This part covers your soap dispenser and is spring loaded.
How Buying OEM Parts Can Save You Time and Money
Part Videos
Replacing your Whirlpool Dishwasher Soap Dispenser Cover
Troubleshooting
This part fixes the following symptoms:
Will not dispense detergent | Door latch failure | Not cleaning dishes properly | Door won’t close
This part works with the following products:
Dishwasher.
Part# WP3378138 replaces these:
AP6008209, 3376404, 3378138, 3385001
Customer Reviews
Average Rating:
★★★★★
★★★★★
1 Review
5.0
Filter By Rating:
5 Stars
1
4 Stars
0
3 Stars
0
2 Stars
0
1 Star
0
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Robert W - August 15, 2020
Verified Purchase
great part
exact fit, saved me from having to purchase another dishwasher!
< Prev
1
Next >
Customer Repair Stories
Average Repair Rating: 3.8 / 5.0, 11 reviews.
What's this?
Sort by:
< Prev
1
2
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Soap Dispenser Lid Gasket Deteriorated & Leaking
I used the screwdriver to pry the old lid off of the horizontal pin upon which it rotates. One must be careful before removing the old lid to note how the return spring is deployed. The short legs on the spring must be in the lip of the lid before you snap the new lid onto the horizontal pin. It was helpful to lubricate the two catches on
... Read more the lid that snap on the pin with some liquid soap before attempting to snap them on the pin. After the lid is snapped into place and the short legs of the coil spring are in the lip of the lid, use needle nose pliers to attach the other end of the coil spring to the pillar where it was before you removed the old lid. There are videos showing how to do this on Youtube. The spring part is a little tricky. The video makes it look a bit easier than it is..
Read less
Frank from AMES, IA
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers
3 of 3 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Not dispensing detergent
Followed instructions as the videos on this page show.
I ordered a dishwasher soap dispenser "lid assembly". When it arrived, it was not an assembly at all but only a lid. I had to reorder a pin and spring, When i finally had every thing, it was an easy repair.
ed from potomac, MD
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
4 of 7 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Inserting Lid Spring
Had to be careful positioning the spring without breaking the hinge pin. Requires a certain amount of patience.
Got the new door and tried to put it on. The door went on very easily. However, there's a spring that opens the door when the main wash cycle comes around. I never did get that spring right. None of the drawings showed the correct position and after an hour of trying to get it to work right, I gave up. The door comes open slightly (b
... Read moreut not because of the spring) when it's time, and the liquid soap runs out due to gravity. But I wouldn't try to use soap powder because the door doesn't come open far enough.
Read less
george from ten mile, TN
Difficulty Level:
Very Difficult
Total Repair Time:
1- 2 hours
Tools:
Screw drivers
5 of 8 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The detergent door won't open fully
Sorry, probably need a spring as the door is fine. While reading other stories about how hard the spring was to get right, I assumed the spring was part of the door assembly. I'll be calling and returnint the part.
i
... Read more'
Read less
Bob from Carlsbad, CA
Difficulty Level:
A Bit Difficult
Total Repair Time:
Less than 15 mins
1 of 4 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Soap Lid Pin Broken
Snap the old lid off, remove the pin & spring & install new Pin & Spring. Very easy. Thanks To Parts Select got the right parts.
Replacing the pin with the spring is a little tricky, it was hard to hold it. And the little plastic pin breaks real easy too, its hard to get the lid to snap in place without breaking the pin.
Ask our experts a question about this part and we'll get back to you as soon as possible!
3 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Macario
December 28, 2017
We have a problem with the soap dispenser. The soap is not coming out. Can you help?
For model number DU929PFGB2
Hello Macario,
Thanks for your question. This could be due to a problem with the lid spring, part number PS11744874, the latch kit, part number PS382922, or the lid, part number PS11741342. There is a kit with all of these parts under PSPS370872 which may be useful for you.
I hope this helps.
My dishwasher lid is fine but the spring does not keep the lid open anymore. How can i fix this?
For model number 665.15992400
Hi Kelly,
Thank you for your question. If the door spring is not keeping the door open, then it will need to be replaced. The part number listed under your model number for the door spring is PS11741354. If you would like to place an order for it, you may order it either online or by calling our customer service line and anyone will be happy to assist you. We hope this helps! If you have any questions, please let us know.
1 person found this helpful.
Was this helpful?
Thank you for voting!
Stephen
February 19, 2019
Regarding the soap dispenser lid before i buy it. What is it that make the soap dispenser lid/cover open when the door is closed and it is latched shut.
For model number 66515701891
Hello Stephen, Than you for contacting us. This is controlled by a few parts. I suggest checking the following parts: PS11746201 Timer, and PS392727 Lower Detergent Dispenser Actuator Assembly. Good luck with your repair!
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
