11741267-1-M-Whirlpool-WP3369012-Disk & Mount Assembly
Part Location Diagram of WP3369012 Whirlpool Disk & Mount Assembly
See part 10 in the diagram
( Grid squares measure 1x1 inch )
11741267-1-S-Whirlpool-WP3369012-Disk & Mount Assembly 11741267-2-S-Whirlpool-WP3369012-Disk & Mount Assembly 11741267-3-S-Whirlpool-WP3369012-Disk & Mount Assembly Part Location Diagram of WP3369012 Whirlpool Disk & Mount Assembly
Customer Service Representative

Get in touch, we're here to help!

Daily 8am - 9pm EST

customerservice@partselect.com

Disk & Mount Assembly WP3369012

Rated by 5 customers 

Easy 

1- 2 hours 

Ratings submitted by customers like you who bought this part.

$ 36.46
  In Stock
Get FREE EconoShip on orders over $100! T&C apply

Get this part fast! Average delivery time for in-stock parts via standard shipping: 1.8 days.

PartSelect Number PS11741267
Manufacturer Part Number WP3369012
Manufactured by Whirlpool
Product Description

Disk & Mount Assembly Specifications

Used in the dishwasher pump area.
How Buying OEM Parts Can Save You Time and Money

How Buying OEM Parts Can Save You Time and Money

Troubleshooting
This part fixes the following symptoms:
Leaking
This part works with the following products:
Dishwasher.
This part works with the following products:
Whirlpool, Roper, Kenmore, Estate.
Part# WP3369012 replaces these:
3369012
Back to Top
Customer Repair Stories
 Average Repair Rating: 2.5 / 5.0, 5 reviews. What's this?
Sort by:
  • 1
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Leak from the impeller
Replaced the impeller using the kit. Had to brake the impeller since it was stocked due to rust.
Other Parts Used:
Disk & Mount Assembly IMPELLER
  • Julio from ORLANDO, FL
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Pliers, Screw drivers, Socket set, Wrench (Adjustable)
4 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Pump impeller went crooked, apparently both from wear and moving the unit. Would not then stay in place.
Disconnected hoses (2) from pump housing. Disconnected pump housing from motor (3 allen screws, not too acessible). Unscrew spray arm from pump housing (this is done by hand; no tools as the "nut" is about 3" diameter and made of plastic) Open up the pump casing and replace impeller and the bearings on each side. The thing that takes some time is to mop the water that comes off at almost each step. There is probably an intelligent way to drain everything first. I did not order the large seal (kind of a large rubber donut, larger than a donut) between the arm and the pump and I shoiuld have as it was difficult to keep the old one from not leaking: Since by hand you cannot tighten the large nut very hard and tools could damage or break it. Applying upward pressure on the pump while tightening did it. (The pump and motor are all mounted on flexible mounts, like the heavy hoses connecting to the pump housing, so that there are no vibration.)
Read less
Other Parts Used:
IMPELLER Disk & Mount Assembly
  • Guy from Santa Fe, NM
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    More than 2 hours
  • Tools:
    Nutdriver, Pliers, Screw drivers
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
slow leak at motor/pump interface
Got parts breakdown online, took pump assy apart, ordered new parts, replaced bad parts, put pump assy and dishwasher back together, piece of cake, no problems.
Other Parts Used:
IMPELLER Disk & Mount Assembly
  • Donald from Webster Groves, MO
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Pliers, Screw drivers, Socket set
1 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Pump not working properly
I removed the inner nut holding the spray arm onto the pump. Turned the washer on it's back and removed the wire clip holding rear of the pump motor. Completely removed the pump housingand motor from the washer. Removed three(3) long screws holding the motor to the pump housing. Removed the dish from the housing and removed the old impeller and seals .
Cleaned the pump housing of calcium with lime-a-way. Reinstalled all new parts in reverse order as they order taken off. Cleaned inside of dishwasher with lime-a-away and general purpose cleaner. Reinstall pump housing and motor on washer in reverse order as they were taking off.
Reinstalled washer into cabinet and connected all hoses, drain lines and electrical wired. Turned washer on and watched it run throught a complete cycle. Worked just fine and no leaks. Parts were great.

Sincerely,
James
Read less
Other Parts Used:
IMPELLER Disk & Mount Assembly
  • James from Little River, TX
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
9 of 10 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Leak at the seal
Getting the dishwasher out was easy. Getting to the impeller was easy. Getting the impeller off of the motor shaft was the difficult part. I had to use my Dremel tool with lots of cutoff wheels to cut the impeller off of the motor shaft a little piece at a time. It appeared to be rust on the motor shaft that was causing the impeller to not come off. There is not much room for the Dremel so be careful not to nick the pump housing or cut into the motor shaft. Keep the vacuum close by to clean out the plastic impeller shavings. Clean the rust off the shaft with steel wool, fine sandpaper etc. Assembly was easy once everything was cleaned up.
Read less
Other Parts Used:
IMPELLER Disk & Mount Assembly
  • Craig from Southern Pines, NC
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    More than 2 hours
  • Tools:
    Nutdriver, Screw drivers
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • 1
Back to Top
Questions and Answers

Be the first to ask our experts a question about this part!

Back to Top
You May Also Need ?
Pump Housing Kit
$55.25
$55.25
  In Stock
Seal, Drain Cover
$6.84
$6.84
  In Stock
Motor Shaft Seal Head
$65.01
$65.01
  In Stock
IMPELLER
$71.82
$71.82
  In Stock
Back to Top
Model Cross Reference
This part works with the following models:
PartSelect Number: PS11741267
Manufacturer Part Number: WP3369012
Brand
Model Number
Description
Kenmore
110723120
Dishwasher
Kenmore
66514212K900
Dishwasher
Kenmore
66514212K901
Dishwasher
Kenmore
66514213K900
Dishwasher
Kenmore
66514213K901
Dishwasher
Kenmore
66514214K900
Dishwasher
Kenmore
66514214K901
Dishwasher
Kenmore
66514219K900
Dishwasher
Kenmore
66514219K901
Dishwasher
Kenmore
6651514590
Dishwasher
Kenmore
6651514591
Dishwasher
Kenmore
6651514593
Dishwasher
Kenmore
6651514594
Dishwasher
Kenmore
6651544590
Dishwasher
Kenmore
6651544591
Dishwasher
Kenmore
6651544593
Dishwasher
Kenmore
6651544594
Dishwasher
Kenmore
6651644590
Dishwasher
Kenmore
6651644591
Dishwasher
Kenmore
6651644593
Dishwasher
Kenmore
6651644594
Dishwasher
Kenmore
6651711590
Dishwasher
Kenmore
6651711591
Dishwasher
Kenmore
6651711592
Dishwasher
Kenmore
6651741590
Dishwasher
Kenmore
6651741591
Dishwasher
Kenmore
6651741592
Dishwasher
Kenmore
66517422990
Dishwasher
Kenmore
66517422991
Dishwasher
Kenmore
66517422992
Dishwasher
Back to Top
Customer Service Representative

Get in touch, we're here to help!

Daily 8am - 9pm EST

Contact Customer Service
Disk & Mount Assembly
$ 36.46
  In Stock
✖
Stock Status
 In Stock

Item is in stock and will ship today if your order is placed before 4:00 PM Eastern Standard Time.

If your order is placed after 4:00 PM EST, the in stock items will ship on the next business day.

 On Order

Item is not in stock and usually ships 3-5 business days from the time you place your order.

 Special Order

Item is not in stock and usually ships 10-15 business days from the time you place your order.

 NLA - No Longer Available

This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.