Quick Question!

Have you ever purchased from PartSelect.com before?

11745016-1-S-Whirlpool-WP8182634-Door Lock Latch
11745016-1-S-Whirlpool-WP8182634-Door Lock Latch 11745016-2-S-Whirlpool-WP8182634-Door Lock Latch 11745016-3-S-Whirlpool-WP8182634-Door Lock Latch https://www.partselect.com/Schematics/Maytag/58654.gif

Door Lock Latch

Your Price

$77.23
Get this part fast. Average delivery time via standard shipping: 1.8 days.

PartSelect Number PS11745016
Manufacturer Part Number WP8182634
Manufactured by Whirlpool

This part is used on front load washers and includes the interlock switch assembly.

This part works with the following brands: Kenmore, Whirlpool, Maytag, KitchenAid, Amana, Inglis.

This part works with the following products: Washer.

This part fixes the following symptoms:

  • Lid or door won’t close.
  • Will Not Start.
  • Lid or door will not open.
  • Will not fill with water.

Videos For installing this part.

Questions & Answers

Ask our experts a question on this part and we'll respond as soon as we can.

Most Helpful

Question:

My washer was running through a cycle during a storm and the power went on and off a few times. The washer cut off and will not power back on. I checked the breaker and the outlet and both are working. The clothes were locked in so I watched a video how to release the door mechanism and got the clothes out. I called a local repair company and the tech came out and didn't do anything but plug it in and checked the breaker. He then said its either the do locking mechanism or the main control board and he would call me back with a price for both. Shouldn't there be a way to diagnose which it is so I don't have to pay for both and only hope one works?

Dave for model number MAH6700AWW
Answer:

Hi Dave, Thank you for the question. If there is no lights coming on and it is not powering on at all then It would more then likely be the control board. Usually with the door lock the lights on the control board will still come on but you would get a error or the door would not open but it would still power on. Hope this helps!

2 people found this helpful.
Question:

Hello.... i have a Whirlpool front load washer... the machine lights up and you can change or make any selections on the panel but when i push start nothing happens other than the light on the selector knob flashes.... the door does latch closed but normally when i hit start i hear it lock... do you feel that it could be a bad door lock or main computer? thanks for your impute.

David for model number GHW9100LW
Answer:

Hi David, Thank you for your inquiry. Where your washer is not starting the part that fixes the issue the majority of the time is the door lock latch. I hope this helps. Thank you and have a great day!

2 people found this helpful.
Question:

Will this part help latch the door? I recently bought the door latch because it was broke but now the door won't latch to close to secure it.

Shelly for model number NFW7200TW10
Answer:

Hi Shelley. This part (PS11745016) allows your washer to lock, and I have double checked our system and it will fit the model number you have provided (NFW7200TW10). Thanks for your question, and good luck with your repair.

1 person found this helpful.

Most Recent

Question:

Code FL pops up which I know means failed to lock so will getting the latch help or is another part I need?

Byanca for model number MAH8700AWW
Answer:

Hi Byanca, Thank you for the question. Yes we suggest replacing the Door Lock Latch to fix the FL error code. Good luck with the repair!

Question:

When i press the start button on my washer, i hear a loud click noise and then the breaker trips. This does not happen every time. Will replacing the door lock latch address this issue. Also, there are times where i need to reopen the door and close it again before the machine will start.

John for model number GHW9100LW1
Answer:

Hi John, Thank you for your inquiry. If the washer is tripping the breaker there could be a wire shorting out somewhere, water getting into an electrical part, it could be the motor, the circuit breaker itself or a number of other issues. You may have to have a technician come in and verify what is going on. I hope this helps. Thank you and have a great day!

Question:

I have a Maytag front loading washer model number mfw9600sq0. I just replaced the door latch, but it didn't fix my issue. The water runs into the washer, however it never spins, it just sits there quietly until it's time to drain, which it does fine. It's like my whole spin cycle is missing. Occasionally i will also get a short quick buzz noise. Any other ideas on how to trouble shoot this? Thanks

Holly for model number MFW9600SQ0
Answer:

Hi Holly, Thank you for the question. Sounds like the timer that sends the appliance into the cycles is defective. When the timer is defective it can skip one or more cycles or not advance at all. The timer for your model is built into the Electric Control Board. Hope this helps!

