Quick Question!

Have you ever purchased from PartSelect.com before?

https://www.partselect.com/Schematics/Maytag/49999.gif
See part 3 in the diagram
https://www.partselect.com/Schematics/Maytag/49999.gif

Electronic Clock Control Board

Your Price

$374.82
Get this part fast. Average delivery time via standard shipping: 1.8 days.

PartSelect Number PS11743858
Manufacturer Part Number WP71001799
Manufactured by Whirlpool

This electronic board is located within the control panel.

This part works with the following brands: Jenn-Air.

This part works with the following products: Range, Wall Oven, Microwave Oven Combo.

This part fixes the following symptoms:

  • Will not program.
  • Touchpad does not respond.
  • Will Not Start.
  • Timer will not advance.
  • Little to no heat when baking.

Questions & Answers

Ask our experts a question on this part and we'll respond as soon as we can.

Most Recent

Question:

Will this part fix the f1 error code, with incessant beeping?

John for model number SVE47600W
Answer:

Hi John, Thank you for your inquiry. The F1 error code means that either your touch pad or this part is defective. You should go through your touch pad test to see if that is the part that is the one not working. First disconnect the power to your appliance. Take apart your control area so that you can gain access to this part. Disconnect the ribbon coming from the touch pad to this part. Make sure that there are no loose wires so that a short does not occur when you turn the power back on in your appliance. Leave the parts unplugged for about a minute. Then reattach your ribbon and put your appliance back together. Turn your power back on. Wait for another minute. If your F1 error code is still there, then you will know that it is this part that is the problem instead of the touch pad. I hope that helps!

1 person found this helpful.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.1 / 5.0, 108 reviews What's this?
 

1 of 2 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Nutdriver
Customer: Matthew from Littleton, CO

Self cleaning inoperable, display very dim/unreadable

First, DISCONNECT POWER or you can turn your panel into an arc welder. After that removed four screws that hold front panel in place and 2 screws that hold the display in place. disconnect ribbon cable and two other cables. Reverse operation for assembly.

For the self cleaning problem, replace door lock switch by pulling forward, use needle nose to remove & replace connector. Push into place. Very easy. Total 10 minutes for both jobs

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 2 people found this instruction helpful

Parts Used:
  • Electronic Clock Control Board
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver, Screw drivers
Customer: Joseph from Moline, IL

Clock / oven temp display went dim then out.

cut off power to stove & made sure it was OFF.
removed the few screws on the underside of front cover.
lift cover and un-screw the clock/display
I then removed the wire strip feeds (one has friction tabs that need to be lifted before you pull it.. it's the flat ribbon cable use the butter knife to lift the tabs...easy does it)
put the new clock in and reconect the wires. push the ribbon in and push the tabs.
All done and saved $160.00 bucks

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 2 people found this instruction helpful

Parts Used:
  • Electronic Clock Control Board
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers, Socket set
Customer: James from Clarksville, MD

The panel display was fading/dimming.

I shut down power at the circuit breaker, removed the stove knobs, unscrewed the underneath screws of the front panel, pulled off the panel, and the electronic board/panel was there.

I unhooked the wires (3 sets), and used the socket to remove the electronic board from the front panel. I put it all back together. Very easy-- less than 15 minutes!

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 2 people found this instruction helpful

Parts Used:
  • Electronic Clock Control Board
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: Marcee from Houston, TX

We had no clock, timer, temperature display.

Removed 8 screws and replaced the part (also did a good cleaning while we were in there)! Easy breezy!!!

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 2 people found this instruction helpful

Parts Used:
  • Electronic Clock Control Board
Level of Difficulty: A Bit Difficult
Time to do repair: 15 - 30 mins
Tools: Nutdriver, Screw drivers
Customer: Tim from Springfield, PA

Display not working

The part came right away!
Removed six screws from above door, than pull knobs off and remove four screws that were under knobs.
Front panel pulls off. Remove display and put back together.
Peice of cake.
Wish all my projects were that easy!

