Quick Question!

Have you ever purchased from PartSelect.com before?

11743900-1-S-Whirlpool-WP71003424-Electronic Clock Control Board
11743900-1-S-Whirlpool-WP71003424-Electronic Clock Control Board 11743900-2-S-Whirlpool-WP71003424-Electronic Clock Control Board 11743900-3-S-Whirlpool-WP71003424-Electronic Clock Control Board https://partselectcom.azureedge.net/Schematics/Maytag/52303.gif

Electronic Clock Control Board

Your Price

$369.62
Get this part fast. Average delivery time via standard shipping: 1.8 days.

PartSelect Number PS11743900
Manufacturer Part Number WP71003424
Manufactured by Whirlpool

This electronic clock assembly is seven and a half inches long. It is three inches wide and is intended for use with a range's control panel.

This part works with the following brands: Jenn-Air.

This part works with the following products: Wall Oven, Microwave Oven Combo.

This part fixes the following symptoms:

  • Will not program.

Videos For installing this part.

Questions & Answers

Ask our experts a question on this part and we'll respond as soon as we can.

Most Helpful

Question:

Unable to adjust temperature in oven going thru the setup steps for over temp adjustment will not help. Do i need a new control panel?

Connie for model number JJW8527008
Answer:

Hi Connie, Thank you for your question. It could be your electronic control board that is the issue. I would suggest unplugging your appliance for about 5 minutes and then plugging it back in. If that does not reset the board you may have to replace it. Good luck with your repair.

1 person found this helpful.
Question:

Hi - my jenn air wall oven broil element will not turn off even after replacing it and letting it sit with the circuit breaker turned off. Clock appears fine but i cannot cancel the broiler. Is this the clock controller that needs to be replaced?? thanks

Kevin for model number JJW8527AAB
Answer:

Hi Kevin, Thank you for your question. It does sound like it would be your board that is the issue. That or the wiring between the two parts. I would suggest checking your wiring first to see. Good luck with your repair.

Most Recent

Question:

I've replaced the bake element and temp sensor and the bake element is still not working. The control panel seems to be working fine, just the bake element will not heat. Is there something else to try before replacing the control panel?

Mike for model number JMW9530CAW
Answer:

Hi Mike, Thank you for your question. The only other thing would be to take a look at your wiring and see if anything is showing burn marks or breakage. Other than that it would more than likely be your control board that is the issue. I hope that helps. Good luck with your repair.

Question:

Oven (bake element) will not turn off (continues to heat after multiple hits of the "cancel" button), and clock light is no longer visible (won't light up). Which part do I need to repair it?

Ed for model number JMW9530AAW
Answer:

Hi Ed, Thank you for the question. Yes the Electronic Clock Control Board will need to be replaced. The board controls the the oven and when defective can cause the issues you are having. Hope this helps!

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.3 / 5.0, 51 reviews What's this?
1-15 of 51
 

52 of 53 people found this instruction helpful

Parts Used:
  • Electronic Clock Control Board
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver, Screw drivers
Customer: Cheryl from Mesa, AZ

No clock display

1. Turned off the circuit breaker for the oven.
2. Opened oven door used a phillips screwdriver to remove four black screws from under the top panel.
3. Lifted panel slightly & removed from oven.
Removed four screws using 1/4" nut driver to remove old display unit. Disconnected three wire harnesses.
4. Connected three wire harnesses to new display unit & replaced four nut screws.
5. Hang the top panel on the top of oven & replace four screws removed in step 2.
6. Turn on the circuit breaker for the oven.
("Very easy! I'm a 63 yr. old woman!)

Help other customers find the most helpful instructions.

Were these instructions helpful?   

19 of 19 people found this instruction helpful

Parts Used:
  • Electronic Clock Control Board
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers, Socket set
Customer: Herb from Seminole, FL

The clock and temperature control became dim and unreadable.

