Quick Question!

Have you ever purchased from PartSelect.com before?

11741460-1-S-Whirlpool-WP3392519-Thermal Fuse
11741460-1-S-Whirlpool-WP3392519-Thermal Fuse 11741460-2-S-Whirlpool-WP3392519-Thermal Fuse 11741460-3-S-Whirlpool-WP3392519-Thermal Fuse https://www.partselect.com/Schematics/Whirlpool/SNBNEJXS.gif

Thermal Fuse

Your Price

$8.98
Get this part fast. Average delivery time via standard shipping: 1.8 days.

PartSelect Number PS11741460
Manufacturer Part Number WP3392519
Manufactured by Whirlpool

This thermal fuse is designed for use in dryers. It is a safety mechanism that stops the flow of electricity to the heating element when a dryer overheats. When this fuse is faulty, your dryer will not start or it will not heat properly. This is a one-time fuse, meaning it cannot be re-set. It must be replaced when there is no longer continuity between the terminals. This replacement part features two 3/16 inch terminals, and is sold individually. It attaches to the blower wheel housing. Blown fuses can be caused by clogged dryer vents. We recommend checking to make sure all of the vents are clear when you perform this repair.

This part works with the following brands: Whirlpool, Kenmore, KitchenAid, Roper, Estate, Crosley, Inglis, Maytag, Amana, Admiral, Magic Chef.

This part works with the following products: Dryer, Washer Dryer Combo.

This part fixes the following symptoms:

  • No heat or not enough heat.
  • Will Not Start.
  • Takes too long to dry.
  • Shuts off too soon.
  • Timer will not advance.
  • Will not tumble.
  • Too hot.
  • Will not shut off.
  • Touchpad does not respond.

Videos For installing this part.

Questions & Answers

Ask our experts a question on this part and we'll respond as soon as we can.

Most Helpful

Question:

I tried to turn my dryer on today and it wouldn’t budge. When I opened the door the lights wouldn’t turn on and there aren’t any lights on the control panel. It’s plugged in and I didn’t trip any breakers. Do you think it’s the thermal fuse or thermostat?

Justin
Answer:

Hello Justin, thanks for getting in touch. This sounds like it is the thermal fuse WP3392519, but before replacing it you should inspect and test it for visible damage or indication of faultiness. If the thermal fuse is open and not working, your next check should be the exhaust ducting, since it is the most common reason for a thermal fuse to malfunction. Please let us know if you have further questions.

13 people found this helpful.
Question:

How do i check the thermal fuse

Sandi
Answer:

Hi Sandi, That's a great question, you can use an multi meter and test the continuity of the fuse.If no current is detected, it means there's no continuity and the fuse is defective. Good luck with this repair.

7 people found this helpful.
Question:

The dryer died mid cycle and I haven’t been able to turn it on since. I just can’t figure out what is happening. I already changed the thermal fuse, and it still isn’t starting. What should I look for next? And yes it does have power.

Bradley
Answer:

Hi Bradley, thanks for getting in touch. If you already replaced your thermal fuse and that has not fixed the problem, check your door switch to see if it is faulty. I hope this helps!

5 people found this helpful.
Question:

This dryer has an end of cycle signal that buzzes when the dryer time has ended. It stopped functioning a couple of weeks ago and i could not find a part online that fixes that function. The closest one i can find is the thermal fuse. Is that the likely culprit or is there another one i should suspect?

Janice for model number cabrio dryer WED62005w1
Answer:

Hello Janice, thank you for getting in touch. The buzzer is located in the main control board for the dryer. You would need to replace the whole control board in order to replace the buzzer. Control board, part number: PS11746535 $211.87 Hope this helps!

4 people found this helpful.
Question:

This is the third time in the past seven months that my dryer has blown a thermal fuse. The first time I didn’t think anything of it but after the third time I think there has to be something wrong. I clean out the lint trap every time… what should I check next?

