11744497-1-M-Whirlpool-WP7403P876-60-Vent Fan Control Switch
Part Location Diagram of WP7403P876-60 Whirlpool Vent Fan Control Switch
See part 16 in the diagram
( Grid squares measure 1x1 inch )
11744497-1-S-Whirlpool-WP7403P876-60-Vent Fan Control Switch 11744497-2-S-Whirlpool-WP7403P876-60-Vent Fan Control Switch 11744497-3-S-Whirlpool-WP7403P876-60-Vent Fan Control Switch Part Location Diagram of WP7403P876-60 Whirlpool Vent Fan Control Switch
Customer Service Representative

Get in touch, we're here to help!

Daily 8am - 9pm EST

customerservice@partselect.com

Vent Fan Control Switch WP7403P876-60

Rated by 7 customers 

Really Easy 

15 - 30 mins 

Ratings submitted by customers like you who bought this part.

$ 142.34
  In Stock
Get FREE EconoShip on orders over $100! T&C apply

Get this part fast! Average delivery time for in-stock parts via standard shipping: 1.8 days.

PartSelect Number PS11744497
Manufacturer Part Number WP7403P876-60
Manufactured by Whirlpool
Product Description

Vent Fan Control Switch Specifications

Downdraft vent fan control switch activates and controls the speed of the downdraft fan motor in the cooktop.
How Buying OEM Parts Can Save You Time and Money

How Buying OEM Parts Can Save You Time and Money

Troubleshooting
This part fixes the following symptoms:
Will Not Start
This part works with the following products:
Cooktop.
This part works with the following products:
Jenn-Air.
Part# WP7403P876-60 replaces these:
AP6011301, 74009255, 7403P876-60
Back to Top
Customer Repair Stories
 Average Repair Rating: 4.3 / 5.0, 7 reviews. What's this?
Sort by:
  • 1
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
The switch worke fine but the threads was not the same as the old switch so I had to order a 3/8-32 but.
Remove the knobs then remove the four screws holding the trim remove the two sheet metal screws then lift the unit up and out of the cook top remove the nut from the old fan switch remove the two wires from the switch install the new switch put the wires back on the new switch then place the assembly back in the stove top insert and fasten the two sheet metal screws install the trim and knobs and your done. Note : check the nut before hand to see if it is the same as the old one there was no new nut with the new switch so I had to buy one.
Read less
  • James from CANTON, GA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Wrench set
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
fan switch would not work the fan
Unplugged the unit first of course. Removed the control knobs.

Removed 4 screws from the control panel on the side of the stove top.

located the fan switch and took out the two connectors. The only little problem was the little bolt that holds the fan switch in place was slightly the wrong size for the new fan switch. I had to go to the hardware store to find a bolt that would hold the switch in place within the unit.

after that was located it was very simple to plug the connectors in to the new switch and put everything back in place. If a bolt would have been included it would have been a 10 or 15 minute job.
Read less
  • Carri from Pittsburgh, PA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
4 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
fan wouldn't turn off
Removed the part that didn't work and replaced it with the new one
  • Conrad from Roswell, GA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers, Wrench set
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
I knocked the knob off the fan control and the stem of the control broke, too.
First I removed 3 screws that held a plate againt the wires. Then pulled the element out about 3 inches and disconnected the 2 wires holding the old element and connected them to the new element. Replaced the plate with 3 screws and I was done.
  • Carolyn from Cressey, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
2 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Replaced turntable motor
Removed bottom panel by removing 6 screws. Removed 2 screws holding motor and replaced.

Piece of cake! Saved a fortune. Appliance repair service wanted $380.
Other Parts Used:
Vent Fan Control Switch Drive Motor
  • David from Fulton, MD
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Exhaust fan wouldnt shut off
Piece of cake. Unplug power. Unscrew 4 screws on side. Unscrew 2 screws on top. Pull off top cover and plug in new switch. Switch was not the same but it still worked just fine. Very easy and much cheaper than paying Sears of JoeBlow $100.
  • perry from germantown, TN
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
5 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Original Fan switch wouldn't shut off.
Once I got the part from Parts Select it was easy. Removed four screws, liftef knobs and face plate. Removed two more screws , lifted assembly(after I shut off power)
Removed towo connectors and nut holding switch. Replaced with new switch and and did a reverse of proceedure to put together.
Real story was before I found Parts Select I contacted JennAir and their person couldn't understand or help me. I emailed the original manufacturer of the part and found it was obsolete. They did not offet a substitute.
10 minutes on line with PS and I had what I needed ordered.
Thank You
Read less
  • Robert from Rhinelander, WI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
8 of 8 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • 1
Back to Top
Questions and Answers

Be the first to ask our experts a question about this part!

Back to Top
You May Also Need ?
Fan Switch Knob - Black
$20.38
$20.38
  In Stock
Back to Top
Model Cross Reference
This part works with the following models:
PartSelect Number: PS11744497
Manufacturer Part Number: WP7403P876-60
Brand
Model Number
Description
Jenn-Air
CVGX2423B
Cooktop - Gas
Jenn-Air
CVGX2423B18
Cooktop - 34" GAS BUILT-IN DOWNDRAFT COOKTOP
Jenn-Air
CVGX2423Q
Cooktop - Gas
Jenn-Air
CVGX2423W
Cooktop - Gas
Back to Top
Customer Service Representative

Get in touch, we're here to help!

Daily 8am - 9pm EST

Contact Customer Service
Vent Fan Control Switch
$ 142.34
  In Stock
✖
Stock Status
 In Stock

Item is in stock and will ship today if your order is placed before 4:00 PM Eastern Standard Time.

If your order is placed after 4:00 PM EST, the in stock items will ship on the next business day.

 On Order

Item is not in stock and usually ships 3-5 business days from the time you place your order.

 Special Order

Item is not in stock and usually ships 10-15 business days from the time you place your order.

 NLA - No Longer Available

This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.