Average Repair Rating: 4.1 / 5.0, 3 reviews.
What's this?
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Clothes would not fully dry in automatic cycle
1st gen whirlpool Duet dryer sensor not working in automatic cycle. After ordering the moisture sensor harness which is about 6-8 inches long, I removed the lower panel and it is right there. I disconnected the two wire connectors in the upper left and I need a small screwdriver to disconnect the two pin connector which was a bit of
... Read morea pain but once replaced I no longer had to use the timed setting to dry clothes and this will save me electricity.
Read less
Robert from WALDORF, MD
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
1 personfound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Both hinges were bent, probably from dropping the door, or leaning on it when it was in the down position.
1st; I opened the door, 2nd; removed the keepers that prevent the door from coming unhinged. 3rd; placed 2 short screws in the holes in the hinges. 4th; raised the door until it stopped. 5th; lifted the door upward and slid the hinges out of the slots in the range. 6th; laid the door face up on a microwave stand. With a handle on the outs
... Read moreide, and hinges sticking out of the inside, it was inpossible to lay the door flat on a larger surface, and get around it. 7th; removed 2 screws from the inside top, and the 8 screws from the very bottom. 8th; removed the bottom rail, and the handle assembly. From there everything was stacked pieces. Picked the glass front up, and carefully set it safely aside. Picked each piece up and cleaned it, and started the re-assembly. The hardest part of the process was getting the fiberglass rope around the inside glass, to stay in place during the initial re-assembly. From there, the assembly was just the reverse order. the process was about 1 hour and 20 minutes, due to lack instructions and practice, plus cleaning, finding screws, and tools, Instructions may have been on line, but I didn't find them. The new hinges came with pins in place, and should have come with an extra set to lock the old hinges.
Took off oven door removed all screws to get old hinges out. Replaced with new hinges and put the door back together.
Jeff from Palm Beach Gardens, FL
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
9 of 25 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
Next >
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
2 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Richard Mccormick
March 7, 2018
I removed the door for cleaning. How do you reinstall the door? Do i need to remove the front of door to reset springs? Help!!!!
For model number SF385PEEQ
Hi Richard,
Thank you for your question. There is a video on our website that you can reference on how to install the hinge. The oven in the video may not show exactly like the one you have and the part being installed in the video is an inner door glass, but it will give you a general idea on how to install the door. You will find the video under part number PS438400. I hope this helps. Thank you and have a great day!
2 people found this helpful.
Was this helpful?
Thank you for voting!
Elie
September 20, 2022
Hi,
regarding the oven door hinges (part nbr: WP8053807) , do the package contains 2 hinges or just one. Is there a difference between left and right one? do you currently have it in stock or back order?
Thanks
For model number GERC4110PQ0
Hello Elie, Thank you for your inquiry. We show that this part is a single hinge that can be used for either the left or right hand sides, so there is no difference between the hinges for this model. The stock status for parts is always listed above the Add to Cart button on our site underneath the part information. If you are not sure what a stock status means, you can click on it and a separate window will appear with the explanation for what that status means. In the case of this part, it currently shows as in stock. We hope this helps and if you need help placing an order for a part, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you!
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
