This washing machine water inlet valve has two ports for water to enter. This water inlet valve attaches the water lines to the back of your appliance. The attaching solenoids on the valve open and close according to the desired temperature, or amount of water needed.
How Buying OEM Parts Can Save You Time and Money
Part Videos
Replacing your Maytag Washer Water Inlet Valve
Troubleshooting
This part fixes the following symptoms:
Leaking | No hot or cold water
This part works with the following products:
Washer, Washer Dryer Combo.
Part# WP22001274 replaces these:
AP6006209, 22001273, 22001274
Customer Reviews
Average Rating:
★★★★★
★★★★★
17 Reviews
4.2
Filter By Rating:
5 Stars
12
4 Stars
2
3 Stars
0
2 Stars
0
1 Star
3
Sort by:
< Prev
1
2
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Gregory R - August 19, 2022
Verified Purchase
Works great
Fits, looks and works just like the original. I've had the same experience with all of the parts that I've received from the Parts Select gang.
★★★★★
★★★★★
Murray M - July 28, 2022
Verified Purchase
Over priced
Over priced - After making the purchase, I found the same part price much cheaper on other websites.
★★★★★
★★★★★
Alden M - August 13, 2021
Verified Purchase
Is easy repair
The part came relatively quickly was in good shape it was easy to change should it change that years ago.
★★★★★
★★★★★
David K - November 11, 2020
Verified Purchase
Onsite diagrams and info are the BEST!
A bit pricey, but I shopped around, and it was the best deal I could find. My old valve was letting a little water drip into the tub. Not good after you spin the clothes to get the water out! But this fixed it, and it was simple to do. Thanks!
★★★★★
★★★★★
Mary Ellen B - July 3, 2020
Verified Purchase
Easy repair
The part looked exactly like the 30+year old part it replaced. Easy replacement.
★★★★★
★★★★★
ROBERT T - April 30, 2020
Verified Purchase
Easy repair
Take old one out put new one in very simple and easy
★★★★★
★★★★★
David C - January 19, 2020
Verified Purchase
Great part
Fixed my problem
★★★★★
★★★★★
Roger T - November 23, 2019
Verified Purchase
Part had been updated with one less connection
Was unable to get any info if the part was ok to install with one less electrical connection then old part.. Your reference material didn't go far enough back. I finally called an appliance repairman from my area and he told me to use tape on the extra wire. A long time to find out info with a 15 minute repair..
★★★★★
★★★★★
Richard B - May 5, 2019
Verified Purchase
Was Not The Solution
My twenty-three and one half year old Maytag washer would only work on the cold/cold cycle. This was the first problem I ever had with the unit. After reading all of the website commentary, I thought this part would correct the problem. The part was in good condition and was easy to install; however, it did not correct the problem. Because of its old age, I have since replaced the washer. I am neutral on the part and cannot give it a rating. Also, since it had been installed, I am ineligible to return it for credit.
★★★★★
★★★★★
Alaine B - April 22, 2019
Verified Purchase
Easy repair - great part - worked as expected!
The part was in great condition and worked as expected.
< Prev
1
2
Next >
Customer Repair Stories
Average Repair Rating: 3.8 / 5.0, 20 reviews.
What's this?
Sort by:
< Prev
1
2
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Washer would only work on cold/cold cycle.
The replacement instructions are clearly shown on YOUTUBE. I followed these instructions precisely. After reading PartSelect website commentaries, this part appeared to be what I needed. However, after installation the problem continued. The washer is twenty-four and one half years old and this was my first problem. Since it was function
... Read moreing on borrowed time, I gave up on further repairs and ordered a new clothes washer.
Read less
Richard from WESTLAKE, OH
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers, Socket set
2 of 2 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Water level Uncontrolled, Belts squeeking
Removed face of control panel, removed cover on back of machine that allows access to water level hose. Disconnected hot and cold water supply. Pulled old water level hose off tub. Had to use screw type hose clamps to install as diameter of hose different from original. Removed hoses from water inlet valve. Easily installed new valve. Til
... Read moreted machine on it's face to access belts. Took five minutes to replace.
