Whirlpool/Whirlpool_Thumb/3VKCFT2L.gif
See part 13 in the diagram
( Grid squares measure 1x1 inch )

Get in touch, we're here to help!

Open until 10PM EST

customerservice@partselect.com

V-Style Cogged Tooth Pump Belt

$20.28   In Stock

Get this part fast. Average delivery time via standard shipping: 1.8 days.

PartSelect Number PS11746889
Manufacturer Part Number WP95405
Manufactured by Whirlpool
Troubleshooting
This part fixes the following symptoms:
Burning smell | Pumps but will not spin | Will not drain
This part works with the following products:
Washer.
This part works with the following products:
Kenmore, Whirlpool.
Part# WP95405 replaces these:
16192, 16358, 21012, 26000095405, 8201, 91261, 95405
Questions and Answers

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

2 questions answered by our experts.
    Sort by:
    Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
    Andy
    October 31, 2017
    Like to receive installation instructions
    Hi Andy, Thank you for the question. First turn off water. Disconnect electrical supply and water hoses. Remove agitator and cap. Lay machine on it's front. Do not leave it over night on it's front as some oil will leak out the breather hole on top of the transmission.Remove rear service panel. Loosen both nuts holding the motor mounting bracket in the base plate.Rotate the motor to the right to relieve the belt tension and remove belt from motor pulley.After belt is removed, rotate the motor to the left as far as possible to assure cam bar clearance.The spin cam bar must be advanced to the spin position. You can do this by pushing up on the spin control solenoid plunger and rotate the main drive pulley until the cam bar advances to the spin position.Remove the brake spring from the gear case cover and yoke.Remove the 3 support braces attached to the gear case and base plate.Remove the 2 pump mounting bolts. The pump hoses do not have to be removed.Remove the gear case mounting stud and spacer. Loosen the remaining 2 gear case mounting studs.Remove yoke retainer from yoke support. The gear case can now be pulled down so that the belt can be removed out between the top of of the clutch shaft and the clutch yoke, hen through the space under the stud. Drop the belt from around the gear case.Reverse the procedure in steps to install the new belt. Replace the pump making sure the pump lever is engaged in the slot in the agitator cam bar before securing the pump to the gear case. Grasp the bottom loop of the yoke spring with a pair of pliers and insert the spring in the hole in the upper gear case cover. Replace spacer in short gear case mounting stud. Finger tighten the 3 gear case mounting bolts . Set the machine upright and tighten the gear case mounting bolts securely. This procedure will allow the structure to align itself with the center post bearing. Lay the machine on it's front to mount the 3 support braces to the gear case base plate and tighten the bolts securely. To adjust the belt tension properly, position the belt over the pulleys. Insert a hammer handle or something similar between the motor mounting brackets. Rotate the motor as far as it will go to the left. Tighten the motor mounting bracket nuts. Check the tension of the belt, it should be about 1/2 inch.Set machine upright. Reinstall the agitator,service panel and water supply and plug the appliance back into the outlet. Good luck with the repair!

    2 people found this helpful.

    Was this helpful?
    Thank you for voting!
    Jean
    July 31, 2019
    Hello! I own an old Inglis uo 44600 dating from the mid 80s. The driving belt broke, model fsp 95405 and i wanted to make sure this one will be a perfect fit. Thanks in advance and have yourself a great day!!
    For model number Fsp95405
    Hi Jean, thank you for your question. Yes, it looks like your old part number updates to this part so it should work. I hope that helps. Good luck with your repair.

    Was this helpful?
    Thank you for voting!
      Model Cross Reference
      This part works with the following models:
      PartSelect Number: PS11746889
      Manufacturer Part Number: WP95405
      Brand
      Model Number
      Description
      Kenmore
      110357116
      Washer
      Kenmore
      110357972
      Washer
      Kenmore
      110358365
      Washer
      Kenmore
      110358371
      Washer
      Kenmore
      110358484
      Washer
      Kenmore
      110358487
      Washer
      Kenmore
      110358488
      Washer
      Kenmore
      110358507
      Washer
      Kenmore
      110358519
      Washer
      Kenmore
      110358794
      Washer
      Kenmore
      110358795
      Washer
      Kenmore
      110359054
      Washer
      Kenmore
      110359055
      Washer
      Kenmore
      110362101
      Washer
      Kenmore
      110364443
      Washer
      Kenmore
      110365012
      Washer
      Kenmore
      110365359
      Washer
      Kenmore
      110365859
      Washer
      Kenmore
      110365948
      Washer
      Kenmore
      110366559
      Washer
      Kenmore
      110366660
      Washer
      Kenmore
      110395055
      Washer
      Kenmore
      1106004711
      Washer
      Kenmore
      1106004761
      Washer
      Kenmore
      1106005711
      Washer
      Kenmore
      1106005761
      Washer
      Kenmore
      1106114231
      Washer
      Kenmore
      1106114241
      Washer
      Kenmore
      1106114251
      Washer
      Kenmore
      1106114800
      Washer

      Get in touch, we're here to help!

      Open until 10PM EST

      Contact Customer Service