Alison
Answer:

Hi Alison, although there are a few causes to this issue, the most common one is the exhaust ducting. If there is too much heat trapped inside the ducting it will cause the thermal fuse to open. What you need to find is any air flow problems. Is there breakage or clogging in your duct? Is it too long? The next thing to check would be if the ducting has condensation or water in it, or if there are dryer sheets in the blower wheel. Lastly you can check the drum seal to see if it is malfunctioning. Best of luck!

3 people found this helpful.
Question:

Where to find and how to replace thermal cutoff

Krtystyna for model number LGR8648PQ0
Answer:

Hi Krystyna, Thank you for your inquiry. The thermal cut off is found near the duct assembly. Before attempting the repair, unplug your appliance and then remove the back panel. Next disconnect the old jumper wire and remove the mounting screw and slide the old cut-off fuse out of the slot. Disconnect the wire, and install the new cut-off fuse by securing it with the mounting screws and reconnect the wire. Now remove the mounting screws to detach the old high limit thermostat. Remove the wire and install the new thermostat by aligning it in place and reattach it with the mounting screws. Reconnect the wire and then connect the fuse and the thermostat with the new jumper wire and put the back panel back on the appliance. Plug the appliance back in to see if it is working correctly. I hope this helps. Thank you and have a great day!

3 people found this helpful.
Question:

I can't find a part called a thermistor. Tech sheet calls it that.

Lonnie for model number Gew9200lwi
Answer:

Hi Lonnie, Thank you for the question. The thermistor is also called the Internal-Bias Thermostat . PartSelect Number PS11746740. Hope this helps!

Related Parts: Thermostat
3 people found this helpful.
Question:

How to know, if i need the whole thermos kit? Or only the thermos fuze?

susan for model number LER4634JQ1
Answer:

Hi Susan, Thank you for your inquiry. To verify which part is causing the issue you will need to use a multimeter to check the continuity of each part. I hope this helps. Thank you and have a great day!

3 people found this helpful.
Question:

Dryer stopped heating. Everything else works.

Richard for model number 11074832400
Answer:

Hello Richard, thank you for contacting us. If you are getting no heat but everything comes on, it could be one of the thermostats or the heating element. Usually the thermostats will go bad first, you can test these with a multimeter. Hope this helps!

2 people found this helpful.
Question:

Where is the thermal fuse located

Pete for model number WED9750WW0
Answer:

Hi Pete, That's a great question. The thermal fuse is located on the blower fan housing. To get to that part you will need a few tools: a hex socket, a putty knife, a flat head screwdriver, and also a phillips screwdriver. Please make sure to disconnect power to your appliance before ever attempting any repair. First you will want to remove the top panel screws. Place your top panel safely out of the way. Then take a look at your control panel. Press in the tabs on either side to pop it out of place. Disconnect the wire harness and then remove the screws to be able to move your circuit board bracket out of the way. Then remove the screws on the control bracket up front. Now you will want to remove the screws from the lower panel at the bottom of your machine. You can just lift that part right out. After that you will want to disconnect the moisture sensor and door switch wire harnesses. One set of wires should be yellow while the other set are brown, white, and blue. Then you will want to remove the screws at the bottom and top of your front panel. There are two mounting screws on the inside of your door panel. There are on either side of the filter. Remove those as well to be able to pull off the front panel. You will then remove the lower bulkhead screws and only loose the top screws. Don't take those ones off fully. Also remove the screw holding the blower housing in place as well. Then lift the bulkhead off the top screws and set it aside. After that you will remove the dryer belt from the motor pulley and pulley. I would suggest taking a picture of how the belt is installed on your appliance. So that you can reinstall it the same way. Use the belt to help you lift out the drum. Now you will have access to the thermal fuse inside of your machine. You can remove that part by unplugging it and removing the screw. To get your drum back into place, align its rim with the two rear rollers. Then follows these steps backwards and you will be able to put your machine b

2 people found this helpful.
Question:

My dryer cooking my clothes. I even test the air only and the dryer was still extremely warm. Thermostat? Fuse? Help

Greg for model number WED9050XW1
Answer:

Hi Greg, Thank you for the question, I suggest you replace the Thermostat, Internal-Bias, This part controls the temperature of the inside of the dryer drum and prevents the dryer from overheating. We also suggest you replace the Thermal Fuse, It is a safety mechanism that stops the flow of electricity to the heating element when a dryer overheats. When this fuse is faulty, your dryer will not start or it will not heat properly(too hot) and if the thermostat is defective it can trip the fuse. Good luck with the repair!

