven. Good luck with your repair.
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
1 question answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
James Poli
August 6, 2018
Are the right and left door hinges the same for the Kenmore double oven?
For model number KEBC208KSS04
Hello James, thank you for your question. The right and left door hinges are different parts. Door Hinge - Right Side is Part Number: PS11747291 and Door Hinge - Left Side is Part Number: PS11747292. Good luck with your repair!