This authentic OEM high limit thermostat is made for your dryer. It is an important dyer element, because it will automatically shut off the heating element when it overheats. Be sure to disconnect the power to your dryer before you begin this repair.
How Buying OEM Parts Can Save You Time and Money
Troubleshooting
This part fixes the following symptoms:
Too hot
This part works with the following products:
Dryer.
This part works with the following products:
Whirlpool, Maytag, Kenmore, Amana.
Part# WP8557403 replaces these:
AP6013164, 8557403
Customer Reviews
Average Rating:
★★★★★
★★★★★
2 Reviews
5.0
Filter By Rating:
5 Stars
2
4 Stars
0
3 Stars
0
2 Stars
0
1 Star
0
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
George B - February 12, 2020
Verified Purchase
Easy repair, went as expected.
Part was here when expected and was exactly same as original,
★★★★★
★★★★★
Donald G - April 18, 2019
Verified Purchase
Part fit and worked good
The part was correct and arrived fast. Will order from them again if need be
< Prev
1
Next >
Customer Repair Stories
Average Repair Rating: 3.2 / 5.0, 3 reviews.
What's this?
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Dryer wasn't heating.
Replaced high limit thermostat and thermal cutoff. Dryer works like a champ. Reviewed couple of YouTube videos that showed clearly how to get to the effected parts, test them and replace them. I had an old front loading dryer once before that I repaired a couple of times but these parts were accessible by removing a panel on the
... Read morerear of the unit. The procedure was more involved with this unit. After studying the videos and getting a feel for what was involved, the process, while involved, was fairly simple and putting the unit back together was also fairly easy. Replacement parts did the trick. Very happy.
We have a very early model of the He3. We had to follow directions for the He2 model to replace the heater element and thermostat. Access is easy through the front panel, but removing and replacing the element required some force and maneuvering in a small area.
We replaced both the element and the thermostat since we had the
... Read moreentire part disconnected and removed. So far working great!
Remove backing very easy (approximately 12 8mm screws). Thermostat on left side facing the back. 2 8mm screws . Thermal fuse slightly further towards front of dryer but still accessible (caution longer arms needed). Unscrew first them release safety clamps to unplug (be gentle have patience). Place all back same as removed an
... Read mored it worked!!
Ask our experts a question about this part and we'll get back to you as soon as possible!
8 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Dianna
November 16, 2017
Is replacing the thermostat a homeowner can easily do?
For model number WED8200YW0
Hi Dianna,
Thank you for your inquiry. Replacing the thermostat is fairly easy to do. There is a video on our website that you can reference on how to install the thermostat. You will find the video under part number PS11742185. I hope this helps. Thank you and have a great day!
4 people found this helpful.
Was this helpful?
Thank you for voting!
Gerald
September 16, 2019
How do i test this part to ensure it has failed
For model number YWED80HEBW0
Hello Gerald, thank you for your question. Testing a thermostat is easy! Set your multimeter to the R X 1 setting. Take each of your meter's probes and touch one to each terminal. You are testing for continuity, and you should receive a reading of either zero or infinity. At room temperature, testing the thermostat should produce a reading of zero. But if a thermostat is tested when it is heated to its limit, a reading of infinity should be produced. We strongly recommend that you test your thermostat at room temperature. If the test you conduct with your thermostat does not produce these results, then you should replace the component. I hope this helps!
4 people found this helpful.
Was this helpful?
Thank you for voting!
Elisa
March 3, 2020
Is this thermostat the same as the one that comes with the thermal cut off?
For model number WED9200SQ1
Hello Elisa, Thank you for the question. Yes, this sit he Thermostat that is included in the Thermal Cut-Off with High Limit Thermostat, PartSelect Number PS991443. We recommend replacing both parts in the kit at the same time. We hope this helps.
How do you test this part as it has 2 large and 2 small terminals. What are normal or abnormal results?
For model number wed9400sw
Hello James, Thank you for contacting us. Test each set of terminals. With your multi-meter on the Rx1 setting, you should receive a reading of zero or infinity. Hope this helps.
Was this helpful?
Thank you for voting!
Raul
February 8, 2022
I've checked this and I believe the other one is the heat cut off and both have perfect continuity. My dryer turns on sometimes but won't start the times it does turn on. Any idea what that might be? Thanks
For model number WED8000DW4
Hello Raul, Thank you for the question. We suggest testing the Door Switch to check the continuity. Make sure it is secure as well so when the door is closed the switch is getting activated and tells the controls the door is closed. If you need help placing an order, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you!
My heating element has 3 prongs on it with two purple wires and a red jumper wire I bought an additional element and can only find them with 2 prongs is there a way to hook the 2 prong element up
For model number Med5100dwo
Hi Joseph, thank you for reaching out. We have found that the compatible heating element for your model is part number PS11746338, and it only comes with three terminals. We hope this information helps!
My dryer quit working so i went to your sight it recommened replacing the thermal fuse i did it ran one load the body of the dryer was very hot to the touch and wouldn't start i bought another fuse and thermostat internal bias it ran another load with the same results what should i check for now?
For model number 11087872603
Hello Hubert, thank you for inquiring. You will want to check the Door Catch, part number PS334230, and the Moisture Sensor, part number PS11741408 for your model. Good luck with your repair!
Was this helpful?
Thank you for voting!
Chad
February 9, 2018
On my dryer, 1 of the 2 wires that plug into my heating element keeps melting at the connection. What would cause this to happen? I checked the continuity of the element and it is good. I have replaced the thermostat and the thermal fuse. The thermal fuse blew after drying one load. Not sure what to check next and why the wire is melting at the connection.
For model number Wed9500tw2
Hi Chad, Thank you for the question. I suggest checking the exhaust pipes and lint ducks to make sure they are not blocked. Lint and moisture can block them over time and cause over heating of the element. Hope this helps!
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
