Ask our experts a question about this part and we'll get back to you as soon as possible!
6 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Jim
March 23, 2018
The dryer was making loud rumbling noise. Have front of dryer apart. Rollers, belt, etc. Appear fine however the motor is loose. On the rear shaft where it goes through a hole you can see where a plastic fitting has been damaged from hitting the opening. Motor shot or something else? Have not opened back of dryer yet.
For model number RGD4640YQ2
Hi Jim,
Thank you for your question. I would suggest maybe just taking a look at your motor bracket. Take a look to see if maybe it is loose or broken. It may be your motor that is the issue. The part that is broken sounds like your pulley. That might be the reason you are getting the rumbling. I hope that helps. Good luck with your repair.
1 person found this helpful.
Was this helpful?
Thank you for voting!
Barry
November 11, 2021
Originally dryer over heater and tripped the thermal link. Ordered and replaced part. Tripped 2nd thermal. Hardly any air through duct. Cleaned duct. Replaced thermal #3. Min to no air and shut it down. What moves the air...motor, fan? Or could something have it tripped?
For model number WED4815EW1
Hello Barry, thank you for your question. It is the blower wheel attached to the motor that pulls the air into the dryer, through the lint trap, and out of the vent. There could be a build up of lint inside the dryer impeding the flow of air, or the motor could be failing. Part number PS334304. We hope this helps.
My wash machine started making a clicking sound. It was filling with water, the clothes were washing, the water would drain, and then it wouldn't go to the spin cycle. That's when the clicking started.We unplugged it and plugged it back in and now when you push to start the wash machine it only makes a clicking sound. could this be the motor or the circuit breaker?
For model number NGD4655EW2
Hello Kitty and thank you for writing.
It certainly sounds more like a faulty cycling thermostat PS11741405 you should check for signs of damage, and replace it if needed. If this does not fix this problem then your drive motor PS334304 might be faulty. We hope this helps. Please contact us anytime.
Dryer heats but drum won’t turn. Belt is good. Not sure if drive motor is bad or something else
For model number MEDC200XW1
Hello Tim, Thank you for contacting us. We have researched the model you have provided and have found
the part you are looking for is the Door Switch PartSelect Number PS11741701. If it breaks or is defective, you won't be able to start or stop your drying cycle, depending on the position your switch broke in. The easiest way to test this part for functionality is to test it by hand. Push on the black tab that sticks out of the front panel to make contact with your dryer door; if there is no resistance in the tab and it doesn't make a click sound, you may need to replace it. We hgoe this helps!
The dryer runs for approximately 5 sec. Then shuts off. What could possibly be the?
For model number NED4655EW1
Hello Paula, thank you for contacting us. Make sure your dryer vent is not blocked. Blocked ventilation also causes this problem. If the dryer vent is not blocked then the problem can be caused by a faulty dryer thermostat. You may need to replace the dryer thermostat, part number PS11741405. We hope this helps.
Hi Jerome, Thank you for the question. The Push to Start Knob is Part #: PS11752709 and the Switch behind the knob is Part #: PS11741680. We hope this helps!