After first unplugging the washer and shutting off the water to the washer I slid the washer away from the wall. It was a tight cramped space and difficult to get behind it. Most of the time replacing the water inlet valve was spent getting into and out of the work area to get tools and cleaning up a few years of dirt under the washer and
... Read more water leaking from the hoses after they were removed. The valve removal and re-installation of the new one was pretty straightforward.Just a 3 screws 2 electrical connectors and three hoses. The water inlet hoses were frozen on the old valve and required a wrench to free. I also needed to replace the hose washers which fortunately I had as spares for my garden hoses. I replaced the solenoid leads directly from the old to new valve so as not to get that wrong. Removing the outlet hose clamp was tricky- I needed a fat wrench to depress all the tines and slip it off. Fortunately I was able to reuse it. After securing the mounting screws and tightening the inlet hoses with a wrench just until I met some resistance, I turned the power and water back on and prayed there were no leaks. None- back in business.
Read less
Robert from Saratoga, CA
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers, Socket set
23 of 26 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The water to the washing machine continued to run into the unit when it was supposed cut off. It continue to fill overflowing the tub of the washing machine and onto the floor. The water had to be cut off at the wall in order to stop the inflow of water.
I disconnected both water hoses from the back of the machine. I then unscrewed the panel that holds the water inlet valve. After disconnecting the two electrical connections from the valve and replacing it with the new unit, the job was done.
Donnie from Spring, TX
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Pliers
8 of 13 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Inlet Valve
The valve was leaking. I shut off the water to the machine and unplugged the power supply. I removed the defective valve. I then installed the new replacement valve reconnecting the 3 hoses and the 4 wires to the selenoid. I plugged it in and tried it before I pushed the machine back in place. I had to retighten one of the hose connection
... Read mores due to leaking. The leak stopped and I then pushed the machine back in place.
It saved me some $500.00, the cost of a new machine.
Read less
roy from collierville, TN
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers
5 of 7 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Water would not stop running
Right part sent very quickly.
Cathy from Newnan, GA
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers, Socket set
2 of 3 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Cold water inlet was limiting flow, resulting in slow tank fill time.
When selecting a cold cycle, the inlet valve would allow for slow water flow resulting in 15+ minute tank fill times.
I unplugged the washer, disconnected all water sources.
I removed the 3 screws holding the water inlet value and cover. Disconnected all cabling and water tubing. Replaced valve, reconnected all c
... Read moreabling and reinstalled.
While I was doing the repair on the inlet value. I replaced the hose washer and also installed a screen kit at the home water valve. The home is supported by a well and at times sees sedimentation in the water which could have sparked the initial issue to begin with.
I did clean the old water inlet valve once before which fixed the problem temporarily. It was time to replace the entire part.
Water leaking into basin when washing machine not in use
Turn off water. Disconnect hoses from washer. Remove drain hose from plumbing drain in wall. Catch water from all three hoses in plastic tub. Remove two 5/15 machinve screws holding inlet valve cover/mount plate. Remove fill hose by compressing hose clamp ends with pliers. Remove electrical connections. Reverse to install. Easy as p
... Read moreie!
Read less
Tate from Carrollton, TX
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers, Wrench (Adjustable)
9 of 12 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
washer would not fill with water
The trouble-shooting section on this website described the above problem and suggested that the proper course of action was to replace the water inlet valve, which I ordered and replaced. Replacement of this part was quick and easy.
Fredrick from Clinton Corners, NY
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
20 of 26 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Blown Fuse
We were having some very cold weather and some element of the washing machine was making the fuse blow; probably, I realized, because something had frozen. I thawed it out, replaced the fuse, and all good. But, it started to blow fuses again. Their was no way to tell if it was the motor or some other device. I found the wiring diagram
... Read more taped to the inside of the cabinet. I noticed that the motor seemed to have thermal protection of its own, and that the only other device connected to the fuse was the water inlet valve. I ordered a new one, put that, and a new fuse, in, and did my laundry.
Read less
jim from palmer Lake, CO
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers
3 of 5 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
2
Next >
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
11 questions answered by our experts.
Sort by:
< Prev
1
2
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
BILL
August 28, 2017
Do I put the hot water hose on the top inlet or the bottom.
For model number LAT8004AAE
Hi Bill,
Thank you for the great question, The top is for the hot water and bottom is for the cold.
Thank you again for question and good luck with the repair!
2 people found this helpful.
Was this helpful?
Thank you for voting!
Roy
October 5, 2017
Water started to fill, when I closed the lid it stopped filling, both hot and cold water.