Related Parts: Thermostat
1 person found this helpful.
Question:

My dryer works just does heat up thinking thermal fuse thanks

Dave for model number LEQ9858PW1
Answer:

Hi Dave, Thank you for your inquiry. If your dryer is not heating the most common parts to fix the issue are the heating element, the thermal fuse, the thermal cut-off kit, the high limit thermostat, the heating element connection wire kit and the internal bias thermostat to name a few. To verify which part is causing the issue, you will need a multimeter. I hope this helps. Thank you and have a great day!

1 person found this helpful.
Question:

Does it matter which blue wire goes on which tab on the thermal fuse? My Whirlpool dryer has a blue wire coming from the top wiring harness and one coming from the bottom.

John
Answer:

Hi John, Thank you for your inquiry. There is a video on our website just under the information on the fuse that you can reference on how to install it. I hope this helps. Thank you and have a great day!

1 person found this helpful.
Question:

Can the termal fuse cause the dryer to stop in the middle of the cycle and not start again?

Tim for model number LGQ9858LW0
Answer:

Hi Tim, Thank you for your question. Yes it can. Sometimes it can also be your door switch or m series coils as well. I would suggest testing all three of those parts with a multimeter to see if they are working correctly. Good luck with your repair.

1 person found this helpful.
Question:

I need directions (video) how to get in the dryer. You can't just take screws out of back to remove back. The back goes up under the top, how do i remove top???

Jackie for model number GEQ8831LL0 Whirlpool Gold
Answer:

Hi Jackie, Thank you for your question. This part actually has an installation video underneath the part information. Here is the URL: https://youtu.be/ajDWK7x1J5Q . Good luck with your repair.

1 person found this helpful.
Question:

Hello! My dryer turns on but will not heat. I have disassembled the rear end and cleaned the ducting from the heating coils to the dryer. I have also removed the toe plate and tested continuity from the red wire terminals on the heater element to the red wire terminals on the thermal cut off and i'm getting about 9.5-10 olms.I have inspected all wire terminals and they look good. The technician manual directs me to test the continuity at p14-3 and p14-6 at the control head. I'm not getting any resistance and the manual says to replace the thermistor. Am i on the right track?

Brendan for model number WED9151YW0
Answer:

Hi Brenden, Thank you for your inquiry. Yes it does sound like it is the thermistor that may be the issue. I hope this helps. Thank you and have a great day!

1 person found this helpful.
Question:

My dryer will start drying the clothes, but then after a few minutes, the heating stops. All the controls work - but the dryer seems to be only blowing room temperature air. I have cleaned the duct inside the dryer, and through the duct from the dryer to outside. I read that if the fuse was blown that the dryer would not start. Except for lack of heat throughout the cycle, the dryer thinks it is working just fine. What is my next step?

Vickie for model number GGW9250PW1
Answer:

Hi Vickie, Thank you for the question. Normally with the Thermal Fuse the dryer would still run as normally but there will be no heat. So you would still have the appliance start and tumble but blow cold or room temperature air. If the fuse blows it just stops electricity going to the element its self not the appliance. Hope this helps!

1 person found this helpful.
Question:

Does this thermal fuse go on a Inglis model gas dryer? Symptoms are no heat and the dryer keeps running. Thank you.

Shane for model number igd4300sq0
Answer:

Hi Shane , Thank you for the question. Yes this is the correct Thermal Fuse for your model number. This is the most common part replaced when you are not getting heat. Hope this helps!

1 person found this helpful.

Most Recent

Question:

My dryer is not heating but still runs. Checked the thermal fuse and its not that.What else could it be?

