Dual Water Inlet Valve WP67006531 | Official Whirlpool Part | Fast Shipping | PartSelect
Dual Water Inlet Valve – Part Number: WP67006531
Dual Water Inlet Valve – Part Number: WP67006531 Dual Water Inlet Valve – Part Number: WP67006531 Dual Water Inlet Valve – Part Number: WP67006531 Dual Water Inlet Valve – Part Number: WP67006531 https://partselectcom.azureedge.net/Schematics/Maytag/GA45CTXM.gif

Dual Water Inlet Valve

Product Description

Dual Water Inlet Valve Specifications

This is a dual water inlet valve for your refrigerator/freezer. The water inlet valve is a solenoid-operated switch that, when activated, releases water from the supply line into the water valve. The liquid will then be sent to the compact icemaker mold and to the water line. You will need to replace this part if you are experiencing leaking, or your appliance is not properly dispensing water or ice. This model is blue/green in color and is roughly 3 inches wide, 5 inches long, and 4 inches thick.

How Buying OEM Parts Can Save You Time and Money

Troubleshooting

This part fixes the following symptoms:

Leaking, Not dispensing water, Ice maker not making ice.

This part works with the following products:

Refrigerator.

This part works with the following brands:

Amana, KitchenAid, Whirlpool, Maytag, Kenmore, Jenn-Air, Dacor, Hardwick, Magic Chef.

Part # WP67006531 replaces these:

12544118, 67006531.
Questions and Answers
Ask our experts a question on this part and we'll respond as soon as we can.
Sort by:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Gene
February 26, 2018
Water pump i need the piece that holds the water line down in the Green fitting.Possibly a blue piece like is on the other two connections. Is it included?
For model number JBL2088HES
Hi Gene, Thank you for your question. You should not need a fitting. You should be able to push the tubes right in. Here is some information that a customer posted on our website as to how he installed the part, "This is the 2nd time I have used PartSelect, and this experience was as pleasant as the 1st. The exploded-view diagrams make parts identification very easy; and the photo of the actual part is such a great idea, it allows you to verify what you need. I also got my part (cross country, in 3 days) Repair Procedure: Shut off water supply. It may be easier to work if you disconnect the water supply tube, but it is not required. On the backside of the refrigerator, remove the bottom, black plastic protection panel. You will need a nut driver or battery-powered screw driver with a 3/8" socket tip on it. Next, remove the black metal panel that holds the water inlet valve in place. Remove screws with a nut driver. 1st remove the two flat-pin power connectors. (They are different sizes and color-coded, so there is no room for making a re-hookup mistake). Then proceed to remove the hoses. The hoses are pressure-lock tubing, so push the plastic disk in or down where the tube goes into the main body of the valve. Do this for all three hoses (tubes). Switch water valves and reverse the procedure. **Be certain that the tubes are pushed back in as far as they can go; if you do not re-seat the tubes, the pressure from the water going back in the valve, will blow the tubes right out the valve (ask me how I know this!). Once reassembled, turn the water back on slowly. Make sure you turn the water supply valve all the way open, it seats itself internally when you do and is less prone to drip leaks. That's it! (As a former kitchen remodeler, I find this a great DIY project)." I hope this helps. Thank you and have a great day!

3 people found this helpful.

Was this helpful?
Jim
October 24, 2017
The problem i am having is with my almost 10 year old refrigerator. It is making "hollow" and or light ice cubes and the water dispenser is coming out in just a dribble or lacking any pressure. I replaced the water filter and tested the water pressure (that was a steady stream). What else do i need to check?
For model number GX5SHTXTS00
Hi Jim, Thank you for your question. I would suggest checking your water inlet valve to see if it is working correctly. It seems like that may be the part that is the issue. You can test that part with a multi meter to check it. Good luck with your repair.

2 people found this helpful.

Was this helpful?
Jim
January 21, 2019
Mzd2766ges Maytag plus has minor water leak at water dispenser. Would one replace water inlet valve or dual water inlet valve assembly first?
For model number MZD2766GES
Hello Jim, thank you for your question. If the leak isn't coming from the broken water dispenser tube we would recommend testing the Limit Switch - 2 Terminal Part Number: WP61005520 and both water valves to see if they have failed. If the water valves remain open the water will come from the valve continuously. I hope this helps!

