Bake Igniter WP7432P143-60 | Official Whirlpool Part | Fast Shipping | PartSelect
Bake Igniter – Part Number: WP7432P143-60
( Grid squares measure 1x1 inch )
Bake Igniter – Part Number: WP7432P143-60 Bake Igniter – Part Number: WP7432P143-60 Bake Igniter – Part Number: WP7432P143-60 https://partselectcom.azureedge.net/Schematics/Maytag/59838.gif

Bake Igniter

PartSelect Number PS11744546

Manufacturer Part Number WP7432P143-60

Manufactured by Whirlpool

Product Description

Bake Igniter Specifications

This bake or broil igniter ignites the gas for the oven burner by glowing white. If any of the following symptoms occur, it is best to replace this part: little to no heat when baking, oven will not turn on, gas igniter glows, but does not light up or element will not heat. *Tip: Match up the connecter with the old part. Refer to the manual provided by the manufacturer for installation instructions and accurate guidance. As a safety precaution, remember to unplug your appliance from the power source.

How Buying OEM Parts Can Save You Time and Money

Troubleshooting

This part fixes the following symptoms:

Little to no heat when baking | Will Not Start | Gas igniter glows, but will not light | Element will not heat

This part works with the following products:

Range.

This part works with the following brands:

Maytag, Whirlpool, KitchenAid, Jenn-Air, Kenmore.

Part # WP7432P143-60 replaces these:

74007965, 7432P143-60, AP6011350.
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
10 questions answered by our experts.
Sort by:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer Repair Stories
Average Repair Rating: 3.3 / 5.0, 10 reviews What's this?
Sort by:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
David from Temple Terrace, FL
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Pliers, Screw drivers
Parts Used:
WP7432P143-60
Ignitor was bad on upper oven
First I removed the lower tray and all parts covering the ignitor on the upper oven. 2. Then I removed the screws holding down the ignitor and flame distributor. 3. I then had to pull out the oven from the wall and remove the back panel to expose the wires connecting the ignitor. This required the removal of about six screws but they were fairly easy to get to. 4. I disconnected the ignitor from the back panel then went around to the front of the oven and pulled out the ignitor and all of the attached parts. 5. Here's the tricky part. The screws holding the ignitor in place had fused from the heat and then the threads stripped when I tried to remove them. I had to use a dremel tool and cutting wheel to carefully cut the screws off and then went to buy some replacement screws from the hardware store. 6. I replaced them with a nut and a bolt, to hopefully avoid the same problem for later replacement if necessary. 7. I then replaced everything the same way it came out and all is working like new!
58 of 65 people found this instruction helpful.
Was this instruction helpful to you?
Timothy from Elkhorn, WI
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Parts Used:
WP7432P143-60
Oven would not heat
Lifted door off hinges; removed lower oven spill plate; unmounted bake igniter from heat shield; pulled stove away from wall; removed rear access panels (4 screws); unplugged bake igniter; installed new part; vacuumed behind stove and mopped floor (this took more time than installing the part); oven is back in cookie baking mode!
28 of 30 people found this instruction helpful.
Was this instruction helpful to you?
jack from springfield, IL
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Parts Used:
WP7432P143-60
upper oven would not ignite
removed panel from back 4 screws. unplugged ignitor wire to lower level of upper oven, top wire is for broiler.Slid oven door off its hinges(very heavy)removed wire rack removed 2 screws from bottom pan lifted out,lifted off burner guard, looks like it may have had nuts to hold it down at one time , mine were missing. lifted out burner assembly. removed 2 screws holding down ignitor, they stripped out had to drill holes slightly larger and install new one with screws and nuts I had on hand. Used long screw driver pushed in from behind to guide ignitor wire back thru the insulation. reinstalled everything in reverse and it worked like a new. $50 part part saved us $2000, we were looking at replacing it with a new oven but we really liked what we had. Very satisfied, and wont hesitate to tackle next repair job with help from this web site.
15 of 16 people found this instruction helpful.
Was this instruction helpful to you?
dave from williams, AZ
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Parts Used:
WP7432P143-60
replaced igniter
easy-peasy remove small panel on back
disconnect in the back of range-oven "orange wire"
unscrew igniter from burner inside oven
remove and replace with new one
slide wire thru hole in back of oven
reconnect---u r done
dave
12 of 16 people found this instruction helpful.
Was this instruction helpful to you?
James from Keno, OR
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
Parts Used:
WP7432P143-60
Upper Oven Igniter Failed
Remove door, racks, unplug, remove lower burner cover two screws, the burner tube deflector pan two wingnuts, the burner tube. With igniter attached, remove back of range 4 screws to expose connector to igniter, unplug then remove burner tube, then igniter, replace igniter feed through back of oven wall and reconnect igniter reverse process and its done
10 of 12 people found this instruction helpful.
Was this instruction helpful to you?
Michael from Minneapolis, MN
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Tools:
Parts Used:
WP7432P143-60
Oven not reaching proper temperature
Removed old ingniter with screwdriver. Installed new igniter, but had to remove connector in order to electrically connect using twist on connectors.
10 of 17 people found this instruction helpful.
Was this instruction helpful to you?
Robert from KNOXVILLE, TN
Difficulty Level:
Really Easy
Total Repair Time:
1- 2 hours
Tools:
Screw drivers
Parts Used:
WP7432P143-60
Upper oven bake igniter went bad
You Tube!!! Didn’t find my exact oven, but watching a couple of videos was extremely helpful. Replacing the igniter was basically simple, but since it was a first for me, I took my time. Probably saved $200. The part was just over $100.
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Phonsab from WHITINSVILLE, MA
Difficulty Level:
Difficult
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
Parts Used:
WP7432P143-60
Lower igniter does not light oven
I repair it by shutting off the gas. removing the back panel of the stove . unplug the electrical sensor cord to the igniter. Then replace with new one.
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Kenneth from BOWIE, MD
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Socket set
Parts Used:
WP7432P143-60
. Bottom oven would not heat
Replaced Igniter, only problem was the connector was in the back of the unit. I had to take off the back of the unit. About 12 small hex screws to make connection. Other than that it was pretty easy.
1 person found this instruction helpful.
Was this instruction helpful to you?
Cheryl from WEST YARMOUTH, MA
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Socket set
Parts Used:
WP7432P143-60
Bottom oven not heating
Easy instal most of time was taking off and replacing back panel Found watching how to videos helpful
1 person found this instruction helpful.
Was this instruction helpful to you?
Customer Reviews
Average Rating:
14 Reviews
4.9
out of 5
Filter By Rating:
  • 5 Stars
    12
  • 4 Stars
    2
  • 3 Stars
    0
  • 2 Stars
    0
  • 1 Stars
    0
Sort by:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Model Cross Reference