MARGARET for model number MEDX700XW0
Answer:

Hi Margaret, Thank you for the question. If the Thermal Fuse has tested to be good, I suggest checking the High Limit Thermostat,PartSelect Number PS11741456.This hi-limit thermostat acts as as safety mechanism that keeps the dryer from overheating. Once the dryer temperature reaches a certain point, this piece will shut down power to the heating element. When defective it will not send power to the element in order for it to heat up to dry the clothes. Hope this helps!

1 person found this helpful.
Question:

The dryer makes a beeping noise when start button pushed and will not run.

Mike for model number WGD9500TW2
Answer:

Hi Mike, Thank you for the question. Normally if the dryer just beeps when you press start it is one of two things. The door is not closed fully and the most common is a faulty Thermal Fuse,PartSelect Number PS11741460. If your door is closed then I suggest replacing the fuse. Hope this helps!

1 person found this helpful.
Question:

My air fluff dry cycle does not work at all. What could the problem be.

Janet for model number WED5200VQ
Answer:

Hi Janet, Thank you for the question. Soudns like you need to replace the Timer,PartSelect Number PS11742197.This dryer timer is used to control the unit's cycles. Hope this helps!

Related Parts: Timer
Question:

The igniter will not glow,I replaced the igniter and thermal fuse,still no glow

Mac for model number WGD9200SQ1
Answer:

Hi Mac, Thank you for the question. When the igniter will not ignite it is recommended you replace the M' Series New Style Coil Kit. Hope this helps!

Question:

Hello- my dryer is about 10 years old. About 1-2 years ago, I noticed the clothes were no longer drying on the "normal" setting. I started using the "jeans" setting, which seems to increase the heat from medium to medium-high as well as extends the time. The clothes always dry on this setting, but I am wondering if I am losing $$ on running the unit longer. The unit seems to heat, but I need the longer cycle to dry the clothes. Any suggestions as to the cause? Thanks.

Marc for model number 110.85862401
Answer:

Hi Marc, Thank you for the question. I suggest trying to replace the Sensor,PartSelect Number PS11741408. When the appliance takes to long to dry or is not giving off enough heat to dry in its set time or cycle, the sensor normally needs to be replaced. Hope this helps!

Question:

I received the thermal fuse. Replaced that part and plugged back in and ran dryer without assembling back panel. Just to see if the dryer would heat, before i closed up shop. However, no heat still. So, next step?

Susan for model number ler4634jq1
Answer:

Hi Susan, Thank you for your question. I would suggest testing your thermostats to see if they are all functioning properly. If they are I would also suggesting testing your heating element and door switch as well. I hope that helps. Good luck with your repair.

Question:

Does this thermal fuse work in my Maytag?

Teresa for model number Ldg9034aae
Answer:

Hi Teresa, Thank you for your question. No, I have linked the correct fuse for your appliance in a link down below. Good luck with your repair.

Related Parts: Thermal Fuse (Limit: 183)
Question:

I think i need a new control panel for a Whirlpool duet dryer. Digital message f01 on display and dryer will not start. A clicking sound from the black box on upper left corner of the control panel. Thank you

John for model number WED9400SW2
Answer:

Hi John, Thank you for your inquiry. The F01 error code indicates a possible failure of the electronic control board. It may be caused by a glitch or a power surge. Try to unplug the dryer for 5 minutes and if this does not help you may have to replace the electronic control board. I hope this helps. Thank you and have a great day!

Question:

Where is the thermal fuse located? Are there visual available?

Jim for model number 11070832990
Answer:

Hi Jim,Thank you for the question.The thermal fuse attaches to the blower wheel housing. If you enter in the part number there is a diagram associated with the part and it shows where it is located.Good luck with the repair!

Question:

My dryer wasn't working recently and discovered that the thermal fuse went bad. I replaced it and now it starts and heats up, but it gets really hot even in "air dry only" mode. I checked and the events and cleaned them out good, could it be a the thermostat? I read that it could be a shorted out heating element.

