The dishwasher lid spring helps open the dispenser cover in the soap box when the control releases the latch. If your dishwasher does not dispense detergent, is broken and worn out, or the door is not opening properly, replacing the dispenser spring could be the solution. For this replacement you will need needle nose pliers. First, release the cover on the detergent dispenser, then remove the cover from the shaft it hinges on. Pull the shaft from one side and remove the spring from the shaft. Next, replace with the new spring and engage the two open hooks into the soap cover. Finally, grasp the hook and pull it over tab on the side of the wash cup. Verify that it works properly by opening and closing the cap. Refer to the manual provided by the manufacturer for further instructions.
How Buying OEM Parts Can Save You Time and Money
Part Videos
Replacing your Whirlpool Dishwasher Spring, Lid
Troubleshooting
This part fixes the following symptoms:
Will not dispense detergent | Door latch failure | Not cleaning dishes properly | Door won’t close
This part works with the following products:
Dishwasher.
Part# WP8066018 replaces these:
AP6011676, 300106, 8066018, 99989653
Customer Reviews
Average Rating:
★★★★★
★★★★★
12 Reviews
4.3
Filter By Rating:
5 Stars
10
4 Stars
0
3 Stars
0
2 Stars
0
1 Star
2
Sort by:
< Prev
1
2
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
MG K - October 8, 2022
Verified Purchase
Would not owrk
I don't understand why but I cannot position the spring such that it maintains it's pressure (spring) such that the door will spring open. Every time I lift the spring over the catch the spring loses it's grip in order to stretch the spring! I cannot get it to maintain the pressure needed to open the door. Any suggestions?
★★★★★
★★★★★
Lana G - August 17, 2022
Verified Purchase
Easy repair
Exactly what we needed to fix our dishwasher.
★★★★★
★★★★★
Martha Z - January 6, 2021
Verified Purchase
Easy repair
The part was in great condition and arrived on time. Never could I have thought that I could fix my dishwasher on my own.
★★★★★
★★★★★
Jason C - January 5, 2021
Verified Purchase
Great part
Easy and fast to repair and now the detergent drawer works.
★★★★★
★★★★★
Joshua M - June 30, 2020
Verified Purchase
Easy repair
Part was correct. Easy to install. Works perfectly.
★★★★★
★★★★★
Janis S - April 24, 2020
Verified Purchase
Replacement spring for dishwasher soap dispenser lid
It was not easy to install. I ordered 2 and bent one up trying to get it in right. A great spring!
★★★★★
★★★★★
Richard S - December 23, 2019
Verified Purchase
Simple repair
I really appreciated the short video showing how to install the part, big help
★★★★★
★★★★★
Robin C - September 7, 2019
Verified Purchase
Easy repair. Video helped a lot@
Spring lid was easy to insert with peg.
★★★★★
★★★★★
RALPH C - February 7, 2019
Verified Purchase
Dishwasher parts
We are very happy with partseelect.
Price was reasonable, delivery was fast and instructions was great
★★★★★
★★★★★
Nathan R - August 9, 2018
Verified Purchase
Weak spring
The spring is weak and flimsy. Had to reuse orginal spring.
< Prev
1
2
Next >
Customer Repair Stories
Average Repair Rating: 4.0 / 5.0, 12 reviews.
What's this?
Sort by:
< Prev
1
2
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
No water to the upper rack, soap dish not opening properly
Replaced the middle spray arm kit and the upper spray arm mount. Also replaced worn out spring for the soap dish. Now all areas of the dishwasher get cleaned and the soap dispenses correctly every time.
I looked online to see a video. Dad to pop lid off soap dispenser. Slide a plastic part to the left n the spring slide off. Video showed how to place prongs on spring . Then had to lift the upper part of spring to lift onto plastic part of soap dispenser. That was it.
Unfortunately it still doesn't work. I asked Ina email to yo
... Read moreur company for any suggestions, No reply.
Read less
Anthony from CLEVELAND, OH
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
1 personfound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The spring on the detergenet dispenser box door failed and needed replaced
The old spring on the detergent dispenser box door failed and the dispenser door would not pop open at the right time in the wash cycle.
