Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Carlos J - June 10, 2023
Verified Purchase
Easy repair
It was the correct part. Just plug in new one.
★★★★★
★★★★★
Khalid Q - November 5, 2021
Verified Purchase
Worked as advertised for 17yo whirlpool
This was an easy 'plug and play' repair for a nonfunctional surface heating element. Only tricky thing was matching the amperage range with element power. Both the 1200w and 1800w switches are listed for 6" elements. On the whirlpool gr445lxms, this is the correct switch for the front right 8'" /1800w element.
★★★★★
★★★★★
Jon G - November 18, 2020
Verified Purchase
Infinite switch
Received the right part, in great shape. Fit perfectly and works great
★★★★★
★★★★★
Jack W - March 6, 2019
Verified Purchase
Replacement control and knob
The parts I received were an exact match and are in good working order. Thank you.
< Prev
1
Next >
Customer Repair Stories
Average Repair Rating: 4.4 / 5.0, 7 reviews.
What's this?
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Element temperature inconsistent
Turn off power to the stove (unplug or turn off breaker) Remove back panel screws (Phillips) and back panel Unplug switch Remove knob and attaching screws (Phillips) Remove and replace switch Reinstall screws for switch and plugs in the back Snap off the end of the stem if it's too long and reinstall knob
... Read more />Reinstall back panel and turn power back on
*important: the large element has an updated switch and you may need to snap off the end of the stem with pliers! It's too long and there are no instructions for this included!*
Read less
Nathan from WHITE RIV JCT, VT
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
1 personfound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Over heating element.
Just turn off power , remover screws. Remove and plug in new part.
carlos from TRACY, CA
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
1 personfound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Cooktop on and cooktop hot indicator lights stayed on.
Range surface element control switch was bad. Replaced the switch and every thing works fine. Removed two Philips head screws in front and two Philips head screws in back of the range. Pulled the front panel away from the back of the range with the power off of course. Unplugged the wires and removed the two screws that held the switch in
... Read more. Replaced the switch and refastened the control panel. Tested the switch and every thing worked fine.
Read less
MICHAEL from FOUNTAIN INN, SC
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
1 personfound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
could not control the temp of the element
take off back panel, simply unplug the old switch and plug in the new one. Simple
Steve from GREENBRIER, TN
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Screw drivers
2 of 2 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The burner would not shut off.
Pulled the dial off, unscrew two screws. Pull the switch out from the back. Disconnect the wires from the old switch and connect to the new switch one by one. Set the new switch in place. Sctew the two screws in to hold the switch in place. Push on the dial.
Richard from CONCORD, NH
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
6 of 8 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
One of the heat elements in my oven would not heat
1. Disconnected power from my oven. 2. Removed several screws that held the control block 3. Removed two screws that held the switch itself disconnected wires and removed switch 4. Reconnected all wires to new switch (no soldiering gun required) 5. Put control block back
Overall - very easy
Mikhail from Iowa City, IA
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Screw drivers
21 of 28 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
water pump went out
it was very easy i took the pump off only two clips and two hoses holding it type in the model number at parts select it came right up soi new it right one from the picture got with in 3 days put it back on less then 10 mins
paul from windsor, VA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers
2 of 12 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
Next >
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
27 questions answered by our experts.
Sort by:
< Prev
1
2
3
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Tina
September 22, 2017
The front burner on the left side is always red hot even when it's on 3. Not sure which part i need. Googled it and was told it's the infinite switch? Would that be the correct part to fix the issue?
For model number Aer5830vaw
Hi Tina, Thank you for the question. I suggest replacing the switch that controls the burner.Surface Burner Element Switch - 8",PartSelect Number PS11740783.The element switch controls the heat of the surface burner. Disconnect power to your range before completing this repair because you will be working closely with electrical circuits. Remove the screws from back panel and the console, and remove the console to expose the switch. It is recommended to check for overheating or arcing on the wiring harness in case they need to be replaced as well. The harness that connects to the switch features a slip-on terminal for easy installation. Good luck with the repair !
13 people found this helpful.
Was this helpful?
Thank you for voting!
Sergio
September 30, 2019
The front burner on the left side and the back burner on the right side are turning to high even when they are on the low setting. According to your site it would be an infinite switch for each, but i am not sure which burner switches i need as both burners seem to be 8''. The part number that shows up on your site is for a 6'' burner ps11740774. Please advise. Thank you
For model number Amana model AER5522VCS
Hello Sergio, thank you for inquiring. You will need two of the 8" Surface Burner Element Switches, part number PS11740783 for your model. Good luck with your repair!
7 people found this helpful.
Was this helpful?
Thank you for voting!
Charles
August 16, 2017
8" burner heats to maximum (redhot) even when the selector is placed to the "5" number position which is medium heat. Is this a problem in the burner or the selector switch?
For model number RF367LXKQ
Hi Charles,
That is a good question. I believe that it would be a problem with the element, however I would suggest testing both the element and the switch with a multi-meter to see which one is malfunctioning. Both the switch and the element could cause an issue like that so it is best to test both. Good luck with your repair!
2 people found this helpful.
Was this helpful?
Thank you for voting!
Robert
February 18, 2020
Westinghouse stove 2 burners when turned on to low, go up to hot by themselves?
For model number WFC310S0EB0
Hello Robert, Thank you for the question. This normally indicates the switch that controls the element is defective and will need to be replaced. We hope this helps.
2 people found this helpful.
Was this helpful?
Thank you for voting!
Karen
July 25, 2021
The left front burner occasionally turns red-hot on a 2-3 setting. What is the part number I need to order?
For model number RF386PXEQ0
Hello Karen, Thank you for the question. This would be an indication the switch that controls the element, PartSelect Number PS11740776 is defective and will need to be replaced. We hope this helps!
Right front range burner only gets slightly warm. Is this a problem with the switch or with the element? Will you please advise your part number for the suspect part. Thanks.
For model number KERA205PSS2
Hello Charles, thank you for writing. You will want to replace the Surface Element part PS11746044 for your model.
1 person found this helpful.
Was this helpful?
Thank you for voting!
JS
August 26, 2019
I tried to open the front left burner and a spark came out of the switch, immediately after I was not able to open it anymore. Even the red light doesn’t work with this burner. All the other burners work fine. What do you think is my problem? Thank you.
For model number YWFC310S0EW1
Hello,
Thank you for your question. If the indicator light for the burner is not coming on when you turn the burner on and a spark came out of the switch that controls the left front burner, then that switch will need to be replaced. The part number listed under your model number for the left front burner switch is PS11740783. I hope this helps. Thank you and have a great day!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Bill
November 18, 2017
Left front 8" burner cannot be turned on and off because the manual control switch on the top left console cannot be turned. I believe these are called infinite switches but am not certain. Can you help?
For model number RF361PXKQ
Hello Bill,
Thanks for your question. The 8-inch surface burner infinite switch is part number PS11740775, and controls the functions of the surface element.
I hope this helps.
Surface indicator light stay on when all the switches are off. How can i fix this?
For model number RF263LXTQ3
Hi Ray,
Thank you for your question. You would likely have to replace your indicator light to fix that issue. I hope this helps. Good luck with your repair.
Part number for an 8 inch infinite switch burner. Thanks
For model number RF263LXTS3
Hi Billy,
Thank you for your question. The part number listed under your model number for the 8 inch infinite switch is PS11740783. I hope this helps. Thank you and have a great day!
1 person found this helpful.
Was this helpful?
Thank you for voting!
< Prev
1
2
3
Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