1 person found this helpful.

Was this helpful?
Mike
April 17, 2019
When I look up my model two different "dual water valves" come up. One is $20 different than the other and the bracket looks slightly different. Do either fit? Or do I need to remove mine first to pick the correct one? Tnx, Mike
For model number JBC2088HTB
Hello Mike, thank you for your question. Either Dual Water Inlet Valves parts PS11743697 or PS11743618 will fit your model. One is just a more recent replacement than the other. We hope this helps.

1 person found this helpful.

Was this helpful?
Steve
23 days ago
When i push the button to get water dispensed on the inside wall, there is a loud chattering noise. Sometimes stopping and starting the water flow makes the noise stop. Is there a solenoid valve that controls the water flow and can it be easily replaced?
For model number KBFS25EVMS0
Hi Steve, thank you for your question. Yes, your water inlet valve. We have a video that you can view on our YouTube channel on how to replace parts like this: https://www.youtube.com/watch?v=ob8Jxuv4TbI. Good luck with your repair.

1 person found this helpful.

Was this helpful?
Eric
August 2, 2018
I was getting no water flow to the dispenser, and no ice production. I have water pressure to the dual water inlet valve, and just replaced the dual inlet valve. But still no water flow. I have the filter bypass cap in place too. Any suggestions to try next?
For model number kbrs22etss01
Hello Eric, thank you for writing. I would suggest checking the limit switch, part number PS11738544. This is the switch that activates the the valve to allow water to come out of the spout. I hope this helps!

Was this helpful?
Mike
October 13, 2017
Water is not getting to the ice maker. It is however getting to the dispenser in the fridge itself. How do I know if the water valve is working or not. I can hear and see the ice maker going through it's cycle, just not making ice.I already replaced the filter.
For model number 596.76604600
Hi Mike, Thank you for the question. The valve has two sides, one for the ice maker and one for the dispenser. In some cases when the valve becomes defective it is only on one side, so it is possible for the ice maker side to be defective and have the dispenser still operating. You are able to test the valve with an Ohm meter. Here is a link on how to test the valve. Hope this helps! https://www.partselect.com/Refrigerator+test-water-valve+repair.htm

Was this helpful?
James
November 8, 2017
My maytags water dispenser steadily pours water out of door. Would this be due to water inlet valve? Single switch for water and ice in door works when on ice function.
Hi James, Thank you for the question.This would most likely be caused by the water inlet valve becoming "stuck" open and allowing water through to the dispenser. Hope this helps!

Was this helpful?
Rich
April 17, 2018
Hi, my ice maker for my Maytag mfc2061kes recently stopped working. The ejector spins, but there is no water filling the tray. The internal water dispenser is still working so I assume this means the solenoid/input valve is working. At this point, I assume the entire ice maker assembly needs to be replaced. Please advise.
For model number MFC2061KES
Hi Rich, Thank you for the question. The valve has two sides, one for the dispenser and one for the ice maker. I suggest testing the valve with a multi meter to check for continuity before replacing the ice maker. Hope this helps!

Was this helpful?
Rich
April 18, 2018
An update to my question below: I also hear a constant clicking/tapping sound. Does this mean the ice maker assembly is the issue? ——————————————. Hi, my ice maker for my Maytag mfc2061kes recently stopped working. The ejector spins, but there is no water filling the tray. The internal water dispenser is still working so i assume this means the solenoid/input valve is working. At this point, i assume the entire ice maker assembly needs to be replaced. Please advise.
For model number Mfc2061kes
Hello Rich, thank you for your question. The valve should be tested on the icemaker side, first, just to be sure water is coming from the valve to the icemaker. It is possible for one port to be faulty, and the other to be bad. This link will give you information on testing the valve. https://www.partselect.com/Refrigerator+test-water-valve+repair.htm If the test you conduct with your icemaker water inlet valve does not produce the above results, then you should replace the component. If the water valve passes the test, the icemaker itself would need to be replaced. The clicking you hear may be coming from the front of the icemaker, where the motor module is located. The clicking might be the icemaker attempting to run through the cycles for calling for water, freezing, dumping. I hope this helps!

