Door Hinge WP74008014 | Official Whirlpool Part | Fast Shipping | PartSelect
Door Hinge – Part Number: WP74008014
Door Hinge – Part Number: WP74008014 Door Hinge – Part Number: WP74008014 Door Hinge – Part Number: WP74008014 https://partselectcom.azureedge.net/Schematics/Maytag/33291.gif

Door Hinge

Product Description

Door Hinge Specifications

The hinges control the rate that the oven door opens and closes, and allows the door to stay open at an angle. This hinge can be used on either the left or right hand side of your oven, and is approximately 20 1/2 inches long. If your oven door will not open or close easily, you may need to replace this part. It may be a good idea to replace both hinges at the same time. If a spring has become loose on one hinge, the other hinge is likely to have the same issue. The repair is simple and only requires a Phillips screwdriver and a small bent nail. For a full step-by-step guide, check out the video below.

How Buying OEM Parts Can Save You Time and Money

Troubleshooting

This part fixes the following symptoms:

Door won’t close.

This part works with the following products:

Wall Oven, Microwave Oven Combo, Cooktop, Range.

This part works with the following brands:

Jenn-Air, Maytag, Kenmore, Amana, Magic Chef, Hoover.

Part # WP74008014 replaces these:

580073, 700834, 7-0834, 71001832, 71002869, 71003350, 7106P115-60, 74008014, JA99700834, Y700834.
Part Videos

Replacing your Jenn-Air Wall Oven Door Hinge

Customer Repair Stories
Average Repair Rating: 3.7 / 5.0, 19 reviews What's this?
Sort by:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
William from Statesville, NC
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Parts Used:
WP74008014
Oven door wouldn't close completely
Parts arrived in three days and it was an easy swap of the hinges but the same problem still existed: the oven door wouldn't close completely, so the oven light stayed on and the convection wouldn't work either unless the door closed all the way. The replacement hinge's springs apparently aren't strong enough to close it and the springs aren't adjustable - which is a design flaw. I did correct the problem though, by using three dollars worth of 1" round magnets, which I placed inside the door: they stay put and are strong enough to pull the door tight.
47 of 51 people found this instruction helpful.
Was this instruction helpful to you?
John from Harvard, MA
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
Parts Used:
WP74008014
Oven door doesn't completely close, light stays on
I replaced the hinges on the door, it wasn't that hard to do, a couple of minor things I had to overcome. But the new hinges still don't close the door completely. The light still comes on. I don't think the springs in the hinges are strong enough.

I asked for a particular part number in my order, the sales rep, said that wasn't the correct part number, and gave me a different part number. Now I'm not sure if the sales rep gave me the correct part or not.

Either way, I spent money for new hinges, and my own labor, and I still have the same problem.

I've placed calls with Jenn-air, and local technicians, but so far, do not have a solution to my problem. So overall, I'm not very happy.

Anyone got any ideas?
36 of 54 people found this instruction helpful.
Was this instruction helpful to you?
Hugh from Hopewell, NJ
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Parts Used:
WP74008014
Oven Door hinge is broken
One oven door hinge spring was broken. I ordered two hinges to complete the repair.
The repair could not have been easier. I removed the door from the oven an unscrewed the outer frame of the door from the inner door assembly. I unscrewed the old hinge assembly and replaced them with the two new hinges.
I set the door back on the oven and replaced the oven door retaining hardware.
After replacing the retaining hardware, I removed the temporary shipping pins that keep the spring assembly static. Very important: don’t remove these hinge pins until the door is on the oven an the oven retaining hardware is secured.
20 of 24 people found this instruction helpful.
Was this instruction helpful to you?
Jeff from Fremont, CA
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
Parts Used:
WP74008014
Oven Door wouldn't fully close and light stayed on.
Remove oven door by removing chrome flat plate that holds the hinge in place (one screw at each hinge) and LIFT door off oven. There is a hole in the hinge that you can stick a small nail through to hold the hinge in the "partially open" position for easier removal and replacement of the door (I didn't know this until I received the new hinges, which have a removeable pin in the hole.) After door is off, remove three screws each, on the top and bottom of door, to remove the back half of door and expose the hinges. Remove one screw from bottom of door that holds bottom of hinge in place. Lift out hinge bottom and unhook top of hinge. Reverse process to reassemble. Remove small pins by opening oven door fully. The new hinges did solve the problem. You have to order two hinges for each door. They are NOT sold as pairs.
16 of 18 people found this instruction helpful.
Was this instruction helpful to you?
Stephen from Corpus Christi, TX
Difficulty Level:
A Bit Difficult
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers
Parts Used:
5765M451-60, WP74008014
Oven door would not close properly. Believe this caused control panel to fail from overheating.
Parts arrived as scheduled with no problems. First I removed and repaced the 2 oven door hinges to see if this would fix the problem with the door not closing all the way (had to push door to get the oven light to go out). Since no instructions were shipped with the new hinges, I followed the information given by other customers on how they were able to change the hinges. Changing the hinges DID NOT fix the problem with the door! The new hinges did not pull the door any tighter than the old hinges. Door closure problem finally fixed by supergluing several round mangnets (Lowes) to the door which pulls the door tight when closed. I learned this trick from another customer's report (thanks for the idea!). Next I removed and replaced the failed control panel. This was the second panel to fail on this oven in the 5 years it has been installed! The first panel was replaced under warranty after approx 2 years of use. Hopefully, the magnets will keep the oven door closed and prevent overheating of the control panel which will allow this poorly designed oven to last a little longer this time!
15 of 25 people found this instruction helpful.
Was this instruction helpful to you?
Russ from Jacksboro, TX
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Parts Used:
WP74008014
Oven door hinges broken
Removed the door then the end caps and inner panel then the hinge system and replaced with the one piece new set of hinges and back together done in 30 to 45 minutes The new parts were a perfect replacement.
12 of 13 people found this instruction helpful.
Was this instruction helpful to you?
Louise from Cedar Rapids, IA
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
Parts Used:
WP74008014
When opening the oven door, the hinge on the left of the door broke.
We panicked cause even simple repairs on these products cost and cost.....but we remained calm and ordered the exact part necessary from you. It arrived in just 3 days and once we had the part in hand it was easy to understand how to replace it. We disassembled the door with screwdrive and swapped the broken part with the new one. The one gotcha was that we were not aware of the shipping pin holding the spring and we struggled for a few trying to get the door closed all the way. Once we discovered the pin and removed it, it was fixed and we were PLEASED!

