Door Gasket WP902894

ordered new gasket, watched the video that was in the order conformation on how to install which was very easy to understand. the actual installation was right on the money. Thank-you.

The repair was very easy! I simply pulled out the old gasket from around the front part of the dishwasher. I cleaned the area with a damp rag from any residue that was left on. I bent the long gasket in half and and pushed it in starting at the center of the dishwasher and went down one side at a time until the whole gasket was in. I then ran a short cycle on the dishwasher to make sure it was properly in place and the problem was fixed. NO MORE WATER ON THE FLOOR! I was so very happy to know my problem was fixed and I didn't need to buy a new dishwasher! It's been running great! :) ~ Elizabeth ~

Pride old gasket out with screw driver easily removed it cleaned where the gasket was with mild detergent and easily installed new gasket

I removed the gasket from around the dishwasher. Cleans the grove of any dirt, mold or other debris. I started the gasket replacement at the top center of dishwasher by folding the gasket in half to find the center and inserting that center point into the grove just below the latch.i then inserted the rest of gasket with my thumb into the remaking grove first to the right corner then to the left. No told were needed leak was gone

Pulled out old gasket with pliers. Pushed the new one in place by hand. Note: the replacement gasket was slightly narrower and also a good 3 inches shorter! I compensated for the length by leaving in a 3 inch section of old gasket in the middle where I knew there was no leaking and cut the new one into two pieces on either side. The narrower width was a problem because it could not hold itself in place by friction as it was supposed to. Instead I used spray mount adhesive on the backside to help it stay put. Hope it continues to hold. I wish the product description was more precise to help me determine whether this product would work or not. The photos were not sufficient to tell.

Used a piece of tubing and jammed it in until the part came and that worked. Got the gaskets, took out the old one, in with the new ... and cut a wee bit off the end and presto done ... could be my imagination but it seems a tad quieter now as well. Naturally the soap dispenser door took a powder now, so I'm waiting for those pieces (Couldn't find them in the tub, but did manage to slice a finger open on a piece of glass while feeling around for them!) ...

Thanks for the instructions. It helped. However, there should be more attention spent with the seal at each end. On one side it is evident that the seal should be flush to the bottom of the door. However, the right side seems to indicate that the excess seal should be left hanging out. That is what I did the previous time I replaced the seal. Soon it started leaking. This time I made both sides of the seal flush with the bottom of the door. Also the first time I installed the seal, it was too short. I had to reset and slightly pull the seal to increase length.

I read your website and followed the GREAT directions that others provided. Repair complete! Dishwasher working and not leaking!

After dissassembling the unit to discover the leakage source I determined that it would do best to replace the top three contributors to the problem as listed by you. Disassembly, parts replacement and reassembly was straight forward and a few hints garnered from your good instructions and assembly blow-up drawings made the job simple with the most difficult task being the removal of the adhesive foam gasket at the bottom of the door's interior. After scraping as much of the deteriorated foam away as possible with a plastic scraper I used some of my wife's nail polisher remover and a clean-up rag (being careful not to get the remover on plastic parts)and soon I had the adhesion area surface clean and ready to receive the new seal. With close attention to clean up of residues left behind from detergent and water and care taken with part installation and reassembly it no longer leaks and I hope to get another 10-15 years of leak free operation out of the dishwasher

Pulled out the old gasket and pressed in the new one. No more leakage.