Maytag/Maytag_Thumb/37271.gif
See part 27 in the diagram
( Grid squares measure 1x1 inch )

Get in touch, we're here to help!

Open until 10PM EST

customerservice@partselect.com

Spring Retaining Clip

★★★★★
★★★★★
2 Reviews
$ 6.99   In Stock

Get this part fast. Average delivery time via standard shipping: 1.8 days.

PartSelect Number PS11739294
Manufacturer Part Number WP22001650
Manufactured by Whirlpool
Product Description

Spring Retaining Clip Specifications

This spring retaining clip is just under 1 inch long. The clip is made entirely of metal and is attached to the back wall of the washer, under the console. If your washer is vibrating and louder than usual during the wash cycle, your spring retaining clip could be faulty or damaged. Check the clip for visible damage, wear, and rust. If you notice any signs of damage, the part should be replaced. Remember to disconnect the power from your washing machine before starting this repair.

How Buying OEM Parts Can Save You Time and Money

Troubleshooting
This part fixes the following symptoms:
Noisy
This part works with the following products:
Dryer, Washer, Washer Dryer Combo.
This part works with the following products:
Maytag, Amana, Speed Queen, International.
Part# WP22001650 replaces these:
AP6006227, 212982, 22001650, 28835, 56080, R0601520
Questions and Answers

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

3 questions answered by our experts.
    Sort by:
    Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
    Charles
    November 30, 2017
    How do you install a metal clip that holds the front to the top of this Maytag dryer?
    For model number LDE9304ACE
    Hi Charles,Thank you for the question. To install the new clips you will need to remove the front panel. At the bottom of the panel there are 2 Philips head screws that will need to be removed.Once the panel is removed you will be able to see the Spring Retainers. With a large pair of pliers and compress the retainer and release it from the panel. Next you will need to compress the new retainer with the pliers and slip the long tab in the hole pointing towards the front of the panel and then the smaller towards the back. Next reinstall the panel and screws. Hope this helps!

    6 people found this helpful.

    Was this helpful?
    Thank you for voting!
    Lisamae
    July 15, 2019
    Dear Sir, Do you have the following parts for the Whirlpool Maytag washer? 22001441, pulley, and WP22001650, fastener.
    For model number 22001441 PULLEY WP22001650 FASTENER
    Hi Lisamae, Thank you for your question. We do have the spring retaining clip or fastener available for you, but the pulley has been discontinued by Whirlpool and you will need to contact them for information on a replacement part. Their telephone number is 1-866-698-2538. If they provide you with a part number for the replacement part, you may call us back with it and we can verify if we have it available for you. You may also be able to locate the part you need by trying the following: Using a search engine to type your part number and see if other retailers still have this part in stock. Visiting online stores such as eBay and finding sellers that have this part. Trying retailers and repair stores in your local area to see if they have the part in their inventory. Talking to a local repair technician, who may have the part you need, or may be able to repair your existing part. I hope this helps. Thank you and have a great day!

    2 people found this helpful.

    Was this helpful?
    Thank you for voting!
    Joseph
    July 12, 2019
    Trying to take off the bottom that has clip to clean it out from lint
    For model number MEDX700XW0
    Hello Joseph, Thank you for the question. Once the top clips are depressed it should release the top and you can tilt it out then lift it off the bottom clips. Hope this helps!

    1 person found this helpful.