First I turned off the power at the breaker. Then I removed the 4 screws holding the panel in. These screws are located under the panel and accessed when the oven door is opened. The only caution is not to take all the screws out. Just the 4 that hold in the front panel.The panel came off by lifting it and pulling it slightly forward. Then I removed the 3 wiring harnesses. I then used a 1/4 inch socket wrench to remove the (4) screws and replaced the clock unit with the new one. I tightened the 4 screws, re-installed the wiring harnesses and swung the panel back in place . I then locked it in place with the 4 screws on the bottom of the panel. When I turned on the power and my wife saw the lit up clock she was so happy! End of story.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

14 of 19 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver, Screw drivers
Customer: Robert from South Euclid, OH

Burner will not heat, display will not light

Two separate problems. The display gradually dimmed over time and finally went out completely. It was really easy installing the new display module. I analyzed the old one and found an 68uF electrolytic capacitor (<$1) that was bad. Don't know if any other component was bad. In looking at the display module it seems it was way over-priced at over $200. The second problem is that one of the small burners had a open heating wire. The installation of the new burner was OK except the new unit did not have any clips to hold it in place. I couldn't transfer the old clips over. So I just placed it under the holding bracket and hoped that it wouldn't move while I was putting the unit back in place and it didn't. So that is working OK now.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

12 of 13 people found this instruction helpful

Parts Used:
  • Electronic Clock Control Board
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Nutdriver, Screw drivers
Customer: John from Tempe, AZ

Clock digital read out dim to non-existant

This was soooo easy, yes even you Mr. All thumbs, can do it. First it was nice to receive the exact parts I needed from PartsSelect. I needed to take the 4 screws that held the wall oven in place and pull it out about 1". Then, using a battery powered screw driver I removed 4 screws for under the Clocks panel, (you'll need to open the door, can you handle that?). After you've done that simply lift the Glass up and off by grasping the panel and with thumbs on the bottom tilt bottom toward you as you lift up, comes right off. Now disconnect the wire ribbons (4 of them) to seperate the panel from the oven and set the panel down on a towel on the table. Now using a nut driver take out 4 "nuts" and replace the clock card. Be sure to wipe off the INSIDE of the glass panel while you have the card out, and wipe the cards glass so the digital readout will be crystal clear. Re-assemble in the reverse order and you are done. Should take you less then 15 minutes and your wife will think you are a hero! (or you wives can do it and impress the husband!)

Help other customers find the most helpful instructions.

Were these instructions helpful?   

7 of 8 people found this instruction helpful

Parts Used:
  • Electronic Clock Control Board
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Nutdriver, Screw drivers
Customer: Robert from LEXINGTON, MA

The cooking/time display had become very dim

1. Turn off the circuit breaker for the oven
2. Open oven and using a phillips screwdriver remove four black screws from under the top panel.
3. Lift panel slightly and remove from oven. Disconnect three wire harnesses.
4. Remove the old display unit by taking out the four screws using a 1/4" nut driver.
5. Install the new display unit using the four screws
from step 4.
6. Hold the top panel close to the top of the oven and attach the three wire harnesses.
7. Hang the top panel on the top of the oven and replace the four screws removed in step 2.
8. Turn on the circuit breaker for the oven.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

5 of 6 people found this instruction helpful

Parts Used:
  • Electronic Clock Control Board
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Nutdriver, Screw drivers
Customer: Rod from Denton, TX

Clock/display went dim to dark

First I did it wrong-then I came and read how the 64 yr old lady it and she was spot on. First-turn off power to unit. Take off the 4 screws holding the upper part with the clock in it . (OPen the oven door for access) Then lift up slightly and pull the upper unit out. CLock is right there held on by 4 1/4 inch screws. Remove screws, unplug wiring and reinstall using reverse procedures. Then turn power back on. REady to go

Help other customers find the most helpful instructions.

Were these instructions helpful?   