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 2 people found this instruction helpful

Parts Used:
  • Electronic Clock Control Board
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers, Wrench set
Customer: David from Valley Springs, CA

Very dim lights and numbers

Popped it in and now we have a well lighted control panel AND a night light for the kitchen. Just wish Jen air would design a longer lasting part!!!

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 3 people found this instruction helpful

Parts Used:
  • Electronic Clock Control Board
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Nutdriver, Screw drivers
Customer: Robert from Trenton, OH

The oven "read-out" was gone. Everything worked fine but you had to be very carefull with your entry.

After throwing the breaker. The repair consisted of removing the screws that held the control panel "housing" together. I think it was seven screws. I then disconnected the three electrical connections. The "ribbon" connection seamed delicate so I was careful. the control assembly is then loose. I removed the clock control panel with a nut driver (four screws). The installation process was just a reverse of what I have already described. It really was a piece of cake.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
  • Electronic Clock Control Board
Level of Difficulty: Easy
Time to do repair: 30 - 60 mins
Tools: Nutdriver, Screw drivers
Customer: Roger from Oak Island, NC

The clock display had dimmed out.

The expert said to replace the clock control and linked to the replacement part. The part was promptly shipped. The only difficult part of the repair turned out to be the removal of the ribbon from the old controller. I noted the tabs on the side of the ribbon receptacle and expected the ribbon to release when these were pushed in. What was actually needed was to not only push in but also to pull upward on the tabs in order to release the ribbon. That was not obvious and it took me a while to get the ribbon released.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
  • Electronic Clock Control Board
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver, Screw drivers
Customer: Ralph from Louisville, KY

No lights on control panel - oven worked

My electrical engineer son was skeptical of my diagnoses and wanted to be there so I didn't electrocute myself. Opened oven door so interior light came on. Went to circuit box and opened proper circuit (previously determined). Light went off. Started timing,removed 7 seven screws, I held the panel while my son removed the wires from connections. I expected the long multi-wire to release from the panel, but only a part of it came up when we squeezed the ends which released the wires. Removed four hex-head screws, put new panel in place, re-installed screws, inserted multi-wires into connector, connected the other two wires, re-installed the 7 screws, closed circuit breaker. 17 minutes. Set clock. Works like a new one. It appears the display unit lost vacuum. One small black spot like a burned incandecent filament. Engineer was impressed.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
  • Electronic Clock Control Board
Level of Difficulty: Really Easy
Time to do repair: 30 - 60 mins
Tools: Screw drivers
Customer: Jim from Statesville, NC

Led

Pulled front panel off (after removing power) installed led display. Closed panel re-applied power system checked ok.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
  • Electronic Clock Control Board
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver, Screw drivers
Customer: Danny from Plymouth, MN

Clock display had completely gone out

Followed other's comments about process. Opened door then removed 4 hexnuts from bottom of stove control panel. Removed hexnut from each triangular side panel of control panel. Removed side panel (it did break off a screw area near the top of the panel, but did not negatively affect reassembly. Control panel slid down and tilted out so I could see the backside of the clock control circuit card. Removed 2 small cables. The flex cable is removed by pushing in on the small ears on each side of the connector. The cable has a couple of holes which are over protusions on the connector, so be careful. Removed the 2 hex nuts holding the board down, and put in the new one. Put cables back on as removed - the near side of the flex cable connector is free to slide up about 1/8 inch when ears on both ends of connector are pushed in. When raised, put the flex cable in place and push in (along with the side of the connector) until it is latched in place. This took me the longest since I was being careful here, but no more than 10 minutes. Then put control panel back in place, and put triangular end pieces back on panel and attach with hex nut, then put 4 front hex nuts back in place. Worked fine!! Thanks for everyone's encouragement and help in understanding what I would find during this process.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
  • Electronic Clock Control Board
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver, Screw drivers
Customer: Kevin from Crooked River Ranch, OR

Electronic control faded out

Thanks to all of the previous do-it-yourself repairers. With those instructions it was quite simple to do the repair. The only glitch I had was trying to get the ribbon back into the new unit. That was until I looked at the old unit and finally figured out how to release the new unit lock. Then it was a simple process to install the ribbon. My biggest problem was finding my close-up glasses so I could actually SEE what I was doing.