Was this helpful?
Customer Repair Stories
Average Repair Rating: 3.3 / 5.0, 11 reviews What's this?
Sort by:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
JIM from Greeley, CO
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver
Parts Used:
WP67006531
Refrigerator sat in storage in sub zero weather, water in Dual Water Inlet Valve froze, cracking valve.
This is the 2nd time I have used PartSelect, and this experience was as pleasant as the 1st. The exploded-view diagrams make parts identification very easy; and the photo of the actual part is such a great idea, it allows you to verify what you need. I also got my part (cross country, in 3 days)

Repair Procedure: Shut off water supply. It may be easier to work if you disconnect the water supply tube, but it is not required. On the backside of the refrigerator, remove the bottom, black plastic protection panel. You will need a nut driver or battery-powered screw driver with a 3/8" socket tip on it. Next, remove the black metal panel that holds the water inlet valve in place. Remove screws with a nut driver. 1st remove the two flat-pin power connectors. (They are different sizes and color-coded, so there is no room for making a re-hookup mistake). Then proceed to remove the hoses. The hoses are pressure-lock tubing, so push the plastic disk in or down where the tube goes into the main body of the valve. Do this for all three hoses (tubes). Switch water valves and reverse the procedure. **Be certain that the tubes are pushed back in as far as they can go; if you do not re-seat the tubes, the pressure from the water going back in the valve, will blow the tubes right out the valve (ask me how I know this!). Once reassembled, turn the water back on slowly. Make sure you turn the water supply valve all the way open, it seats itself internally when you do and is less prone to drip leaks. That's it! (As a former kitchen remodeler, I find this a great DIY project).
107 of 116 people found this instruction helpful.
Was this instruction helpful to you?
Brian from Easton, PA
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers
Parts Used:
WP67006531
Water leaking from Water Inlet Valve
Ok, pretty easy repair when the parts are correct (first part was faulty, parts select quickly sent me a new one)

First is removal, these tubes are in there very tight, they can be pulled out but weaken the lines and it is not likely to work without severly stretching the line to the point of breakage, if you have to cut them do so carefully and take off as little tubing as possible as you need the length to feed from top to bottom.

Once you have cut all the lines, or pulled them out (I was able to get 2 out without cutting) then make sure the edges are smooth, attach the inlet valve to the plate and just push them tightly into the new valve making sure you route the lines correctly.