Related Parts: Control

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.0 / 5.0, 22 reviews What's this?
1-15 of 22
 

169 of 191 people found this instruction helpful

Parts Used:
  • Door Lock Latch
Level of Difficulty: A Bit Difficult
Time to do repair: Less than 15 mins
Tools: Nutdriver, Screw drivers
Customer: James from Vilonia, AR

Front load washer latch replacement

1. remove the three screws from the top backside of the top panel
2. push the top panel to the rear 1/8 to 1/4 inch
3. lift/rotate top panel from rear to front, set aside.
4. remove the three wire connectors from latch.
5. use #15 Torx to remove the three screws from the latch.
6. remove and replace part using top opening.
7. reverse order to finish.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

56 of 58 people found this instruction helpful

Parts Used:
  • Door Lock Latch
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: Suryakant from Cortlandt Manor, NY

Door lock was in the locked position and door could not close

I bought a new door lock for 132 dollars (item number PS2037196).

Ultimately you have to get to the inside of the machine where the door lock is located in order to see if you will need this door lock that I bought.

DISCONNECT POWER FROM MACHINE.

First take off the top by taking off the 2 screws on the back of the machine.

Second take off the control panel, I believe there are about 5 or 6 screws for that.
(there's also a screw when you open up the detergent compartment on the bottom left- also, a lever must be pushed in order for the compartment to come off- it MUST be taken off).

Third unscrew the top of the front white plate.. there should be a 5 or 6 screws for that.
You don't need to take off the entire front plate.

Finally unscrew 3 screws that hold the door lock in place .. make sure your hands is in the machine- the back of door lock to catch the lock when you're on the last screw.

Gently take out the door lock from the side with the cables attached by holding the white metal door open (it bends).

Try to pull on the bottom of the door lock (its a manual release). If it doesn't release you need to buy a new door lock like I did... if it does release then you don't need a door lock and just reassemble.
(Note: You can also try plugging in the machine and THEN pulling down on the manual release. When I tried this the door lock just vibrated and nothing happened so I bought a new door lock.)

If you have the new door lock continue here:

Take out all 3 cables on the old door lock by pressing on the corresponding clips.

Attach the new door lock with the correct cables. Assemble machine back together.

Thats it.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

30 of 36 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: 30 - 60 mins
Tools: Pliers, Screw drivers, Wrench (Adjustable)
Customer: Jason from Frost, TX

Quarter was in the water pump

The repair was very simple I also broke the door latch when this happen as well to get the water out of the drum. Both components were very simple to replace and took less than a hour. My order was deliver very promply even a day earlier than I expected. Everything was correct and the price was well below any price I could find in town or on any other web site. I hope I never need anything else for this equipment but if I do this will be my first choice for the parts purchase. Thanks, Jason Frost,Texas

Help other customers find the most helpful instructions.

Were these instructions helpful?   

29 of 37 people found this instruction helpful

Parts Used:
  • Door Lock Latch
Level of Difficulty: A Bit Difficult
Time to do repair: 1- 2 hours
Tools: Nutdriver, Screw drivers
Customer: Glenn from Las Vegaas, NM

The washer became unbalanced and broke the latch on door

Had to take the entire front of the washer off to replace the door latch.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

21 of 25 people found this instruction helpful

Parts Used:
  • Door Lock Latch
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: Tina from petersburg, VA

Door would not lock

Peel rubber gasket from drum; remove 3 screws using phillip head screwdriver; disconnect wiring e plugs; remove door lock. Install in reverse order.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

16 of 31 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: Brenda from Bodega Bay, CA

Door hangs down so you have to lift it when closing. Eventually the whole latch mechanism broke.

Pull washer away from wall and find two screws in back next to top edge. Undo and pull top of machine off (lip on fron edge under face cover). reach down and unplug three plugs on door latch small one on top, biggest on bottom. Unscrew the three screw holding the latch on the front of the machine, take out the old and put in the new. Note, I pluged in the plugs before screwing the new one in place, and that might be easier. Put the top back on.
I couldn't find any way to adjust the door, so you still have to lift it up when closing.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

10 of 14 people found this instruction helpful

Parts Used:
  • Door Lock Latch
Level of Difficulty: Easy
Time to do repair: 30 - 60 mins
Tools: Nutdriver, Screw drivers, Socket set
Customer: Alexander from Miami, FL

Broken lock needed replacement

The best way to do it is not the way I started.
The best way is to 1st remove the bellow's front clamp with a small screwdriver at the spring. 2. unplug the 3 sets of wires attached to the lock. 3. remove the 3 screws on the front that hold the lock. 4. remove the plastic ribbon harness that attaches to the lock. 5. remove the old lock. 6. install the lock back carefully moving aside the cables. 7. install the 3 screws. 8. attach the ribbon harness. 9. attach the cables. 10. replace the bellow. 10. replace the clamp (here you may need someone's help to keep the rubber in place.) 11. the last part to fall in place is where the spring is. 12. If you can't do all by tact then you may want to remove the 3 screws from the top cover to be able to c where all fits.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

7 of 9 people found this instruction helpful

Parts Used:
  • Door Lock Latch
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: MICHAEL from DERIDDER, LA

The washer was unable to run without door locking

Removed the washer tub gasket and then removed the door part that I order . It was real easy to replace it and the tub gasket . Took about 8 min to complete everything .

