This ice level arm, also known as an ice shutoff arm, is designed to detect the level of ice within the ice bin of your ice maker or refrigerator and turn it off when enough ice has been made. When the ice maker is empty, the arm will be down. When the ice maker is full, the arm will be raised, and over time, wear and tear to the level arm can cause the ice maker to stop making ice completely. To replace this arm, unplug your appliance and remove the ice making assembly, then pull the levelling arm out of the assembly and place the new one. Consisting of a long, angled metal arm and a plastic flap, this level arm is a genuine OEM part that is compatible with a wide-range of refrigerators and icemakers and measures at approximately 9-inches by 4.5-inches.
How Buying OEM Parts Can Save You Time and Money
Part Videos
Replacing your Whirlpool Refrigerator ARM-SHUT
Troubleshooting
This part fixes the following symptoms:
Ice maker not making ice | Ice maker dispenses too much ice
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Jeffrey S - April 28, 2023
Verified Purchase
Worked well, but very expensive
The part installed as advertised and is working properly. I am not happy with the high price, but I'm hoping the part will last
★★★★★
★★★★★
Dianne D - March 20, 2019
Verified Purchase
Simple fix
It was easy to identify and order the correct part. The package arrived quickly and installation was simple. While the video showed a more complex installation process, I simply used a cosmetics mirror to see the area the arm needed to be inserted into. All is working well.
★★★★★
★★★★★
Mary F - February 19, 2019
Verified Purchase
Easy repair
Repair was easy, but they should make it clear that the replacement Whirlpool ice maker no linger comes with this arm. Very annoying to get new ice maker installed and have to place another order fir this part.
★★★★★
★★★★★
Judy M - February 9, 2019
Verified Purchase
So far so good!
After watching the video on how to replace the arm-shut I realized I would have to make some adjustments to my replacement plan as my refrigerator is built-in and I can barely get to the ice maker in the freezer to fix it. But I managed to remove the plastic piece from the metal arm (which is the same peice that kept coming off my Kitchenaid) and reattach it to the wire in the ice maker which I could not really see. It seems to be working fine. The Kitchenaid part is very poorly designed, kept coming off just about every time you closed the ice drawer. I think this will work fine.
★★★★★
★★★★★
Gene G - March 5, 2018
Verified Purchase
Replacement ice maker
I earlier purchased a replacement ice maker for my Kitchen Aid refrigerator. Like so many do it yourself people I took the old unit out and threw it away. When you supplied me with the replacement a few days later, I found out that ishould have kept the shut off arm. So I then had to purchase it separately. That was very inconvenient.
★★★★★
★★★★★
John U - January 30, 2018
Verified Purchase
Works perfectly so far
The ice maker cut off arm that originally came my Whirlpool Refrigerator, got bent and could not straighten it out. The replacement either the”White flag” is working.
< Prev
1
Next >
Customer Repair Stories
Average Repair Rating: 4.4 / 5.0, 10 reviews.
What's this?
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
After installation, ice maker wouldn't function at all
I took the ice maker out to check things when it wasn't working and I noticed what wasn't visible with the maker installed. The input hose was filled with ice. An ice pick didn't really work so I filled an empty Windex bottle with hot water and sprayed the ice until it was gone. I installed the ice maker again and it's working well.
no shut-off for ice production; shut-off arm broken/missing
Inserted the prongs of the replacement shut-off arm in the holes provided in the bracket.
Victoria from MELBOURNE, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
1 of 2 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Ice maker was over producing
Technician at ASK suggested replacing ice maker. Ordered new ice maker(prompt delevery)then noticed it came without wire arm and white platic "flag". Ordered arm and "flag", replaced all old with new and seems to be doing well. Perhaps all I needed was the plastic "flag" on the limit arm wire. Will never know. The new icemaker wiring had
... Read moreshort wires and a connector. Old ice maker had no connector so the short wires were removed and the old wires plugged into the ice maker. Mirror was required in order to see the side wall mounting screws. Very narrow work area, tiny freezer side.
Read less
Gregory from Milford, OH
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
6 of 8 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Ice marker would not stop going though its cycle and fill with water
Got on line with Partselect and follow their directions. It was very easy.
Replacing the parts was easy. I am 62 years old and have been repairing all my own appliances for yerars. I have found more problems in recieving the corect parts in a timley mater more difficult than fixing the problem. I am impressed with the promedness of your delivery, and in rtecieving the corect parts. Thank you much!!!!!!!!!!
... Read more! Bill
took out old ice maker (3) screws unpluged power plugged new one in replaced screws , installed new icemaker shut off arm and done Ice bin auger disassembled bin to get at auger drum replaced broken auger reassembled bin and done 30 min tops hardest part was figuring out how to get bin apart
I just followed the instructions that came with the unit, it was very easy. The old ice maker was taken out some time ago, so all I had to do was install the new one. It was three screws and one electrical plug. I removed the ice maker over a year ago and did not replace it at the time. I purchaced new handles also and they were easy to r
... Read moreeplace. I then decided to try the ice maker, I got tired of buying ice at the store. The order came in just two days right to my front door. It was a very easy fix and now I have a refrigerator full of ice. Thanks for the great service.
open ice maker door, use mirror to view slot in front of ice maker, slip piece in place and done
Thomas from Va. Beach, VA
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
52 of 76 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
Next >
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
4 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Joan
June 13, 2019
Re part #31 (ice shut off arm). The original part, which I have, has popped out of place. When I try to place it back, it continues to pop out, even though both ends are being inserted into the correct openings. I'm wondering if there is another part needed, like a that holds it in place? Thank you.
For model number KSCS25FKSS
Hello Joan, Thank you for the question. The arm should just fit in place with no other parts required. The arm may have become bent or warped not allowing it to stay in place. Hope this helps!
3 people found this helpful.
Was this helpful?
Thank you for voting!
Sarah
September 3, 2019
Can’t find the part number for the plastic piece that goes on the metal arm shut off. Can you help me out? Thanks much
For model number WRS322FDAM04
Hello Sarah, Thank you for the question. The plastic part on the Arm is only sold as part of the Shut Off Arm, PartSelect Number PS12712096. Hope this helps!
3 people found this helpful.
Was this helpful?
Thank you for voting!
Bruce
January 22, 2023
Ice maker continues to make ice after the arm shut is in the (UP) off position. Also continues to make ice after bin is full and overflowing with ice.
For model number ED5VHGXM011
Hello Bruce, thank you for your question. This sounds very much like an issue with the Shut Off Arm PS12712096. This gives the icemaker a signal to stop making ice once the bin has a reached a certain limit. We are pleased to have been able to help.
1 person found this helpful.
Was this helpful?
Thank you for voting!
Ed
July 11, 2019
I bought and installed this part and the ice maker arm stays up after the cycle so will not go down to make ice again.. any idea?
Hello Ed, thank you for contacting us,This is more then likely an issue with the ice maker if the new arm did not fix the issue. In order for us to locate the correct parts and repair information we will require the model number of the unit. Once you have located the model number please feel free to resubmit the question and we will be happy to help you. Look forward to hearing from you!
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
