Pin (Lid Hinge) WP3372028

Mandy from GREENWOOD, SC
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

SOAP DISPENSER DOOR DID NOT CLOSE.

WATCHED THE VIDEO FOR 2 MINUTES. REPLACED THE 3 PARTS IN LESS THAN A MINUTE. THANKS FOR THE VIDEOS.

Other Parts Used:

ROBERT from MAHWAH, NJ
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

3 of 6 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Worn out spring on detergent release box lid

First, examine very carefully how the old spring relates to the detergent release box lid. Note that the top of the spring has a square-end upside down "U" . This rests on a small ledge on the detergent box. Also note that on either end of the spring is a straight extension of the spring wire. These two "legs" must rest on the inside o ... Read more

Read less

Other Parts Used:

HAROLD from FISHERSVILLE, VA
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

85 of 100 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Will not dispense soap

Remove old spring pin, spring, door
Waste of time effort and money didn't change a thing still won't dispense soap to wash dishes

Other Parts Used:

D from Sadieville, KY
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

2 of 9 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

I broke one part trying to install

no tools necessary buy instructions would have brrn helpful

dwight from onaka, SD
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Tools:
Pliers

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Inserting Lid Spring

Had to be careful positioning the spring without breaking the hinge pin. Requires a certain amount of patience.

Other Parts Used:

Emile from Jamaica, NY
Difficulty Level:
A Bit Difficult
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

7 of 13 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Soap Lid Pin Broken

Snap the old lid off, remove the pin & spring & install new Pin & Spring. Very easy. Thanks To Parts Select got the right parts.

Other Parts Used:

Robert from Port Clinton, OH
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers

4 of 12 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

soap lid missing

Replacing the pin with the spring is a little tricky, it was hard to hold it. And the little plastic pin breaks real easy too, its hard to get the lid to snap in place without breaking the pin.

Other Parts Used:

Wheel Assembly

Rinse Aid Cap

Jim from Oktaha, OK
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

8 of 25 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

the pin was broken

but the pin in and add the pin though the 2 tabs close door on it open it up move the springs backwards to the door

Other Parts Used:

Jo-Anne from Columbia, SC
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

7 of 12 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

soap dispenser door/spring broken

removed old parts and re-installed new parts. The spring is a little hard to get to the right point without a jewelers screwdriver, after that everything worked fine.

Other Parts Used:

Dishwasher Door Gasket - Gray