Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Richard D - June 5, 2019
Verified Purchase
1/4” diameter rubber bumper cost $16 with shipping
10 cent part cost almost $5 and took a week to get here after an additional $ 7 shopping fee. Another ting plastic screw seat $5. Together two tiny plastic parts cost $16 with shipping.
★★★★★
★★★★★
Myron S. G - April 8, 2019
Verified Purchase
easy, simple, exactly what I needed
came as expected, was the right part, easy installation.
★★★★★
★★★★★
Bob D - May 24, 2018
Verified Purchase
Lid Bumper
Exact part that was ordered arrived and was easy to install.
★★★★★
★★★★★
George F - March 23, 2018
Verified Purchase
Just snapped in; problem solved!
Received as requested and promised.
< Prev
1
Next >
Customer Repair Stories
Average Repair Rating: 3.1 / 5.0, 4 reviews.
What's this?
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
broken timer knob and lid bumper
the timer knob shaft must be held in place from spinning while the knob hub is removed, simply grasp the shaft with needle nose pliers below whats left of the hub and with another pair of pliers grasp what is left of the knob hub and rotate counter clockwise, once it is broken free it should spin right off. Reverse this process to install
... Read more the new timer knob. Installing the lid bumper is simple just pull out the old bumper with needle nose pliers and start the new bumper in from the bottom of the lid and work bumper until the bumper clears the hole in the lid, you may need a small flat screwdriver to work it in gently as not damage the finnish or the bumper when you clear the thicker part of the bumper flange it will lock right into the lid.
Repair was easy. Removed two side panels on the control plate. Removed two phillips screws that hold the control panel to the body of the washer. Disconnected the electic connection to the wires leading to the lid switch. Three sided of the lower cover lift over and removed from the washer frame. Access to the lid switch and wire ret
... Read moreainers was easy. Removed two screws holding the remaining parts of the switch and replaced with new. Re-routed the wires through the retainers. Set the sides back on making sure the set all the way back in the frame and fit properly into the plastic strips on the back of the washer. Reconnected wires, screws and end caps.
Using kit 285587 was straight forward. Removed fabric softener dispenser & sealing cap. It took more time to find the socket set (needed a 7/16 socket) with a long driver (10 inch) than to unscrew & remove the auger & agitator. Cleaned up the bowl whilst it was apart (good buildup of junk under the agitator). Replaced agitator, new t
... Read morehrust washer to find that grease should be applied but isn't included in kit (get part not 350849). Grrr.... Applied new auger, cam, dogs and holder. (No instructions in kit for assembling cam, dogs & holder, but you can work it out ok). Applied new bolt & washer, new seal on cap. Installed fabric softener. Could have been a 15 minute job but peace and quiet in the garage makes it worthy of taking longer ;-)
Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
22 of 233 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
Next >
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
4 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Brian
July 29, 2019
Why does my washer make so much noise during the spin cycle? When spinning it sounds like the drum is hitting against the cabinet. Also, when I move the drum by hand it seems loose to me. I checked the insides and everything seems to be where it belongs. Any solutions?
For model number MVWC416FW0
Hi Brian,
Thank you for your question. If the drum is sounds like it is banging against the cabinet during the spin cycle and it seems loose when you turn it by hand, the issue could be the drive belt. It is either loose, not positioned correctly on the pulley or it is worn out. You should also also check the pulley to see if it is worn or loose as well. I hope this helps. Thank you and have a great day!
2 people found this helpful.
Was this helpful?
Thank you for voting!
Robert
October 31, 2019
Washer fills and drains but no spin. Belt on and tight. What other part options do I have for to be cause. Regards Robert
For model number ITW4671EW0
Hello Robert, Thank you for the question. I suggest testing the Washing Machine Door Lock Assembly PartSelect Number PS12704713. If defective it may not pick up the lid is closed and preventing it from spinning. Hope this helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Lawrence
November 4, 2019
It is extremely noisy when going into the spin cycle after a wash or a rinse. The washer is so noisy, that I have to wear hearing protection when entering the laundry room.
For model number 110.20222510
Hi Lawrence,
Thank you for your question. If the washer is noisy going into the spin cycle, you may have to check the suspension rods to see if they worn or damaged. If they are, you will need to replace them. I hope this helps. Thank you and have a great day!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Jack
October 31, 2019
Washer makes a lot of noise when its in thespin cycle
For model number RTW4641BQ1
Hello Jack, thank you for writing. This is likely due to either a faulty Washer Drive Pulley, part number PS10057144, or Drive Block, part number PS11741977 for your washer. Good luck with your repair!
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