    Was this helpful?
    Thank you for voting!
      Customer Repair Stories
       Average Repair Rating: 2.8 / 5.0, 8 reviews. What's this?
        Sort by:
        Sorry, we couldn't find any existing installation instruction that matched.
        unusually loud rumbling in spin mode, no spin out
        removed outer enclosure to expose inside workings. removed all retaining springs to tub and transmission housing. Inverted tub to access agitator pulley and belt. Removed pulley and cut belt off.(I knew I was replacing it, anyway.)Had to remove large tub bracket to exchange new pulley for old. Disconnect bleach reservoir filler tubing on tub assembly. Disconnect power connector to drive motor. Removed water pump to access drive pulley where new belt belongs. Aligned belt to pulleys and checked idler pulley tension which was acceptable. Replace helix drive lug against spin/agitator and tightened retaining bolt. Assembled components in reverse order and conducted test run. Success. Smooth running machine and saved about $200 on professional labor costs. I had no repair manual but you should have a personal confidence in general repair work. Something like a history of taking things apart and putting them back together successfully. I had an independent appliance repair guy examine the washer and he said it was too complicated for him. Once I had it apart, it seemed fairly basic. Good luck!
        • Ralph from Moreno Valley, CA
        • Difficulty Level:
          Easy
        • Total Repair Time:
          1- 2 hours
        • Tools:
          Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
        34 of 42 people found this instruction helpful.
        Was this instruction helpful to you?
        Thank you for voting!
        Agitator action was slow/weak; Bleach tube kinked
        UNPLUG THE MACHINE FIRST!
        a) Remove the front panel (use a putty knife to release clips)
        b) Fashion a small hook-end out of a coat hanger
        c) Install an additional glide spring (2 + 1 = 3) to get extra retraction of vee-belt around drive pulley as follows.
        d) Hook end of of the new spring onto rear (back) hole of moving motor mount (observe orientation of existing springs to be sure that you're hooking up spring into hole correctly).
        e) Lie on your right side, hold the spring in place with your left hand (go around back of the motor with your left hand).
        f) Have someone hold the flashlight as you take a coat hanger and fish for the front end of the spring under the motor glide.
        g) With front - end of spring held by coat hanger hook, pull spring towards you and slip spring into front hole of stationary motor mount.
        h) Lightly spray in and around glide area with Teflon non-stick dry lube (DuPont or Liquid Wrench dri-lube product line).
        Machine agitates like-new now.
        Bleach Tube:
        a) Remove hose clamps at both ends using a screwdriver.
        b) Remove and discard old tube.
        c) Slip on the hose clamps and slicker-up the ends of new tube with palmolive liquid detergent and slip onto tub and bleach dispenser.
        d)Tighten clamps.
        • Robert from Marlboro, NJ
        • Difficulty Level:
          Easy
        • Total Repair Time:
          15 - 30 mins
        • Tools:
          Screw drivers
        • Parts Used:
          WP22001650, WP22001320, 205000
        25 of 35 people found this instruction helpful.
        Was this instruction helpful to you?
        Thank you for voting!
        Many problems
        It would seem that my unhappy washer decided to
        have a multiple component breakdown. after replacing one part after another, my baby runs like new. parts arrived quickly and installed easily, it was all the diagnostic that took the most time. the forums were quite helpful.
        • Deanna from Fort Lauderdale, FL
        • Difficulty Level:
          Difficult
        • Total Repair Time:
          More than 2 hours
        • Tools:
          Screw drivers, Wrench set
        • Parts Used:
          WP22001650, WP207166
        8 of 19 people found this instruction helpful.
        Was this instruction helpful to you?
        Thank you for voting!
        Tub gasket leaking because of age.
        Top came off quickly with socket wrench. Removed gasket in about a minute. Spent 45 minutes getting grime ( soap and lime) off of top. Took five minutes to replace gasket.

        Haven't been able to get front back on. Clips go on side rather than top. Found missing clip for which new one was purchased in transmission. Still haven't gotten front to stay on. Clips keep springing out.
        • Donald from GROSSE PT PK, MI
        • Difficulty Level:
          Really Easy
        • Total Repair Time:
          1- 2 hours
        • Tools:
          Screw drivers, Wrench set
        • Parts Used:
          WP22001650, WP22001007
        2 of 2 people found this instruction helpful.
        Was this instruction helpful to you?
        Thank you for voting!
        Water leak at bottom of tub, leaking onto floor.
        Repair not that complicated. Remove front, lean top back, remove agitator, remove special nut, remove inner tub, remove seal. Clean shaft and seal surfaces. It is highly recommended to the spanner wrench to remove the special nut. It appears one can do it with a punch and hammer, but the nut is too tight, and corroded from years of water exposure. I believe part number is TJ90TB123A, about $15. Watch the video on this web site, very good.
        • Brian from Allentown, PA
        • Difficulty Level:
          A Bit Difficult
        • Total Repair Time:
          1- 2 hours
        • Tools:
          Nutdriver, Screw drivers
        • Parts Used:
          6-2095720, WP22001650
        2 of 3 people found this instruction helpful.
        Was this instruction helpful to you?
        Thank you for voting!
        30 year old washer started to leak on left side
        Noticed small pool of water on left side. Diagnosed it was injector tube. Ordered parts.

        Removed front panel by removing two phillips screws and then pushed down to disengage spring clips.

        Used nutdriver to remover two bolts holding top cover and then undid bleach dispenser hose.