Shaun for model number WED9600TW1
Answer:

Hi Shaun, Thank you for your inquiry. That would not be out of the realm of possibilities. I would suggest testing your bias thermostat and the element with a multi-meter to see which one is giving you the issue. The bias thermostat measures the temperature inside your drum, it may have shorted when the thermal fuse stopped working. Good luck!

Question:

Dryer died mid cycle, now it won't start. Dryer still ticks, checked the push button start and that was fine. Door switch turns light on and off when i hold it down. Would it be the thermal fuse?

James for model number WED5540SQ0
Answer:

Hi James, Thank you for your question. The thermal fuse is one of the main reasons why this would happen, but you should still check the other two parts as well. Even though they may seem like they are working, there could be a component that is not working and thus will not let your appliance start. You can check all three of these parts with a multi-meter to make sure. Good luck with your repair!

Question:

My dryer won't start.

Aki lena for model number WED5300SQ0
Answer:

Hello Aki, thank you for contacting us. The most common part for this would be the thermal fuse, when this goes the dryer will not start at all. You can test this part with a multi-meter. Hope this helps!

Question:

My dryer will not heat if i have it on timed drying. It did work on automatic drying selection but not anymore..every once in a while after its been sitting not used...i can turn it on using the automatic cycle again and it will try once but not again if i keep starting it over....i have even checked the lint screen and disconnected the ventilation ducting..help

James for model number WED5100VQ1
Answer:

Hello James, thank you for contacting us. It is possible that one of the thermostats is faulty giving bad readings to the control board. These can cause the dryer to not produce any heat or very little. Also it could be the heating element, these can be tested with a multi-meter to determine which is at fault. Hope this helps!

Question:

The cycle signal does not work. Dryer stops but signal does not work

Donna for model number 110.66002010
Answer:

Hi Donna, Thank you for your question. Sometimes unplugging the appliance for about five minutes and then plugging it back in will reset your appliance and the buzzer will continue to work. However a technician is normally required to verify which part is actually causing your issue, as there are multiple tests that they would have to perform on your appliance. I hope this helps. Good luck with your repair.

Question:

Water leaking in dryer what is the fix?

Jerry for model number Wed9270xw0
Answer:

Hi Jerry, Thank you for your inquiry. If there is water leaking in your dryer, you may need to check the water inlet valve, the hoses and where the hoses are connected to, to see if you can find the leak. I hope this helps. Thank you and have a great day!

Question:

My dryer, I put the time on 60 minutes and the heater works, but if I put the timer on 40min or lower I get no heat.

Algenis for model number RED4640YQ1
Answer:

Hello Algenis, thank you for contacting us. It's possible that one of the thermostats could be faulty or the heating element itself. These can be tested with a multi-meter. Hope this helps!

Question:

My dry will cut on, and work for about 10 minutes, and then shut off. I'll have to wait about 10 more minutes to cut it back on for it to work again. I'll have to continue doing this until my clothes are dry. Will this fix my dry?

Teresa for model number WED6200SW1
Answer:

Hi Teresa, Thank you for your inquiry. It is likely that this part might be causing your problem. I would suggest testing this part and your door switch with a multi-meter to see which part is malfunctioning. Good luck!

Question:

Hi, my dryer has been taking longer to start when holding down the start button & now wont start at all and is making weird beeping sounds and the lights are going off through the selections. Do u have an idea of what i need to replace? Thank u!

Kim for model number WED9050XW1
Answer:

Hi Kim, Thank you for your inquiry. The thermal fuse usually fixes the issue 78% of time, but some other parts you may have to look at are the door catch kit, the internal bias thermostat, the drive belt, the idler pulIey, the drive motor and the drive belt to name a few. To see if the electrical parts will fix the issue you will need a multimeter. I hope this helps. Thank you and have a great day!

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.9 / 5.0, 328 reviews What's this?
 

3 of 3 people found this instruction helpful

Parts Used:
  • Thermal Fuse
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers, Socket set
Customer: MONA from SHAMROCK, TX

Dryer would not start.

