Quick Question!

Have you ever purchased from PartSelect.com before?

11738945-1-S-Whirlpool-WP216201-Rubber Injector Valve
11738945-1-S-Whirlpool-WP216201-Rubber Injector Valve 11738945-2-S-Whirlpool-WP216201-Rubber Injector Valve https://www.partselect.com/Schematics/Maytag/37308.gif

Rubber Injector Valve

Your Price

$10.33
Get this part fast. Average delivery time via standard shipping: 1.8 days.

PartSelect Number PS11738945
Manufacturer Part Number WP216201
Manufactured by Whirlpool

This part is commonly known to cause a leak at the top left corner of the outer tub. It fits over the injector nozzle. It is black in color and measures approximately 2 inches in length. To access this part, you will need to remove the front panel of your washer. There will be 2 screws holding it in place. Once these have been removed, the top will pivot to open, which will give you access to the injector assembly. This is an OEM part that comes right from the manufacturer and is sold individually.

This part works with the following brands: Maytag, Jenn-Air.

This part works with the following products: Washer, Washer Dryer Combo.

This part fixes the following symptoms:

  • Leaking.

Videos For installing this part.

Questions & Answers

Ask our experts a question on this part and we'll respond as soon as we can.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.6 / 5.0, 62 reviews What's this?
 

6 of 8 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver, Screw drivers, Socket set
Customer: EL from O'Fallon, IL

When filling tub to soak, water leaked from left rear corner

Removed front cover by removal of 2 phillips screws at bottom of front panel. Removed two cap screws from lf and rf corners attaching the top to the side panels. Raised and blocked up with piece of wood the hinged top of machine. Removed hose clamps with nut driver and cotter pin remover to expand the maytag clamps for reuse and to break the stick of the hoses to the old sleeve. Removed the clamp at the water fill valve on the water hose run up to the sleeve. Removed the water injector from the washer fill hose and removed the plastic injector for reuse in the injector hose. Inserted it into the fill hose as the old removed sample revealed. Installed the new improved plastic sleeve with one of two original screws, no longer using two but one screw for mounting. Installed original clamps on new hoses and reinstalled hoses on new sleeve. Pressed run dial center to start fill to ensure water leak was now cured. Reinstalled lf and rf cap screws to side panels. Reinstalled front panel 2 phillips retaining screws. Tested cycles and no leaks, on this 1966 machine bought new in may of 1966, along with its companion maytag dryer. Both remain in good use. A comparable maytag washer is 799. 00 At lowes. . . Thank you, fred maytag, for the best washer with the easiest design to repair, if it ever needs parts. . . And thanks, partselect. Com for having these 44 year old washing machine parts. Interesting to note that this sleeve not only had an added water fence around its open vent slots to prevent water overflow, but that it now tilted rearward on the oem mount to aid in that desire. It is always good to see american companies that are continually upgrading their parts to work better and to fit in older machines, like maytag has always done, in their search for excellence.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

6 of 8 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 1- 2 hours
Tools: Nutdriver, Screw drivers
Customer: Greg from Orem, UT

Water leak coming from rear, left side of washing machine.

Removed front access panel--very easy, two screws at bottom of panel, near the floor. Removed two more hex-headed screws that secure the top panel/lid to the top of the washing machine frame.
Most difficult problem was identifying the source of the leak. I saw water running out of a white, rectangular (about 1" x 3/4" x 3/4") box-like device that was installed in the water line that leads from the mixing valve (blue box, mounted at the back of washer) to the top of the tub. Discovered this device is called the injector assembly, have not yet been able to figure out what function it serves.
Disconnected one of the hose clamps that secure the injector assembly to the water hose. Removed the rubber injector valve and injector nozzle, the two parts that fit inside the above-described "box." Soaked the assembly "box" in vinegar to eliminate hard-water deposits. Replaced the two internal parts (injector nozzle & injector valve) with new (about $15, including shipping). This almost resolved the problem, still saw a small amount of water leaking from the whole assembly, but only about 5% of what was leaking. Haven't yet figured out why it's not completely dry, or what function that injector assembly serves.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

5 of 6 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers, Socket set
Customer: Rene from Yakima, WA

Water was going all over the floor

My washer is very old but in very good condition, it was my mothers when I was a teenager and now I am 50! This is the first repair ever done on it, my son was sure I should just buy a new one but my daughter and I had other ideas. We went on line and looked it up and followed easy directions and found the small part that was leaking right away.It had just worn out. we then ordered the parts for under $20.00 and within a few day's it was here and we were back in the laundry washing. Thank you soooo much, we are not going to let this one down with my son for some time =)

Help other customers find the most helpful instructions.

