Not cleaning dishes properly | Noisy | Not draining
This part works with the following products:
Dishwasher.
This part works with the following products:
Whirlpool, Kenmore, KitchenAid, Amana.
Part# WP8268342 replaces these:
AP6012230, 8268342
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
9 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
MIKE
August 25, 2017
How does lower spray arm attach to support hub?
For model number DU1100XTPQ1
Hi Mike,
Thank you for your question. The spray arm actually just screws on and off of the support. You have to hold the support in place and then slip your spray arm over it and screw it on. I hope that helps. Good luck with your repair.
4 people found this helpful.
Was this helpful?
Thank you for voting!
DW
February 27, 2018
The lower wash spray arm while spinng on"support hub" hits the manifold resulting in a racket. Q. By replaceing support hub eliminate the hitting of spray arm ? Part #8268342
For model number KUDI01ILB5
Hello DW, thank you for your question. Yes, replacing Lower Spray Arm Support/Hub should fix the issue. I would also recommend replacing the Rear Feed Cap part number WP8268343 and Spray Arm Seal WP8268340. Good luck with your repair!
2 people found this helpful.
Was this helpful?
Thank you for voting!
Norma
April 26, 2018
I can't get the screw to come off from the top of the lower water blade assembly. I have tried everything , cna you help me?
Hi Norma,
Thank you for your question. We do have an installation video for this part: https://youtu.be/ZFr2Ezbs-ac . You may have to hold down the spray arm as you are trying to unscrew the nut. Sometimes the nut is a left hand direction to unscrew. I hope that helps. Good luck with your repair.
2 people found this helpful.
Was this helpful?
Thank you for voting!
Tomas
May 10, 2019
I have this part damaged (the thread is damaged) and i was wondering if this part could cause the leaking water from the bottom???
For model number DU1300XTVS2
Hi Tomas, thank you for your question. This part could cause leaking but the parts that I would suggest you check if you are getting leaking from underneath of your dishwasher would be the water inlet valve and your hoses that attach to the appliance. I hope that helps. Good luck with your repair.
Was this helpful?
Thank you for voting!
John
August 26, 2019
Hi i need a KitchenAid kudc 20cvss2 spray arm fastener. Which one should i buy from you?
For model number kudc20cvss2
Hi John, thank you for your question. I have linked that part below for you. Good luck with your repair.
How do I remove the lower arm to clean the strainer? Thanks
For model number KUDP02CRBL1
Hi Mike,
Thank you for your question. There is a video listed with the part on our website that you may reference on how to remove/install the part. Here is a link to the part, so you may view the video, https://www.partselect.com/PS11752756-Whirlpool-WPW10320510-Lower-Spray-Arm.htm?SourceCode=4&SearchTerm=KUDP02CRBL1&ModelNum=KUDP02CRBL1. I hope this helps. Thank you and have a great day!
Was this helpful?
Thank you for voting!
Lise
January 21, 2023
I am looking at the Part Number PS 11745437/Maufacturer Part Number WP8268342.
Will it fit my Kenmore Mod as described above. I screwed in the plastic screw and cannot remove it. I still can't figure out how to remove the plastic screw ? It is stripped..and it won't unscrew.
For model number Kenmore Mod. 665.16293402
Hello Lise, thank you for reaching out. Yes, this part will fit your model. You may have to hold the spray arm down while removing the nut. Sometimes it can get stuck. However, you should be able to remove it just by unscrewing the support hub here. We have researched your model and attached a relevant video that might help you with your problem. We hope this helps, good luck with this repair.
Was this helpful?
Thank you for voting!
DW
March 3, 2018
My Kitchenaid dishwasher fills up for the first cycle, then starts and a loud racket noise begins and continues through the following cycles. I ruled out the spinning spray arm on the "support hub" - any clue to the problem?
Hello DW,
Thanks for your question. You may want to test the circulation pump and motor with a multimeter to check for electrical continuity. Replace it if it shows no continuity. Consider examining the chopper assembly and door balance kit for any signs of wear and tear as well.
I hope this helps.
I am having trouble unscrewing the plastic tab on the lower spray arm it screws up but will not come completely out to allow the arm to come off. Any advice would help
For model number KUDP01ILWH6
Hi Greg,
Thank you for your question. You may have to hold the spray arm down while removing the nut. Sometimes it can get a little stuck. However you should be able to remove it just by unscrewing the support hub here. I am not sure what would be stopping it from pulling out all the way. I hope this helps. Good luck with your repair.
Was this helpful?
Thank you for voting!
< Prev
1
Next >
Part Videos
Replacing your Whirlpool Dishwasher Lower Spray Arm Support/Hub
Customer Repair Stories
Average Repair Rating: 2.9 / 5.0, 4 reviews.
What's this?
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Noisey motor
just followed what I took out and replaced washing unit
Richard from CHELMSFORD, MA
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers
1 personfound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken plug
The instruction video absolutely helped me. I was really pleased that I received a frig magnet because I will use this company for all my DIY PARTS
machine has been extremely noisy for over 6 months, then quiet running altogether.
Double checked the model number , watched the video, ordered the parts . I got them in about three days , They looked exactly like the old ones. Proceeded with the disassembly just like the video explained and everything was going great.until I got to the installation part. The new unit would not fit in the sump. even though it looked exactly the same size as the old one. I worked with it every way I could, lubricating it and applying light pressure and finally beating the fire out of with a hammer and it just would not seat in the bottom of the sump. I removed it and reinstalled the old one and fit right in. So I removed all the parts out of the new unit and installed them in the old housing. From that point on the installation went well and now the dishwasher is as quiet as a mouse and so is my wife now. I did not have anything to measure the diameter of the unit accurately but eyeballing it with a rule it looked to be maybe a n 1/8" larger. So it appears to have been a tolerance problem. Not happy about that but I was able to get dishwasher going and the video was great help .
removed parts and the ordered the parts. It was very easy to order parts from Partselect. I unscrewed a few screws and the disassembly was a breeze. I then revresed my steps and the new parts were instlalled no problem. Now on the the motor replacement. Thanks Partselect.com
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Sandra H - April 30, 2021
Verified Purchase
Dishwasher up and running
Part arrived sooner than expected, easy to install
★★★★★
★★★★★
Michelle B - May 16, 2020
Verified Purchase
Easy installation
Dishwasher would not dissolve detergent. Took apart bottom and cleaned area and noticed the lower spray arm support was broken. Replaced and dishwasher now working properly.
★★★★★
★★★★★
Gerald T - April 18, 2018
Verified Purchase
Worked.
The part arrived very quickly and all is well now.