I watched the video or I would have likley just called a repair man. It took longer to clean behind the dryer than to install the new thermal fuse. After taking the back off the dryer is was as simple as changing a fuse. Dryer works like new for about $20 bucks and we avoided the hasle of getting a repair man, especially since we live in the country. Thanks for having a web site that is so easy to use and full of good information.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

3 of 3 people found this instruction helpful

Parts Used:
  • Thermal Fuse
Level of Difficulty: Really Easy
Time to do repair: 1- 2 hours
Tools: Nutdriver, Screw drivers
Customer: Chris from st louis, MO

Dryer wasnt heating up, though it would run

Removed the dryer's back panel and took a look. Had no idea what to do next, so I read up on it. Partselect was extremely helpful to me, the exploded views with the part numbers called out were particularly helpful. So I determined it was the thermal fuse. Unscrewed the screw holding in the fuse and disconnected the electrical supply. New fuse went in really easily. Job took a lot longer than it had to cause since I was in there, I cleaned out the dryer really good.

Why the fuse blew was interesting: had an extension cord routed over the dryer, well it was situated such that it caused the timer knob to bind up. Apparently, the dryer ran all night because of this and blew the fuse. So don't obstruct the knob or you will be replacing a thermal fuse!

Help other customers find the most helpful instructions.

Were these instructions helpful?   

3 of 4 people found this instruction helpful

Parts Used:
  • Thermal Fuse
Level of Difficulty: A Bit Difficult
Time to do repair: 30 - 60 mins
Tools: Screw drivers, Socket set
Customer: Timothy from Anderson, IN

Dryer would not start / failed to run.

My dryer would not start or turn. I first moved the timer to midway between start and end of a cycle and could hear the timer ticking, likely eliminating the timer as the culprit. I next opened the door, manually pressed the door-closure switch and pressed START to see if the heating coil was heating without the drum turning to see if it might be a motor issue. After no heat, I unplugged the dryer and removed the vent hose by loosening the clamp and then removed the lower back cover using a socket and ratchet. Using a multimeter, I quickly found an open thermal fuse. I tested the remaining components to see if they also required replacement (coil, thermostat, high temp sensor) - all tested good. Took a chance and ordered the fuse alone instead of also purchasing replacement thermostat as many advise - if you have not replaced in a while, probably worth doing now. I have replaced mine within a year or two and chalked up the issue to my kids not clearing the vent, so I went without the new thermostat. Model number was found by opening the lid - parts arrived incredibly fast especially for being around the holidays. Replaced the fuse with ease - there is a notch in one end that holds the non-screw end in place so it's flush. Plugged the dryer back in, selected a cycle and confirmed the dryer started and heated as normal. I then had my son open the dryer door to confirm the drum stopped turning. HERE'S WHERE IT TAKES A TWIST: When the door was open, the heating coil continued to glow red hot (faulty timer??) I moved selector to end of cycle and the glow stopped. (timer's good) I then moved the selector mid-way between cycles with the dryer door open and WITHOUT PRESSING START and the coil again glowed red. Disconnected power, disconnected coil and using multimeter, checked from coil input to case ground (any bare metal) and found one side of the coil to be grounded. I was able to removed the heating coil and locate where the coil was touching the case. I shifted the coil back into place, checked with meter (no ground this time), reinstalled and tested with no problems. Reinstalled the back plate and vent hose. Finally, had conversation with the kiddos about being gentle when moving the dryer and all was well. The thermal fuse portion took 15 minutes from diagnosis to replacement. The overall process (due to the additional grounded heating coil) took 30-60. With any repair like this, I usually recommend visually verifying the heat cycles on and off by carefully running with the door open and holding the switch. This will help you determine if you may have an additional faulty part that made the first one fail. (Most likely, thermostat).

Help other customers find the most helpful instructions.

Were these instructions helpful?   

4 of 7 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver
Customer: Miguel from Watsonville, CA

Working but no heat.