Were these instructions helpful?   

4 of 6 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers, Socket set
Customer: Forrest from San Diego, CA

Leaking water rear left side

This happened once before and had I remembered how to get the front door off and lift the top it would have taken me less time. I actually spent more time assessing prior to ordering parts than in repairing once the parts came.

One odd thing - it only leaked when the hot water was entering (if the settings were on cold only no leak - no idea why that should be).

Anyway, this injector and the rubber housing it slides into get old and clogged or deteriorate. I ordered all the parts and replace them - but probably only needed to replace the plastic injector nozzel and the rubber sleeve it fits into.

All good now - no more leaks (until the next time!)

Help other customers find the most helpful instructions.

Were these instructions helpful?   

3 of 3 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers, Socket set
Customer: Mark from Yorktown, VA

Washing machine leaked when filling

After removing the front cover and tilting up the top of the washer housing, the area of leakage was obvious. I unscrewed the clear plastic injector housing, loosened the clamp, slid the hose off of the clear plastic injector housing, and removed the plastic injector nozzle and the rubber injector valve.

I then order the plastic injector nozzle and the rubber injector valve. After the parts arrived, I simply put things back together, and no more leak!

Note: When putting the plastic injector nozzle into the rubber injector valve, I used a little liquid detergent as a lube.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

3 of 4 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: Lynn from Norwood, CO

The washer leaked on the lt side. The injector was wet.

Once the front and top of the machine were opened,
I loosened the clamps on each end of the injector. I removed the rubber injector valve and the plastic injector nozzle was inside. I placed the new nozzle inside the rubber valve making sure the lip of the nozzle was locked in the rubber valve as on the one I had removed. I used a little detergent to lubricate the wider end of the rubber valve(as suggested by someone else in their description). I placed the valve into the washer in the same way the old one came out. I tightened the clamps and started the machine. No leak. I put the top and front on and have been happily washing since. This machine was given to us used by my mother-in-law. It is at least 25 years old.
I assumed we would have to replace the machine, but we repaired it for less than $20., including shipping. Thanks.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

2 of 2 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver, Screw drivers
Customer: Arnoldo from AUSTIN, TX

Waher was leaking at the injecotr valve at the top left of the washer.

The three parts fit together to form one unit. As has been mentioned here already I'm not sure what purpose they serve. I'm also not sure how replacing them stopped the leak but it did. If it had not stopped I think I could have bypassed the valve entirely with a piece of hose or PVC and had it work just fine.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

2 of 2 people found this instruction helpful

Parts Used:
Level of Difficulty: A Bit Difficult
Time to do repair: More than 2 hours
Tools: Screw drivers, Socket set
Customer: Prosper J from Gretna, NE

Washer leaking water

After figuring out how to open the washer I could not find where the leaking water had come from. I ran the washer without the front cover (cold water) and it didn't leak. When I finally accidentally blocked the intake on the tub did it squirt out inside the washer. It turned out that it would only leak with both hot and cold water combined was the pressure big enough to leak. The place it leaked was about halfway between the intake valve and where it entered the tub in what looked like a small plastic housing with slots. The functionality of this thing is still in question. I call it the Kazoo because it makes noise so you can tell the water is going in. I can see that it also holds back pressure so the washer does not fill too fast if the incoming pressure is too high, but I have my doubts about this. It turns out the intake hose is interrupted with by a jet inside a 3 inch black rubber tube (valve) that extends into the second hose. The water pressure expands the rubber (valve)and makes noise. The way I see it old rubber had maybe shrunk and lost its ability to resist pressure so it overflowed because too much water was coming through. The new piece I ordered was 3/8 inch longer then the one that came out. Maybe a planned obsolence part. (My wife wanted to buy a new washer and dryer at the first sign of trouble.) Anyway the repair was pretty simple. No clamps needed the old one is easy to undo and you just replace the kazoo. By the way while I was waiting on the parts to get here I just throttled the water pressure on the wall so it wouldn't leak. On this maytag washer you take off the screws on the front towards the bottom to start. I did not notice them untill I had damn destroyed the lid. After you remove the front cover there are 2 screws in the top front corners to remove and the the top pops off. They repair is easy understanding it took some thinking. Good luck.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 1 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 1- 2 hours
Tools: Nutdriver, Pliers, Screw drivers, Socket set
Customer: Frank from Patterson, CA

Leaking at top of tub when filling with water

Did repair as instructed by video, I'm 74 years old if I can do it anybody can!