Help other customers find the most helpful instructions.

Were these instructions helpful?   

9 of 15 people found this instruction helpful

Parts Used:
Level of Difficulty: A Bit Difficult
Time to do repair: 1- 2 hours
Tools: Nutdriver, Pliers, Screw drivers
Customer: MIKE from LONGWOOD, FL

Door would not open.

It takes 2 people to do this repair.The bellow is the hardest part. One person has to hold the bellow in one spot, and the other person has to put it on the rim of the drum all the way around. Sort of like putting a tire on a bicycle. Dont do what I did and pry the door open. If you do that you will have to get a new door lock control at $54.Take off the lower front panel and reach up to the manual releace tab on the right side and pull down. Please make sure that the power is turned off, unplug the washer from the wall for your safety. The door switch itself is easy to replace, 3 screws, 3 plugs. Hope this helps.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

9 of 16 people found this instruction helpful

Parts Used:
  • Door Lock Latch
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: Gary from Sonoma, CA

Door latch error code

removed all the panels to change the door latch switch
plug in three plugs ...works great
Thank you

Help other customers find the most helpful instructions.

Were these instructions helpful?   

5 of 6 people found this instruction helpful

Parts Used:
  • Door Lock Latch
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Nutdriver, Screw drivers
Customer: gerard from arvada, CO

Following the instructions of the repair manuel,

First I removed the retainer ring and then pulled back enough of the boot to get the door switch out and plugged in the new switch put the retainer ring back on and it was finished. With out the repair book I would have been lost on how to do the job.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

5 of 7 people found this instruction helpful

Parts Used:
  • Door Lock Latch
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver
Customer: David from Post Falls, ID

Door latch failed and would not lock

Took off bottom panel by removing 3 torx screws. Opened up door seal, removed three latch retaining screws, unplugged three wiring harnesses. Installed new latch and reinstalled in reverse order.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

4 of 5 people found this instruction helpful

Parts Used:
  • Door Lock Latch
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver, Screw drivers
Customer: William from Victorville, CA

Door latch would not lock

Removed 2 screws from rear of top that hold top of washer in place, lifted top at the rear and slid it back then lifted it off. Removed the three wiring harnesses from old switch, removed the three screws holding switch in place, theses are accessed from the door opening. removed the two lower screws first and held the switch from the top while removing the last screw. Placed new switch in place and started the top screw by hand followed by hand starting the remaining two screws, tightened screws with phillips screw driver, reconnected the three harnesses, reinstalled the top and secured with the two screws. Door locks and unlocks as it is supposed to.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

4 of 5 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: larry from Pleasant Garden, NC

Broke door latch and handle

very easy fix. works great and good price on parts

Help other customers find the most helpful instructions.

Were these instructions helpful?   

5 of 9 people found this instruction helpful

Parts Used:
  • Door Lock Latch
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: FRANCIS from leesburg, FL

Door would not latch , and lights on front just flashed

1)I removed the bottom front panel,reached up the right side of the machine and pulled the manual release on the bottom of the latching mechanism.2)I then removed the top to the machine in order to gain access to the latch. 3)I removed three electrical connectors then the three mounting screws using a #15 Torx driver. I then reversed the reverse procedure to install the new latch. total time to do the job was less than half an hour. Machine works OK.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1-15 of 22

Model Cross Reference

This part works with the following models:

PartSelect Number: PS11745016
Manufacturer Part Number: WP8182634
Brand Model Number Description
Kenmore11042822200Washer
Kenmore11042822201Washer
Kenmore11042822202Washer
Kenmore11042822203Washer
Kenmore11042824200Washer
Kenmore11042824201Washer
Kenmore11042824202Washer
Kenmore11042824203Washer
Kenmore11042826200Washer
Kenmore11042826201Washer
Kenmore11042832200Washer
Kenmore11042832201Washer - Kenmore Washing Machine
Kenmore11042834200Washer
Kenmore11042834201Washer
Kenmore11042836200Washer
Kenmore11042836201Washer
Kenmore11042922200Washer
Kenmore11042922201Washer
Kenmore11042922202Washer
Kenmore11042922203Washer
Kenmore11042924200Washer - Kenmore Washing Machine
Kenmore11042924201Washer
Kenmore11042924202Washer
Kenmore11042924203Washer
Kenmore11042926200Washer
Kenmore11042926201Washer
Kenmore11042926202Washer
Kenmore11042926203Washer
Kenmore11042932200Washer
Kenmore11042934200Washer