Just removed the back panel with nut driver . Located the parts and replaced one at a t-ime. I replaced all the parts that I order , so I really can't say which part fixed it. But working good now.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

4 of 7 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Wrench set
Customer: Brownell from Clayton, NM

Dryer would not turn on

I am really not sure because my husband did the repair and it took him no time at all. I know he removed the back panel on the dryer, and the 2 parts were in plain site. He took the old off put on the new part. We turned the dryer on and it worked better than ever! This site is the best for home repairs. My husband was a little leary but we didn't want to buy a new dryer and we live in a remote area with no repair people, so for the low cost of these parts it was well worth it! Will diffently use this site again!!!!!!!!!!

Help other customers find the most helpful instructions.

Were these instructions helpful?   

3 of 4 people found this instruction helpful

Parts Used:
  • Thermal Fuse
Level of Difficulty: Easy
Time to do repair: Less than 15 mins
Tools: Nutdriver
Customer: Wayne from Winthrop, NY

Dryer would not operate

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Performed current check to determine possible problem-then Able to go on line with partselect, extremely easy part description and selection, ordered, part arrived next day. Could not have went any better

Help other customers find the most helpful instructions.

Were these instructions helpful?   

3 of 4 people found this instruction helpful

Parts Used:
  • Thermal Fuse
Level of Difficulty: A Bit Difficult
Time to do repair: 15 - 30 mins
Tools: Nutdriver, Screw drivers, Socket set
Customer: Mike from New Windsor, MD

Dryer did not start.

Removed Back and found schematic. Found fuses on schamatic and parts inside dryer. Checked fuses and thermal fuses with an ohm meter and found one that was open. Went to Parts select and ordered part. Relpaced the part and dryer works like new.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

2 of 2 people found this instruction helpful

Parts Used:
  • Thermal Fuse
Level of Difficulty: Very Easy
Time to do repair: 30 - 60 mins
Tools: Nutdriver
Customer: JOANNA from FLATONIA, TX

Replacing the gas ignitor

Unplugged stove . Removed floor of oven . Easy . Removed the ignitor ,near back of stove under removed floor . .Left it in place to enable locating where wire came through back of stove . Pulled the stove away from wall . Removed back panel of stove . followed ignitor wire to its plug in position . Returned to the front of stove . Inserted new ignitor wire through back wall of stove . Went behind stove , pulled wire through enough to plug new ignitor into proper position . Put back panel onto stove . Pushed stove back against wall . Went back into oven to screw new ignitor into place . Replaced oven floor panels . Put cooking racks back in . Wife proceeded to bake once again .

Help other customers find the most helpful instructions.

Were these instructions helpful?   

2 of 2 people found this instruction helpful

Parts Used:
  • Thermal Fuse
Level of Difficulty: Really Easy
Time to do repair: 30 - 60 mins
Tools:
Customer: JoAnn from ANTHONY, FL

Had heat, but clothes did not dry.

Unplugged dryer, unscrewed back, and replaced fuse. Easy as 123. Video showed what to do step by step! I am not a handy man, just a woman trying to be money5 smart. Anyone could do this and save on home repairs.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

2 of 2 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: James from LAWRENCEVILLE, GA

Dryer was cutting off before time

I watched the installation video and learned that the installation was a very easy job to do. I followed the instructions and indeed the job was really easy. Requiring only a 1/4" socket and a Phillips tip screwdriver.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

2 of 2 people found this instruction helpful

Parts Used:
Level of Difficulty: Very Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: Edward from POTTSVILLE, PA

Dryer would not turn on

I found the door switch in the upper right of the door opening was broken. This will not allow the dryer to turn on. The switch is held in by two phillips screws.I removed the screws holding it in place. Next open the door where the lint filter is and remove the two screws. Now at the front corners of the dryer on each side you will need to insert at tool to pop the clips.I used a door panel trim tool. Once you pop the clips lift up the top of the dryer. Next unplug the switch and remove it. Install the new switch through the hole install the switch screws drop the top back down and clip it, reinstall the screws at the lint filter. If this was your problem the dryer should turn on. This is a 15 min job!!!

Help other customers find the most helpful instructions.

Were these instructions helpful?   