For model number LAT9304AAE
Hi Roy,
Thank you for your question. There are a couple of parts that you should check. I would suggest checking your lid switch and your lid check switch. It seems like this is the most likely problem. You may also want to check your water inlet valve as well. Good luck with your repair.
2 people found this helpful.
Was this helpful?
Thank you for voting!
Tonya
November 3, 2017
I took a load out of the washer and turned knob to start a new load, no water. The spin cycle works but it will not fill with water, no noise, no hum like it's trying, nothing, doesn't matter the temp selection either. Is it the inlet valve?
For model number LAT1916AAE
Hi Tonya,
Thank you for your question. That would be the first part to check, yes. Most times when you experience this problem, it has to do with the water inlet valve. I hope that helps. Good luck with your repair.
2 people found this helpful.
Was this helpful?
Thank you for voting!
John
April 28, 2018
Turn switch to hot cold, no water comes in the the tub in, & makes a humming sound. Other two settings is cold water only. Could this be the inlet valve? If so the serial # is 11078016sd to get the correct part # to place an order. Thank you
For model number LAT8226AAE
Hello John, thank you for your question. From your description the most likely issue is the water valve itself. I would suggest replacing the Water Inlet Valve WP22001274. Please enter the part number into the site for current price and availability. Good luck with your repair!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Amy
February 26, 2019
My washer will not fill with either hot or cold water. Nothing, no sounds or anything. The machine will spin but that's it. Does this sound like a faulty water fill valve? Can it be bench tested or does it need to be tested installed in the machine?
For model number Maytag LAT8705AAE
Hi Amy,
Thank you for your question. If the washer will not fill with water, it could be a faulty water inlet valve. The valve can be tested with a multimeter to verify if it is working correctly. If this is not the issue, there are some other parts that you will need to check to see which ones are causing the issue. You will need to check the lid switch assembly, the lid check switch, the hose washer and screen insert kit, the screens, the hose clamp and the inlet hose washer. I hope this helps. Thank you and have a great day!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Thomas
April 30, 2019
I am not sure if i need inlet valve or maybe lid switch? Washer will not fill but will spin on each selection
For model number LSE7804ACE
Hello Thomas, thank you for inquiring. For this symptom you will want to replace either the Water Inlet Valve part PS11739275, the Inlet Hose part PS11744637, or the Water Level Switch Kit part PS2003728. We hope this helps.
1 person found this helpful.
Was this helpful?
Thank you for voting!
Andy
June 20, 2019
The water (on hot or cold setting) trickles out while there's a jackhammering sound from the back of the cabinet. And then when the tub does finally fill up after about an hour, the wash cycle doesn't run. So i have a tub full of soaking laundry. Solenoid and possibly something else since it doesn't run even after filling up. Ideas?
For model number LSE7804ACE
Hi Andy, thank you for your question. Usually if your appliance is having trouble filling you should take a look at your water inlet valve for being the issue. The valve can be tested with a multi meter and should be reading between 500 - 1500 ohms of resistance. If that part is working then you might want to check your water level/pressure switch as well. I hope that helps. Good luck with your repair.
1 person found this helpful.
Was this helpful?
Thank you for voting!
Charlotte
December 14, 2019
I see part 7 valve; is that all one piece with the solenoid included?
For model number LAT9406AAE
Hello Charlotte,
Thank you for your question. The solenoid would come included with the water valve under part PS11739275. We hope this helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Bill
December 20, 2021
Granted it's 25 yrs old and never serviced yet but it's a gem of a Maytag. Washer started having difficulties/long delay in switching from wash to rinse for a couple of weeks now. Latest new thing is it also rinses hot though cold is selected and has always been cold rinse till now. Maybe timer unit?
For model number LAT9306AAE
Hello Bill, thank you for your question. We have researched the model you have provided, and we would suggest the Washer Timer, part number PS11739338. If you need help placing an order, our customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you!
After our electricity came on after 12 hours, we can only get hot water and no cold. Did the hot water solenoid fail in this 27 year old machine? Sounds like the water inlet valve needs to be replaced? Does that make sense to you? PS 11739275
Thank you for your help.
For model number LAT9304AAE
Hi Ned, thank you for reaching out. According to the symptom, it is most likely that the water inlet valve, part number PS11739275, is damaged and needs to be replaced. If you require assistance to place an order, please contact customer service. We hope that helps!
Was this helpful?
Thank you for voting!
< Prev
1
2
Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
