Quick Question!

Have you ever purchased from PartSelect.com before?

11744825-1-S-Whirlpool-WP8053344-Temperature Sensor
11744825-1-S-Whirlpool-WP8053344-Temperature Sensor 11744825-2-S-Whirlpool-WP8053344-Temperature Sensor https://partselectcom.azureedge.net/Schematics/Whirlpool/VLIMJ4HW.gif

Temperature Sensor

Your Price

$31.06
Get this part fast. Average delivery time via standard shipping: 1.8 days.

PartSelect Number PS11744825
Manufacturer Part Number WP8053344
Manufactured by Whirlpool

This temperature sensor is used to measure the inside temperature of a self-cleaning oven. Its 1000-ohm resistance increases with temperature. The sensor has male leads, is 6 inches in length, and comes with 2 ceramic wire nuts. Fault temperature sensors are often responsible for F3 and F4 error messages on an electric range. Furthermore, if you find your oven is too hot, will not heat evenly, or simply will not heat at all, there could be an issue with your temperature sensor and you should look to replace it immediately.

This part works with the following brands: Whirlpool, KitchenAid, Roper, Kenmore, Estate, Crosley, Inglis, Frigidaire.

This part works with the following products: Range, Wall Oven, Microwave Oven Combo.

This part fixes the following symptoms:

  • Little to no heat when baking.
  • Oven is too hot.
  • Will Not Start.
  • Oven not heating evenly.
  • Will not program.

Questions & Answers

Ask our experts a question on this part and we'll respond as soon as we can.

Most Helpful

Question:

My oven will not hold the set temperature. It looses temp as it baked (start at 350 within 15 minutes down 25 degrees). Is this the part (temperature sensor) that i need? Thank you.

Pat for model number RS696PXYB
Answer:

Hi Pat, Thank you for your question. It definitely could be. I would suggest testing your sensor with a multi meter to see if it is working correctly. You can also test your bake element as well to make sure that it is not that part. If both of those parts are fine, it may be your electronic control board that is the issue. I hope that helps. Good luck with your repair.

Most Recent

Question:

I have replaced the ignitor & the temp. Censor , will not turn on . Do i need to clear the eo-f3 coads & how do i do that ?

danny for model number GW395LEGB3
Answer:

Hi Danny, Thank you for your question. The error code E0 F3 indicates that the oven temperature sensor in your range is open. This error code can also mean that the electronic oven control in your range has failed. Disconnect the electricity to your range for 2-3 minutes. This will reset your control if it is just confused. If this does not fix the issue, you will need to check both parts with a multimeter to see which one is causing the issue. I hope this helps. Thank you and have a great day!

Question:

My propane oven lights but goes out within 4 seconds.We changed the gas valve.Didn't solve my problem

Pamela for model number SF367LEHW5
Answer:

Hi Pamela, Thank you for the question. I suggest replacing the Bake Burner with Spark Igniter, PartSelect Number PS897264. If the igniter does not have enough Ohms it will not stay lit. Hope this helps!

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.8 / 5.0, 6 reviews What's this?
1-6 of 6
 

145 of 184 people found this instruction helpful

Parts Used:
  • Temperature Sensor
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: Charles from Brecksville, OH

F3 error message

Two screws remove the front of the sensor (put a pan under the sensor to catch the screws), One nut removes the rear cover to access the rear of the sensor. Separating the two halves of wiring harness takes a little dexterity. BIG TIP! Tie a string to the back of the sensor wire and pull the sensor out from the front making sure the string still shows thru the back. If you don't you have a 15 minute job trying to fish the wires at an angle thru the insulation (a very frustrating task). Untie the string from the old and tie it securely to the new. Pull the string from the back and Voila! your new sensor can be plugged in or wirer nutted to the old connection on the back of the stove. Replace the nut and the two screws and you're done!

Help other customers find the most helpful instructions.

Were these instructions helpful?   

46 of 85 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools:
Customer: Paul from Modesto, CA

Oven sensor quit working

simple part exchange. easy out, easy in.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

3 of 3 people found this instruction helpful

Parts Used:
  • Temperature Sensor
Level of Difficulty: Difficult
Time to do repair: 1- 2 hours
Tools: Nutdriver, Pliers, Screw drivers
Customer: Barry from WOODSTOCK, GA

Oven wouldn't heat above 300 deg. F.

I tried taking the sensor out, but the plastic coupling behind the oven wall had melted and the melted piece was larger than the opening in the oven wall. I had to use a mini-screwdriver to chip away at the melted coupling before it would fit through the opening. That took forever...but it finally worked and the repair went quickly (15 minutes) after that.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 1 people found this instruction helpful

Parts Used:
  • Temperature Sensor
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: Heriberto from AUSTIN, TX

The oven was not heating to desired temperature

DISCONNECTED POWER AND GAS TO THE RANGE. REMOVED 6 SCREWS FROM REAR OF THE RANGE. REMOVED THE 2 SCREWS HOLDING THE TEMPERATURE SENSOR IN PLACE. DISCONNECTED THE LEAD FOR THE SENSOR. INSTALLED NEW SENSOR IN REVERSE ORDER. OVEN WORKING PROPERLY NOW.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 1 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: 30 - 60 mins
Tools: Pliers, Screw drivers
Customer: Roy from Logan, NM

Oven not browning on top. Temp not adequate. Top element not producing heat.

I actually found a loose connection . After receiving parts I removed back cover. Only then did I find a loose connection to the element . I cleaned and repaired the connection and replaced the sensor which was faulty. The element awaits a time review of my decision to not use it.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 1 people found this instruction helpful

Parts Used:
  • Temperature Sensor
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: Cynthia from COVINGTON, GA

Stove got way too hot

Took the back off the stove, removed 2 screws, unclipped the bad sensor, clipped the new one on, put the screws back in and the back of the stove back on and that was it - 10 minutes

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1-6 of 6

Model Cross Reference

This part works with the following models:

PartSelect Number: PS11744825
Manufacturer Part Number: WP8053344
Brand Model Number Description
Whirlpool2492^0ARange
Whirlpool2492^1ARange
Roper2492L0ARange - Electric
Roper2492L1ARange - Electric
Roper2492X0ARange - Electric
Roper2496*0Range - Ranges, Electric*
Roper2496*0ARange - Ranges, Electric*
Roper2496*1Range - Ranges, Electric*
Roper2496*1ARange - Ranges, Electric*
Roper2496*2Range - Ranges, Electric*
Roper2496*2ARange - Ranges, Electric*
Whirlpool2496^0Range
Whirlpool2496^0ARange
Whirlpool2496^1Range
Whirlpool2496^1ARange
Whirlpool2496^2Range
Whirlpool2496^2ARange
Roper2496X0Range - Electric
Roper2496X1Range - Electric
Roper2496X2Range - Electric
Whirlpool4RF315PXDQ0Range - Freestanding, Electric
Whirlpool4RF315PXDW0Range - Freestanding, Electric
Whirlpool4RF315PXEQ0Range - Freestanding, Electric
Whirlpool4RF315PXGQ0Range - Freestanding, Electric
Kenmore6644579391Range
Kenmore664KERH507YAL0Range
Kenmore664KERH507YAL1Range
Kenmore664KERH507YBL0Range
Kenmore664KERH507YBL1Range
Kenmore664KERH507YWH0Range