Ordering the new spring was easy on the website. Need dishwasher model number, stock number and serial number.
Hint - Order at least 2 springs! They are not expensive.
... Read more>I followed the instructions in the video. I could get the spring on the spindle correctly but could not get the two spring prongs to catch to create spring tension on the door without using a thin knife blade to carefully push each prong to where it caught on the dispenser door.
I needed to slide the prongs slowly and carefully to get them to catch on the door. This distorted the spring. That's why you really need two springs. I then used needle nose pliers to pull the latching part of the spring to catch on the inner door. That distorts the spring, too.
So you really need two springs. One spring to learn how to do it and a second one to replace the one you distorted as you learned.
Take care
Read less
John from WESTERVILLE, OH
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Pliers
3 of 3 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
SOAP DISPENSER DOOR DID NOT CLOSE.
WATCHED THE VIDEO FOR 2 MINUTES. REPLACED THE 3 PARTS IN LESS THAN A MINUTE. THANKS FOR THE VIDEOS.
First, examine very carefully how the old spring relates to the detergent release box lid. Note that the top of the spring has a square-end upside down "U" . This rests on a small ledge on the detergent box. Also note that on either end of the spring is a straight extension of the spring wire. These two "legs" must rest on the inside o
... Read moref the edge of the detergent box. Second, use a flat blade screw driver to pry the LID hinge pin from the mounting "posts. Remove the pin, first noting the position of the spring. Reassemble the spring on the hinge pin in reverse order. Then snap the lid onto the spring using the two mounting "posts". NOTE: I used a very fine needle nose pliers to move the two spring "legs" behind the detergent box edge after I had mounted the lid. Flip the lid down to test if the spring pressure on the lid can be felt. Harold Kitzmann, Fishersville VA
Replacing the pin with the spring is a little tricky, it was hard to hold it. And the little plastic pin breaks real easy too, its hard to get the lid to snap in place without breaking the pin.
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
2 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Ling
January 22, 2023
The soap dispenser sometimes has soap left after washing and dishes are not clean. A few times the door of dispenser is not open. Which parts should I replace? Thanks!
For model number 63013003016
Hello Ling, Thank you for your inquiry. If the dispenser is not opening and releasing the soap, then check the parts of the dispenser such as the seal, the spring and the lid. The seal is only available as part of the complete dispenser assembly. It could also be caused by the water not being hot enough so we would recommend checking the water circulation pump with heater and make sure that the water going into the dishwasher is hot. You can test the pump with a multimeter. If you are unfamiliar with how a multimeter functions, we have videos available to assist you. We hope this helps.
Soap dispenser doesn’t open during cycle
But when I manually turn the knob through each cycle it opens.
For model number DU810SWPU3
Hi Alvin, thank you for contacting us. The issue probably seems to be with the dispenser actuator assembly, part number PS392727. It opens the dispenser cover to release detergent and rinse aid during the dishwashing cycle. If you require assistance to place an order, please contact customer service!
Item is in stock and will ship today if your order is placed before 4:00 PM Eastern Standard Time.
If your order is placed after 4:00 PM EST, the in stock items will ship on the next business day.
On Order
Item is not in stock and usually ships 3-5 business days from the time you place your order.
Special Order
Item is not in stock and usually ships 10-15 business days from the time you place your order.
NLA - No Longer Available
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.
[{"position":0,"name":"Home","title":"Home","url":"/"},{"position":1,"name":"Dishwasher","title":"Dishwasher","url":"/Dishwasher-Parts.htm"},{"position":2,"name":"Spring or Shock Absorber","title":"Spring or Shock Absorber","url":"/Dishwasher-Springs-and-Shock-Absorbers.htm"},{"position":3,"name":"WP8066018","title":"WP8066018","url":""}]
You added 1 item to your cart
✖
$
Qty:
Total item(s) in cart:
Order Subtotal
$
*Taxes and shipping will be applied during checkout