3 of 3 people found this instruction helpful

Parts Used:
  • Electronic Clock Control Board
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver, Screw drivers
Customer: Joseph from Macon, GA

Over a period of a few months, the digital diplay gradually faded out until no longer visible

Searching the internet, I found the part I needed for the lowest price at PartSelect.com. I reviewed the exploded parts diagram for my oven at PartSelect.com to get a general overview of how the oven was assembled - then I read the customer stories to get some hints from those who had done this repair before. My oven is a combination wall oven with a microwave on top. First, I shut off the power to the oven at the breaker box and then removed the thin, long rails from each side of the oven using a philips screwdriver to remove the 4 screws. This then allowed me to remove the plastic faceplate from around the microwave. Opening the oven door, I found 4 philips pan head screws underneath the control panel and removed them. The control panel will then easily lift up and then out. There are 3 areas where you must disconnect electrical connections on the control module - pay a bit of attention here, but they are sized differently and are not hard to match back up appropriately when you reconnect them to the new module. These connection plugs pull straight out with no tool needed. The old control module is held in place with 4 hex-head screws I removed with a nutdriver. After you remove the old module, it is a good time to clean the inside of the clear diplay area of the front panel with a paper towel dampened with a bit of window cleaner. Allow this to dry and then install your new control module reversing the procdures you used to remove it and reverse the procedures to reinstall the control panel, the microwave faceplate and the side rails. Cut the power back on and sit back as your wife finally thinks you are the genius that you truly are........

Help other customers find the most helpful instructions.

Were these instructions helpful?   

3 of 3 people found this instruction helpful

Parts Used:
  • Electronic Clock Control Board
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Socket set
Customer: Julie from Parkersburg, WV

No time/temperature display

Screws removed from below panel. The most difficult procedure was removing the panel from the oven unit to get to the part. After lifting up and out, the panel back was revealed. Disconnected old part by pulling the three connections and replacing with new part.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

3 of 4 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver, Pliers
Customer: Sally from Keene, NH

No readout on time/temperature panel and door wouldn't stay closed.

Replacing the electronic Clock Assembly was a piece of cake - just as earlier DIYers had experienced.

The door hinges were not any harder to replace, but it does not affect the behavior of the door. The light stays on unless we keep the door closed with a hook and anchor ( bent piece of metal and a wooden wedge). Not pretty, but effective. Obviously a design flaw... keeping door closed in this way forces all airflow to top and has melted the paint into a wrinkled surface. We had a service person replace the gasket seal and hinges before, but the problem still persists. I did discover that soaking the light cover in a cola drink overnight did a splendid job of cleaning off the gunk.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

3 of 4 people found this instruction helpful

Parts Used:
  • Electronic Clock Control Board
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: John from Upland, CA

Clock not illuminated, controls not responding

Turned off power at beaker box. Opened oven door. Removed four screws from botton of display panel. Lifted display panel up and out to remove. Unplugged three wire bundles from back of circuit board. Removed four screws holding circuit board and replaced circuit board. Reassembled panel. Turned power back on. Presto.....saved $200.00 from repair estimate.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

2 of 2 people found this instruction helpful

Parts Used:
  • Electronic Clock Control Board
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: Stan from San Marcos, CA

Same as all the others. Display went dim over the last two months.

Same as the others to get to the bad clock. My old part was a circuit board which was made with white material and manufactured by RoberShaw. The new one was on a green material and by another manufacture. The new one felt a little heavier and look like there were more componets on it. However the plug-in connections and the mounting method was exactly the same. Before reassembly, I used a long handled brush to clean out most of the baking gunk that
had accumulated in this area and I used a clean wipeing cloth to clean the inside glass for the display. The best thing about this was the part came on the Thursday before
Hollowee, I installed it as soon as I got home from work. My wife started baking cookies and cup cakes for trick or
treat and all is well.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

2 of 2 people found this instruction helpful

Parts Used:
  • Electronic Clock Control Board
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Nutdriver, Screw drivers
Customer: daniel from manlius, NY

The display would not light

I removed the four screws holding the control panel to the oven. I then lifted off the panel and rested it on the the oven rack which I set in the top position and pulled out about a foot. Next, I removed the three plug in cables and removed the two screws from the frame that was holding the clock assembly in place. I put in the new part and reversed the procedure. Total time to replace part was six minutes.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