Thanks,
Kevin

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
  • Electronic Clock Control Board
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: Ila from Carthage, NC

Oven will not heat

Installed it by dropping the front plate down, removing the 2 screws that held the clock in place and then unsnapped the wires and did the reverse to attach new clock.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
  • Electronic Clock Control Board
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: John W. from Durant, OK

The led display went blank over a period of 6 mo.

I removed the 4 control knobs, removed 4 screws behind the knobs, removed 4 screws on bottom of panel. lifted front panel, off of stove, unplugged wiring on back and placed new panel by reversing process. Works great. Like new. Very easy if you have any experience working with appliances or most any kind of mechanical experience. Simple and straight forward.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
  • Electronic Clock Control Board
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver, Screw drivers
Customer: Dennis from Carrollton, GA

The clock display had dimmed, and then disappeared.

I totally disassembled the stove top (which turned out to be unnecessary). All that needed to be done was to remove the control knobs, and the four screws that hold the face on. The face, with the clock module attached, lifts off the range (with a little effort). The clock module can then be removed by removing two screws and three electrical plugs. The largest plug is actually the end of a ribbon cable. It has no plug on it. You just put it in the plug on the new clock module and engage the latch on the plug. Reconnection of the other two plugs is obvious.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

Model Cross Reference

This part works with the following models:

PartSelect Number: PS11743858
Manufacturer Part Number: WP71001799
Brand Model Number Description
Jenn-AirSCE30600BRange - Slide-in, Electric
Jenn-AirSCE30600BCRange - Slide-in, Electric
Jenn-AirSCE30600WRange - Slide-in, Electric
Jenn-AirSCE70600BRange - Slide-in, Electric
Jenn-AirSCE70600WRange - Slide-in, Electric
Jenn-AirSVD48600BRange - Slide-in, Electric-Gas Combo
Jenn-AirSVD48600BCRange - Slide-in, Electric-Gas Combo
Jenn-AirSVD48600WRange - Slide-in, Electric-Gas Combo
Jenn-AirSVD48600WCRange - Slide-in, Electric-Gas Combo
Jenn-AirSVE47500BRange - Slide-in, Electric
Jenn-AirSVE47500WRange - Slide-in, Electric
Jenn-AirSVE47600BRange - Slide-in, Electric
Jenn-AirSVE47600BCRange - Slide-in, Electric
Jenn-AirSVE47600WRange - Slide-in, Electric
Jenn-AirSVE87600BRange - Slide-in, Electric
Jenn-AirSVE87600WRange - Slide-in, Electric
Jenn-AirW27400BWall Oven - Built-in, Electric, Wall
Jenn-AirW27400WWall Oven - Built-in, Electric, Wall
Jenn-AirW30400BWall Oven - Built-in, Electric, Wall
Jenn-AirW30400BCWall Oven - Built-in, Electric, Wall
Jenn-AirW30400PWall Oven - Built-in, Electric, Wall
Jenn-AirW30400PCWall Oven - Built-in, Electric, Wall
Jenn-AirW30400PFWall Oven - Built-in, Electric, Wall
Jenn-AirW30400PGWall Oven - Built-in, Electric, Wall
Jenn-AirW30400PKWall Oven - Built-in, Electric, Wall
Jenn-AirW30400PRWall Oven - Built-in, Electric, Wall
Jenn-AirW30400PUWall Oven - Built-in, Electric, Wall
Jenn-AirW30400WWall Oven - Built-in, Electric, Wall
Jenn-AirW30400WCWall Oven - Built-in, Electric, Wall
Jenn-AirWM27460BMicrowave Oven Combo