2 of 2 people found this instruction helpful

Parts Used:
  • Thermal Fuse
Level of Difficulty: Very Easy
Time to do repair: Less than 15 mins
Tools: Nutdriver
Customer: Dennis from Coal Hill, AR

Blown thermal fuse

I first watched the helpful video on website. Un- plugged the dryer. I removed the back cover and tested the thermal fuse with the multi meter. Ordered the replacement part. Replaced the Thermal Fuse, and put the back cover back on. This was a very easy fix! It takes longer to remove the back cover of the dryer than it does to replace the fuse. While I had the back cover I used my air compressor to blow out any lint. This dryer is as good as new now. this site fast shipper, Great website.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

3 of 5 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: 30 - 60 mins
Tools: Nutdriver
Customer: Jennifer from CLINTON, MS

My dryer stopped heating

The repair was really easy and I loved the DIY videos they were great, not many tools needed to do these repairs that was great. The only thing is this didn't solve my issue.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

2 of 2 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: 30 - 60 mins
Tools: Nutdriver, Pliers
Customer: James from COTTONWOOD, CA

The dryer stopped heating

Accessed and removed the rear panel. I replaced the three electrical components with a nut driver and reattached the rear panel. The fix worked, so I have not yet replaced the gas coil sensors at the front of the dryer. The dryer is 19 years old, so the electrical connectors were pretty tight. I used needle nose pliers to pull the connectors free and prevent any damage to the wires. Good Luck.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

2 of 2 people found this instruction helpful

Parts Used:
Level of Difficulty: A Bit Difficult
Time to do repair: 30 - 60 mins
Tools: Pliers, Socket set
Customer: Kemp J from NANUET, NY

The dryer would not blow hot air.

The online heating element replacement instructions were excellent. The back panel of the dryer was removed by unscrewing 9 screws. The difficulty arose in trying to remove the thermostat from the damaged heating element. My thermostat wasn't connected by screws (the thermostat in the online instructions was). It was much easier to follow the online instructions up until the thermostat removal section, and then remove the thermostat by first removing the heating element from the dryer (connected by two screws), and then using the needle head pliers to gently remove the pliable metal prong that holds the thermostat to the heating element. The metal prong is secured near the top of the thermostat. Once the metal prong is removed, use the pliers to carefully remove the prong that connects the thermostat to one of the two prongs at the bottom of the heating element. The thermostat and the flat wiring connected to the thermostat are one piece. The thermostat is connected to the heating element by the pliable metal prong and the delicate flat wiring attached to the bottom of the thermostat. Reattach the thermostat and other wires to the new heating element, reattach the back of the dryer, and your dryer is blowing hot air again. Upon removing the old heating element is was clear it was damaged as the top three rows of heating coils were burnt. I'm on my fifth load of drying since yesterday's repair. Thanks.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

Model Cross Reference

This part works with the following models:

PartSelect Number: PS11741460
Manufacturer Part Number: WP3392519
Brand Model Number Description
Kenmore10688419100Dryer
Kenmore10688419300Dryer
Kenmore110088732791Washer Dryer Combo
Kenmore11060012000Dryer
Kenmore11060012001Dryer
Kenmore11060012002Dryer
Kenmore11060022010Dryer
Kenmore11060172000Dryer
Kenmore11060172001Dryer
Kenmore11060172002Dryer
Kenmore11060202990Dryer
Kenmore11060212990Dryer
Kenmore11060232000Dryer
Kenmore11060232001Dryer
Kenmore11060232002Dryer
Kenmore11060522900Dryer
Kenmore11060602990Dryer
Kenmore11060612990Dryer
Kenmore1106062110Dryer
Kenmore11060622990Dryer
Kenmore11060702990Dryer
Kenmore11060712990Dryer
Kenmore11060722990Dryer
Kenmore11060724990Dryer
Kenmore11060727990Dryer
Kenmore11060802990Dryer
Kenmore11060812990Dryer
Kenmore11060814990Dryer
Kenmore11060817990Dryer
Kenmore11060832990Dryer