2 of 3 people found this instruction helpful

Parts Used:
  • Electronic Clock Control Board
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Nutdriver
Customer: glen from manchester, NH

Display was dim

Removed the display panel with 4 screws. Then disconnected the wires and plugged in the new display panel. Turned on the power again and it was brand new.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

2 of 3 people found this instruction helpful

Parts Used:
  • Electronic Clock Control Board
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: Frank from Petoskey, MI

Led clock display not lit

I took out 4 screws under the display panel. Lifted the panel up and off the oven. It was connected to 3 or 4 plugs on the control panel. I unplugged them and un screwed the control panel and screwwd the new panel in replugged the wires into the panel. walla it worked.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 1 people found this instruction helpful

Parts Used:
  • Electronic Clock Control Board
Level of Difficulty: A Bit Difficult
Time to do repair: 30 - 60 mins
Tools: Pliers, Screw drivers
Customer: Jane from West Chester, PA

Clock display stopped working

Followed the very clear instructions written by others who also had a combination microwave/oven. Complication encountered because my oven is built into the cabinetry right next to a built-in refrigerator that protrudes by several inches. No room to get a screwdriver in to loosen the screws for the faceplate of the microwave on one side in order to remove the oven's display panel. Luckily had just the tip of a Phillips head and used pliers to carefully turn it just a bit with each turn until screw came out. Also didn't have the right tool to loosen the clock display little hex screws and used pliers for that as well. It was tough to get two of the electrical connections out--had to be careful wiggling them free so as not to break the wires. Finally used a tiny little flathead screwdriver to gently work each side up a bit until the whole connection could be pulled out. Took longer than it needed to.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1-15 of 51

Model Cross Reference

This part works with the following models:

PartSelect Number: PS11743900
Manufacturer Part Number: WP71003424
Brand Model Number Description
Jenn-AirJEW8527AABWall Oven - Built-in, Electric, Wall
Jenn-AirJEW8527AAWWall Oven - Built-in, Electric, Wall
Jenn-AirJEW8530AABWall Oven - Built-in, Electric, Wall
Jenn-AirJEW8530AAWWall Oven - Built-in, Electric, Wall
Jenn-AirJEW9527AABWall Oven - Built-in, Electric, Wall
Jenn-AirJEW9527AAWWall Oven - Built-in, Electric, Wall
Jenn-AirJEW9530AABWall Oven - Built-in, Electric, Wall
Jenn-AirJEW9530AASWall Oven - Built-in, Electric, Wall
Jenn-AirJEW9530AAWWall Oven - Built-in, Electric, Wall
Jenn-AirJJW8527AABWall Oven - Built-in, Electric, Wall
Jenn-AirJJW8527AAWWall Oven - Built-in, Electric, Wall
Jenn-AirJJW8527BABWall Oven - Built-in, Electric, Wall
Jenn-AirJJW8527BAWWall Oven - Built-in, Electric, Wall
Jenn-AirJJW8527CABWall Oven
Jenn-AirJJW8527CASWall Oven
Jenn-AirJJW8527CAWWall Oven
Jenn-AirJJW8530AABWall Oven - Built-in, Electric, Wall
Jenn-AirJJW8530AAWWall Oven - Built-in, Electric, Wall
Jenn-AirJJW8530ACBWall Oven - Built-in, Electric, Wall
Jenn-AirJJW8530ACWWall Oven - Built-in, Electric, Wall
Jenn-AirJJW8530BABWall Oven - Built-in, Electric, Wall
Jenn-AirJJW8530BAWWall Oven - Built-in, Electric, Wall
Jenn-AirJJW8530BCBWall Oven - Built-in, Electric, Wall
Jenn-AirJJW8530BCWWall Oven - Built-in, Electric, Wall
Jenn-AirJJW8530CABWall Oven
Jenn-AirJJW8530CASWall Oven
Jenn-AirJJW8530CAWWall Oven
Jenn-AirJJW8530CCBWall Oven
Jenn-AirJJW8530CCWWall Oven
Jenn-AirJJW9527AABWall Oven - Built-in, Electric