Thank you,
Louise and Rickl
9 of 10 people found this instruction helpful.
Was this instruction helpful to you?
ALAN from OSWEGO, IL
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Parts Used:
WP74008014
Oven light stays on when door is shut.
I replaced the hinges as described in other posts and the problem was solved. When the oven was 2 years old it had the same problem but the hinges should not have fatigued at that point. The engineering problem someone mentioned is that the pin of the light switch is too short. I touched it with lipstick, closed the oven door, and opened the door to see exactly where the door touched the pin. I drilled a small hole in the door and screwed in a self tapping metal screw...problem solved for 8 years until the hinges fatigued. After replacing the hinges I tried removing the screw but the light stayed on so I put the screw back.
9 of 11 people found this instruction helpful.
Was this instruction helpful to you?
Bruno from Scottsdale, AZ
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Parts Used:
WP74008014
The Old Hinges broke off and the door would not stay closed
I removed the single screw on each side of the oven by the hinge to remove the hinge cover plate and expose the hinge opening. I lifted off the glass oven door up and out and set it on my work bench. The door is heavy because its glass so make sure the doors on the way to the garage are open to your work bench area. I installed the cover plates back on so i would not loose the little covers and screws. I removed the screws all around the door and set them in a cup and lifted up the inner part of the door and the hinges are exposed. After removing the screws that hold on the hinges it lifted right out. I cleaned all the glass and set the new hinges in and locked them down with the screws and installed back the inner part of the door to the outer part and returned all the screws back. I then removed they screws on the hinge covers. I did not loose them with 4 kids running around and lifted the door back into the hinge openings and pushed down and it locked in. I then put a little pressure down on the door and removed the little locking pins. I pushed the door all the down and installed the hinge covers back on and it works beautiful. I think the new hinges are better than the set that came with the Jenn-Air wall oven. Thanks Parts Select. Also the new hinges came in 3 days as promised.
6 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Larry from Oak Grove, MO
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Parts Used:
WP74008014
replace door hinge
The repair was very easy to perform, but the springs in the new hinge were not as strong as the old one. The door would not close all the way unless you held it closed. The hinge looked identical but spring had less tension.
5 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Customer Reviews
Average Rating:
10 Reviews
4
out of 5
Filter By Rating:
  • 5 Stars
    7
  • 4 Stars
    0
  • 3 Stars
    1
  • 2 Stars
    0
  • 1 Stars
    2
Sort by:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Model Cross Reference

This part works with the following models:

PartSelect Number: PS11744215
Manufacturer Part Number: WP74008014
Brand
Model Number
Description
Jenn-Air
12103
Cooktop - Gas
Jenn-Air
12104
Cooktop - Electric
Kenmore
123.01
Range - Kenmore Range/Stove/Oven Model 123.01 (12301, 123 01) Parts
Kenmore
12303
Range - Kenmore Range/Stove/Oven Model 12303(1988) Parts
Kenmore
20133
Range - Kenmore Range/Stove/Oven Model 20133(1988) Parts
Jenn-Air
20135
Range
Kenmore
20234
Range - Kenmore Range/Stove/Oven Model 20234(1988) Parts
Jenn-Air
20236
Range
Jenn-Air
20237
Range
Kenmore
21237
Range - Kenmore Range/Stove/Oven Model 21237(1988) Parts
Jenn-Air
21238
Wall Oven - Built-in, Electric
Jenn-Air
21239
Wall Oven - Built-in, Electric
Kenmore
21241
Range - Kenmore Range/Stove/Oven Model 21241(1988) Parts
Kenmore
21243
Range - Kenmore Range/Stove/Oven Model 21243(1988) Parts
Kenmore
21244
Range - Kenmore Range/Stove/Oven Model 21244(1988) Parts
Kenmore
21245
Range - Kenmore Range/Stove/Oven Model 21245(1988) Parts
Kenmore
21246
Range - Kenmore Range/Stove/Oven Model 21246(1988) Parts
Kenmore
213.34
Microwave Oven Combo - Kenmore Oven/Microwave Combo Model 213.34 (21334, 213 34) Parts
Kenmore
21335
Microwave Oven Combo - Kenmore Oven/Microwave Combo Model 21335(1988) Parts
Jenn-Air
21336
Microwave Oven Combo
Jenn-Air
22001
Cooktop - Electric
Jenn-Air
22112
Cooktop - Electric
Jenn-Air
22113
Cooktop - Electric
Jenn-Air
22116
Cooktop - Electric
Kenmore
22304
Range - Kenmore Range/Stove/Oven Model 22304(1988) Parts
Jenn-Air
22305
Cooktop - Electric
Kenmore
22307
Range - Kenmore Range/Stove/Oven Model 22307(1988) Parts
Kenmore
22310
Range - Kenmore Range/Stove/Oven Model 22310(1988) Parts
Jenn-Air
22401
Cooktop - Electric
Kenmore
62921238
Wall Oven