Turn everything on and run the water line to see if it works. If no leaks, screw it back to the refrigerator and you are good to go. Takes maybe 20 minutes at most.
21 of 26 people found this instruction helpful.
Was this instruction helpful to you?
LOUIE from WESLEY CHAPEL, FL
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
Parts Used:
WP67006531
No Water Dispensing
4-Screws 3 plactic hoses to remove pull 3 tubes out and instol new part last then 15 min. Making shure is no leaks. Easy
13 of 15 people found this instruction helpful.
Was this instruction helpful to you?
Emile from Oceanside, CA
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Pliers
Parts Used:
WP67006531
Water would not dispense
First turned off the water at the valve. Next I undid the 5 screws holding the plate that holds the pump. Next disconnected the power connectors, then the water lines. Next undid the screw holding the pump, removed pump. Next, mounted the new pump to the plate, this was tricky because it has to fit kind of upside down, so you have to wrangle it into the proper position then align the screw hole. Next, secured it to the plate with the screw, re-connected the water lines, then the power. Before mounting it back to the fridge, I tested to see if it worked, well, it didn't. My heart sank. I re-checked all connections, I redid the entire process, disconnected and re-connected and still did not work. I researched the problem online and someone posted maybe the water filter might be clogged or defective. So I removed the water filter and put the stop plug in, and it worked perfectly. I went and exchanged the filter and plugged it in and still had the same problem. I am now suspecting the filter receptacle is the fault, but we will do without that for the time being. But the pressure is much better so changing the pump was still necessary. All in all a very interesting repair. I learned a lot about how the system works and now I need to replace the damper, it is very noisy.
11 of 13 people found this instruction helpful.
Was this instruction helpful to you?
Michael E from Green Bay, WI
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Socket set, Wrench (Adjustable)
Parts Used:
WP67006531
Inlet valve was leaking water...
Took the valve off from the back of the frig and reinstalled the part I purchased from Part Select. The part was an exact OEM part, not a substitute that others had. The install went very smooth and once again we have water and ice from our frig. Can't thank Part Select enough for the thier sales team and the order department. They made sure that I got the exact part that I needed. Customer for life.... Mike D. Wisconsin
8 of 11 people found this instruction helpful.
Was this instruction helpful to you?
Charles from FISHERS, IN
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
Parts Used:
WP67006531
froze and cracked
unsrewed the back plate, removed three tubes. Then I removed old valve and replaced with new. Pluged two harnesses back in the new valve. Truned water on and checked for leaks and operated the filtered water tap and the ice maker. All went well.
I really like your site for the pictures included with the part, I like to see what I'm ordering.
6 of 8 people found this instruction helpful.
Was this instruction helpful to you?
Julie from HOOVER, AL
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Socket set, Wrench (Adjustable)
Parts Used:
WP67006531
The duel water valve began leaking
Plumber came to stop the water leak and told us it was a bad valve so I ordered the part - thank you Kate! - it was exactly what we needed. Disconnected the old valve (making note on the process) and installed the new valve in reverse process. Turned the water on and dispensed water and it leaked from one of the lines at connection. With the water turned off, my son again with pliers carefully pushed the tubing harder up into the valve and heard/felt it click into place and it has worked like a charm since. Good son and mom team.
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Victor R. from BROOKLYN, NY
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver
Parts Used:
WP67006531
Stead flow of water from under the refrigerator
Unplugged and disconnected the water supply.Disconnected the water line coming from the filter and cut about 1/8 inch off to square it off.
Unscrewed panel to expose inlet valve. With a marker I noted where the lines need to go back to. Disconnected the other two lines and made fresh straight cuts with a utility knife. Disconnected both plugs from the old inlet. The yellow one was difficult to get off, so I carefuly used a screw driver. Be careful, you don't want to break the plug. Reinstalled the new inlet. make sure that you push all of the lines in the valve so that they are completely seated. Make electrical connections. Secure valve to the panel. The water line from the filter should be the last line that you connect. Put screws back in the panel.
Plug in and turn on water supply. Fill up a gallon container from water dispenser. Check for leaks. Let the ice machine fill up. Check for leaks. Place back panel back on and secure. GOOD LUCK!
1 person found this instruction helpful.
Was this instruction helpful to you?
Julie from KIRKERSVILLE, OH
Difficulty Level:
A Bit Difficult
Total Repair Time:
More than 2 hours
Tools:
Nutdriver, Pliers, Wrench (Adjustable)
Parts Used:
WP67006531
No water getting to Ice Maker
Cleaned all lines running to water control valve and ice maker. Replaced water control valve still no water to Ice Maker. Replaced Ice Maker as tec. support suggested. Still no water to Ice Maker talked again to tec. support they didn't know what to do? After I spent 200.00 dollars in parts and shipping. NOW I still have get a repairman out fix the problem. The program is helpful but I don't see why you don't have someone to talk to about the problem that knows what they are talking about. It may be a defective waters inlet valve that you sent. The Ice maker does work if it had water. I ran a test with the jumper wire as suggested.
1 person found this instruction helpful.
Was this instruction helpful to you?
John from CORNELIUS, NC
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers
Parts Used:
WPW10137519, WP67006531
The fill tube was freezing up after about 60 days of use.
Pulled the unit from the wall, and unplugged, and turned off the water. Removed the back plate at the bottom of the refrigerator to gain access to the water inlet valve. Disconnected three tubes and two electrical connections and reconnected to the new inlet valve. Reassembled the back plate. Then turned everything back on and checked for leaks. Re-Installed the back plate. This was a fairly easy repair. The only problem I had was getting the water lines off the old valve. It was a bit of a struggle for me. I did watch a couple of you tube videos before I got started.
1 person found this instruction helpful.
Was this instruction helpful to you?
Customer Reviews
Average Rating:
10 Reviews
4.6
out of 5
Filter By Rating:
  • 5 Stars
    8
  • 4 Stars
    1
  • 3 Stars
    0
  • 2 Stars
    1
  • 1 Stars
    0
Sort by:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
5
-
Verified Purchase
Easy repair, great part - worked as expected

Got the part very quickly. Followed the top installation instruction, worked like a charm. My fridge no longer leaks!