This part works with the following models:

PartSelect Number: PS11744546
Manufacturer Part Number: WP7432P143-60
Brand
Model Number
Description
Kenmore
66578002800
Range
Kenmore
66578002801
Range
Kenmore
66578002802
Range
Kenmore
66578002803
Range
Kenmore
66578003800
Range
Kenmore
66578003801
Range
Kenmore
66578003802
Range
Kenmore
66578003803
Range
Kenmore
66578003804
Range
Kenmore
66578009800
Range
Kenmore
66578009801
Range
Kenmore
66578009802
Range
Kenmore
66578009803
Range
Kenmore
66578009804
Range
Whirlpool
GGG388LXB00
Range - Freestanding, Gas
Whirlpool
GGG388LXB01
Range - Freestanding 30" Gas
Whirlpool
GGG388LXB02
Range - Freestanding 30" Gas
Whirlpool
GGG388LXB03
Range
Whirlpool
GGG388LXB04
Range
Whirlpool
GGG388LXB05
Range
Whirlpool
GGG388LXQ00
Range - Freestanding, Gas
Whirlpool
GGG388LXQ01
Range - Freestanding 30" Gas
Whirlpool
GGG388LXQ02
Range - Freestanding 30" Gas
Whirlpool
GGG388LXQ03
Range
Whirlpool
GGG388LXQ04
Range
Whirlpool
GGG388LXQ05
Range
Whirlpool
GGG388LXS00
Range - Freestanding, Gas
Whirlpool
GGG388LXS01
Range - Freestanding 30" Gas
Whirlpool
GGG388LXS02
Range - Freestanding 30" Gas
Whirlpool
GGG388LXS03
Range