        Lifted top cover and removed clamps holding injector and fill. Replaced using 1 1/16" Stainless steel screw clamps.

        THIS WAS THE FIRST REPAIR EVER ON THIS WASHER!! SIMPLY AMAZING PERFORMANCE. STILL SPINS AT HIGH RPM AND IS QUIET. Bought for my folks as a gift in 1979.

        This is the reason I bought the last Maytag top loaders made in '05. Also had another one 24 years with only one repair.

        Parts Select, thank you! Parts arrived in three days.
        • Richard from Ridgefield, CT
        • Difficulty Level:
          Easy
        • Total Repair Time:
          30 - 60 mins
        • Tools:
          Nutdriver, Screw drivers, Wrench set
        1 of 2 people found this instruction helpful.
        Was this instruction helpful to you?
        Thank you for voting!
        Dryer was making a loud screeching noise
        Once I determined where the noise was coming from I took the front cover off, two screws at the bottom and clipped at the top. Then I removed the lint screen shroud . Instructions said to remove belt and drum, but I was able to pull the drum forward enough to get to the roller without removing the belt. I removed the snap ring from the shaft holding the roller...cleaned up the shaft and installed new roller with fiber washers. Slid the drum back in place and put shroud and front cover back on. I also replaced a front panel clip that I had broken on a previous repair. It just snapped into place.
        • Andy from York, PA
        • Difficulty Level:
          Easy
        • Total Repair Time:
          30 - 60 mins
        • Tools:
          Screw drivers
        • Parts Used:
          WP22001650, 12001541
        1 of 3 people found this instruction helpful.
        Was this instruction helpful to you?
        Thank you for voting!
        noise coming from dryer and low air flow
        Remove front panel, front drum support, remove belt, drum, blower cover, spring clip, blower cover, blower wheel assy.
        Ordered new parts on line, came in two days, good service. Cleaned out all lint and installed new parts in reverse order.
        • Ronald from Aliquippa, PA
        • Difficulty Level:
          Easy
        • Total Repair Time:
          15 - 30 mins
        • Tools:
          Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)
        • Parts Used:
          WPY312959, Y303836, WP22001650
        1 of 4 people found this instruction helpful.
        Was this instruction helpful to you?
        Thank you for voting!
          Customer Reviews
          Average Rating:
          ★★★★★
          ★★★★★
          2 Reviews
          5.0
          Filter By Rating:
          • 5 Stars
            2
          • 4 Stars
            0
          • 3 Stars
            0
          • 2 Stars
            0
          • 1 Star
            0
            Sort by:
            Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
              Model Cross Reference
              This part works with the following models:
              PartSelect Number: PS11739294
              Manufacturer Part Number: WP22001650
              Brand
              Model Number
              Description
              Maytag
              6329
              Washer - MAYTAG AUTOMATIC WASHER
              Maytag
              6349
              Washer - MAYTAG AUTOMATIC WASHER
              Maytag
              6359
              Washer - MAYTAG AUTOMATIC WASHER
              Amana
              7493-LEM437
              Dryer - DRYER
              Maytag
              A104
              Washer - Top Loading
              Maytag
              A105
              Washer - Top Loading
              Maytag
              A106
              Washer - Top Loading
              Maytag
              A106S
              Washer - Residential
              Maytag
              A107
              Washer - Top Loading
              Maytag
              A107S
              Washer - Residential
              Maytag
              A108
              Washer - Top Loading
              Maytag
              A108S
              Washer - Residential
              Maytag
              A110
              Washer - Top Loading
              Maytag
              A112
              Washer - Top Loading
              Maytag
              A15CA
              Washer
              Maytag
              A15CM
              Washer
              Maytag
              A15CT
              Washer
              Maytag
              A16CA
              Washer
              Maytag
              A16CM
              Washer
              Maytag
              A16CT
              Washer
              Maytag
              A17CA
              Washer
              Maytag
              A17CM
              Washer
              Maytag
              A17CT
              Washer
              Maytag
              A180
              Washer - Top Loading
              Maytag
              A181
              Washer - Top Loading
              Maytag
              A182
              Washer - Top Loading
              Maytag
              A183
              Washer - Top Loading
              Maytag
              A18CA
              Washer
              Maytag
              A18CM
              Washer
              Maytag
              A18CT
              Washer

              Get in touch, we're here to help!

              Open until 10PM EST

              Contact Customer Service