5
-
Verified Purchase
Easy repair

Part was exactly same as the one being replaced. Make sure you get the right one according to your model number.

5
-
Verified Purchase
Frozen Inlet Valve

I had left a refrigerator out in my garage and forgot about draining the water out of the lines. In Minnesota it gets cold in the winter and yes the Water Inlet Valve froze and cracked. I went on line and found PartSelect. They made it easy to find the part I needed. I ordered it and received it within days. Thank You

5
-
Verified Purchase
Easy repair

The part was identical to the original part and the replacement was done in about an hour. As I took the hoses out of the old part, I would place them into the new part. Once all hoses were in place, I turned the water back on to verify there were no leaks. Part has been in service for last week with no issues.

5
-
Verified Purchase
Simple and easy to install

Turn water off first! Have a bowl or big cup to catch water backflowing from the tubes. When pushing the tubing into the part, be sure you have the right tube going to the right hole and push it in with significant pressure until you hear/feel in click in and push a bit more. Once clicked in, tubing won’t come out! A 15-20 minute install

5
-
Verified Purchase
Fixed the fridge leak as expected

Had a major leak, flooding the kitchen and this part fixed it well. Ice maker & drinking water work fine now, yay!

5
-
Verified Purchase
great experiance

The Parts Select experience was great! The website helped me pick the correct part to fix my leaking fridge. It arrived quickly, and the installation was not bad at all.

5
-
Verified Purchase
Icemaker repair

The part was identical in form and function to the original and worked perfectly. The problem was that the original valve did not close completely after letting water into the ice trays. The continual drip froze all the cubes into one block and eventually clogged the flow tube. New valve solved the problem. Plenty of twice cubes.

4
-
Verified Purchase
Easy repair, just make sure tubes are inserted fully

After memorizing what the connections looked like, everything went back together fine, except you need to her careful that you insert the plastic tubing fully into the receptacle holes. One of them was not in all the way, and a vicious leak developed when I first cut the water back on. But after applying a little plumber's grease around the tube end, I got it to go completely in. Now it works great.

2
-
Verified Purchase
Water value for fridge

Part works great. Partselect sales person upgraded shipping to get 10 bucks more out of you but didn't get it me any faster then ground. Poor customer service.

Model Cross Reference

This part works with the following models:

PartSelect Number: PS11743697
Manufacturer Part Number: WP67006531
Brand
Model Number
Description
Kenmore
59657012600
Refrigerator
Kenmore
59657013600
Refrigerator
Kenmore
59657016600
Refrigerator
Kenmore
59657019600
Refrigerator
Kenmore
59657043600
Refrigerator
Kenmore
59657049600
Refrigerator
Kenmore
59657053600
Refrigerator
Kenmore
59657059600
Refrigerator
Kenmore
59668942800
Refrigerator
Kenmore
59668943800
Refrigerator
Kenmore
59668949800
Refrigerator
Kenmore
59676592600
Refrigerator
Kenmore
59676592601
Refrigerator
Kenmore
59676592701
Refrigerator
Kenmore
59676593600
Refrigerator
Kenmore
59676593601
Refrigerator
Kenmore
59676593602
Refrigerator
Kenmore
59676593702
Refrigerator
Kenmore
59676594600
Refrigerator
Kenmore
59676594601
Refrigerator
Kenmore
59676594701
Refrigerator
Kenmore
59676599600
Refrigerator
Kenmore
59676599601
Refrigerator
Kenmore
59676599701
Refrigerator
Kenmore
59676602600
Refrigerator
Kenmore
59676602601
Refrigerator
Kenmore
59676602701
Refrigerator
Kenmore
59676603600
Refrigerator
Kenmore
59676603601
Refrigerator
Kenmore
59676603702
Refrigerator

All brand logos are trademarks of their respective owners.

The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.

Copyright © 1999-2019, Eldis Group Partnership. All rights reserved.