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 1 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 30 - 60 mins
Tools: Nutdriver, Screw drivers, Socket set
Customer: Bart from GROVELAND, MA

Water was leaking at the injector.

Used a Phillips head screwdriver to allow removal of the front panel. Used a socket set to allow tipping back of the top panel of the washer, to access the injector assembly. Used nut driver to loosen hose clamp. Replaced old injector nozzle and valve. Inserted plastic injector nozzle into rubber injector valve, ensuring that the nozzle was completely inserted into the valve. VERY IMPORTANT: Moistened the rim of the rubber injector valve, and gently inserted it into the hose, to ensure that the valve did not unroll from the nozzle during insertion into the hose. I found this caused a more serious leak on my first attempt at replacing the injector assembly. Inserted the hose and injector back into injector sleeve and retightened the hose clamp. Then repositioned the top panel, and replaced the front panel.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 1 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers, Socket set
Customer: James from BEECHER, IL

Leaking

Watched the video first that was offered. Stating what tools needed size of socket needed. Step by step and how to do the job. Which was very helpful.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 1 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Socket set
Customer: Carlos from Miami, FL

Water leaking during fill up rear left

PartsSelect had diagram of repair area (Maytag website did not because it is looking for a 6 digit model number). Ordered parts needed, only used valve and nozzle kept old sleeve too much hastle to replace, hardest part was to get to area because need to remove front panel then prop top.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 1 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 30 - 60 mins
Tools: Nutdriver, Screw drivers, Socket set
Customer: Stephen from Mercer, PA

Washer was leaking when filling

I removed the front of the washer and lifted the top. I could see the water was leaking from injector nozzle. I looked online at PartSelect.com, found my model and make. Looked up the defective parts and ordered them. They came in three days. I installed the parts in about 20 minutes and it worked fine.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 1 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 30 - 60 mins
Tools: Screw drivers, Socket set
Customer: Robert from Berkeley, CA

Leaking from injector

Unplugged the washer. Then I removed the two screws at the bottom of the front panel that hold the front panel on. Then I removed two screws that hold top down, under front corners. Lifted top holding lid so as not to flop backwards. Then loosened front hose clamp on injector body. Replaced valve and nozzle. Replaced hose clamp, top and front panel. Bam ---did not leak anymore.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

2 of 4 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Pliers, Screw drivers, Socket set
Customer: Kenneth from Franklin, MA

Water leaking when in use ,upper back left side

unplug machine ,shut off water supply,Removed 2 lower front panel screws ,raise panel upward "hinge type motion"and removed , Remove 2 self tapping screws from under front corners, removed liquid bleach tube from upper connector ,raise top toward back of machine , place prop "piece of wood" to hold top up,removed 1 screw attaching injector ,now replaced injector assy and install with new hoses and clamps. then assemble in reverse order

Help other customers find the most helpful instructions.

Were these instructions helpful?   

Model Cross Reference

This part works with the following models:

PartSelect Number: PS11738945
Manufacturer Part Number: WP216201
Brand Model Number Description
MaytagA104Washer - Top Loading
MaytagA105Washer - Top Loading
MaytagA106Washer - Top Loading
MaytagA106SWasher - Residential
MaytagA107Washer - Top Loading
MaytagA107SWasher - Residential
MaytagA108Washer - Top Loading
MaytagA108SWasher - Residential
MaytagA110Washer - Top Loading
MaytagA112Washer - Top Loading
MaytagA15CAWasher
MaytagA15CMWasher
MaytagA15CTWasher
MaytagA16CAWasher
MaytagA16CMWasher
MaytagA16CTWasher
MaytagA17CAWasher
MaytagA17CMWasher
MaytagA17CTWasher
MaytagA180Washer - Top Loading
MaytagA181Washer - Top Loading
MaytagA182Washer - Top Loading
MaytagA183Washer - Top Loading
MaytagA18CAWasher
MaytagA18CMWasher
MaytagA18CTWasher
MaytagA190Washer - Top Loading
MaytagA1910Washer - Top Loading
MaytagA206Washer - Top Loading
MaytagA206SWasher - Top Loading